Mada za sehemu hiiTesting electro-mechanical componentsMada 5
- Testing thermostat
- Testing relays and overload
- Testing capacitors
- Testing compressor
- Testing defrost timer
Testing Relays and Overloads
In refrigeration and air conditioning systems, relays and overloads are safety devices that protect the compressor motor from damage. Knowing how to test these components is an essential skill for any refrigeration technician. This note will guide you through the step-by-step process of testing relays and overloads using a digital multimeter.
A relay is an electrically operated switch that uses a small current to control a larger current. In refrigeration systems, the relay connects the start winding of the compressor motor to the power supply for a short time during startup.
Purpose of a relay:
- Provides the initial boost of current needed to start the compressor motor
- Disconnects automatically once the motor reaches normal speed
- Protects the motor from running on start windings too long
An overload (also called an overload protector) is a safety device that monitors the current flowing through the compressor motor. If the current becomes too high (indicating a problem), the overload trips and cuts off power to the motor.
Purpose of an overload:
- Protects the compressor motor from overheating
- Prevents damage caused by excessive current
- Automatically resets when the motor cools down
Before testing, gather these tools:
- Digital multimeter
- Screwdrivers
- Wire stripper
- Combination plier
- Wooden board (for mounting components during testing)
- Safety boots and overalls
Step-by-step Procedure
-
Disconnect power — Ensure the system is unplugged or the power supply is turned off before beginning any test.
-
Locate the relay — Find the relay connected to the compressor terminal housing. Note the terminals marked as:
- S (Start)
- R (Run)
- C (Common)
-
Remove the relay — Carefully pull the relay from its socket. Place it on the wooden board for testing.
-
Set the multimeter — Turn the dial to resistance (Ω) or continuity test mode.
-
Test the coil resistance — Place the multimeter probes on the two small terminals of the relay (the coil terminals). A healthy relay shows a resistance reading between 5Ω and 50Ω. If the reading shows infinite resistance (OL), the coil is broken and the relay is faulty.
-
Test the contacts — Place the probes on the common (C) and start (S) terminals. With the relay at rest, you should get a reading of infinite resistance (open circuit). Then, manually depress the relay contact arm and check for zero or very low resistance (closed circuit).
-
Interpret results:
- Coil resistance within range + contacts work properly = Relay is good
- Coil shows infinite resistance = Relay coil is faulty — replace
- Contacts do not close when pressed = Relay contacts are bad — replace
Step-by-step Procedure
-
Disconnect power — Always turn off power before testing.
-
Locate the overload — The overload is usually found on the side of the compressor terminal cover or near the relay.
-
Remove the overload — Carefully disconnect the overload from its connections. It may have two or three terminals.
-
Set the multimeter — Turn the dial to resistance (Ω) or continuity mode.
-
Test for continuity — Place one probe on each terminal of the overload. A good overload will show:
- Zero or very low resistance (continuity) when the overload is closed (not tripped)
- Infinite resistance (OL) when the overload has tripped due to excessive heat or current
-
Test the overload in the circuit — With power still off, test across the two line terminals where the overload is connected in the circuit. You should get a reading of zero or near zero if the overload is good and not open.
-
Interpret results:
- Shows continuity (low resistance) = Overload is good
- Shows infinite resistance (OL) = Overload is open/tripped and needs replacement
Scenario: You are testing a refrigeration system that won't start. The customer says the compressor runs for a few minutes then stops.
Testing process:
- You disconnect power and remove the relay from the compressor.
- Using the multimeter set to Ω, you test the relay coil between the two small terminals. The reading shows 12Ω — within the normal range of 5Ω to 50Ω.
- You manually actuate the relay contacts. They close properly with near-zero resistance.
- The relay is working correctly, so you test the overload.
- You set the multimeter to continuity and place probes on the overload terminals. The reading shows "OL" (infinite resistance), meaning the overload is open (tripped) and has failed.
- Conclusion: The overload protector is faulty and must be replaced to restore the system to working condition.
- Always disconnect power before testing any electrical component
- Wear safety boots and overalls while working
- Use insulated tools to prevent electric shock
- Never touch bare terminals while the system is powered
- Ensure the work area is dry before testing
Testing relays and overloads is a straightforward process using a digital multimeter. The relay is tested by checking coil resistance and contact operation. The overload is tested by checking for continuity across its terminals. A good relay shows coil resistance between 5Ω and 50Ω with working contacts. A good overload shows continuity (low resistance). Faulty components show infinite resistance (OL) and must be replaced.
In Tanzania, refrigeration technicians use these testing skills when repairing refrigerators in markets, restaurants, and fish-processing businesses along Lake Victoria. For example, a technician in Mwanza might test a restaurant's walk-in cooler that keeps shutting down. By using a multimeter to check the relay and overload, they can quickly identify whether a faulty overload (perhaps costing TZS 15,000–25,000 to replace) is causing the problem, saving the business from buying an expensive new compressor worth over TZS 500,000.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment and materials
- Test relay and overload
- Apply safety gears
- Clean workplace, tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Test electrical and mechanical faults as per conforms
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Use analog and digital Multimeter
- Identify different types of relays and overload
Principles: The student should explain the principle of operating characteristics of relay and overload
Theories: The student should explain:
- The types and identification of Relays and overload
Detailed knowledge about:
- Safe handling of measuring instruments
- Safe handling of tools, equipment
Swali
What is the normal resistance range for a healthy relay coil when tested with a digital multimeter?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado