Mada za sehemu hiiTesting electro-mechanical componentsMada 5
Testing a Compressor
A compressor is the heart of any refrigeration or air conditioning system. It pumps refrigerant through the system to create cooling. Testing a compressor means checking if the motor inside it is working properly before installing it in a refrigerator or air conditioner.
Before mounting a compressor into a refrigeration system, we must verify that:
- The motor windings are not damaged or burnt
- The compressor is not short-circuited or open-circuited
- The compressor is safe to handle and install
Testing saves time and money by identifying faulty compressors early.
- Wear safety boots and overalls before handling tools
- Ensure the work area is clean and dry
- Always disconnect power before testing
- Handle the compressor carefully to avoid damage
- Use insulated tools when working with electrical components
- Digital Multimeter
- Screwdrivers
- Combination pliers
- Wire stripper
- Wire cutter
- Wooden board (for mounting during testing)
Step 1: Visual Inspection
Examine the compressor housing for visible damage such as cracks, oil leaks, or rust. Check the terminal cover and ensure all three terminals are clean and undamaged.
Step 2: Identify the Terminals
A compressor typically has three terminals:
- S – Start winding
- R – Run winding
- C – Common terminal
These terminals are usually marked on the compressor body or can be identified using the multimeter.
Step 3: Test for Open Circuit
Set the multimeter to resistance (Ω) mode. Test the resistance between each pair of terminals:
- R to S
- R to C
- S to C
If the multimeter shows "1" or infinite resistance between any two terminals, the winding is open (broken) and the compressor is faulty.
Step 4: Test for Short Circuit
With the multimeter still in resistance mode, touch one probe to any terminal and the other probe to the compressor body (metal part).
- If the multimeter shows very low resistance (close to 0Ω), there is a short circuit
- A good compressor should show infinite resistance (no continuity) between terminals and the body
Step 5: Measure Winding Resistance
Record the resistance values between terminal pairs:
| Terminal Pair | Expected Reading |
|---|---|
| R to S | Highest value |
| R to C | Lowest value |
| S to C | Middle value |
The actual values depend on the compressor size, but the three readings should add up correctly. If any reading is zero or unusually low, the compressor is damaged.
Step 6: Record and Interpret Results
Compare your readings with standard values or with a known good compressor of the same model. Document all findings to determine if the compressor is serviceable or should be replaced.
A technician tests a domestic refrigerator compressor and obtains these readings:
- R to S: 15 Ω
- R to C: 8 Ω
- S to C: 7 Ω
Analysis: The readings follow the correct pattern (R-S is highest, R-C is lowest, S-C is middle). Adding R-C and S-C gives 8 + 7 = 15 Ω, which equals R-S. This indicates the windings are healthy and the compressor is good for installation.
If the technician had obtained 0 Ω between R and C, this would indicate a short circuit, meaning the compressor is faulty.
Testing a compressor involves:
- Visual inspection for physical damage
- Identifying the three terminals (S, R, C)
- Testing for open circuits (infinite resistance)
- Testing for short circuits (low resistance to body)
- Measuring winding resistances to verify healthy connections
Always use the digital multimeter correctly and follow safety procedures throughout the test.
In Tanzania, many households and small businesses rely on refrigerators and air conditioners, especially in hotels, restaurants, and clinics. A student who learns compressor testing can start a small repair business in their village or town, testing compressors before installing them and saving clients from buying faulty parts. For example, a technician in Dar es Salaam can charge about TZS 30,000 to 50,000 for testing and diagnosing a faulty refrigerator compressor, helping families avoid expensive replacements.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment and materials
- Make electric circuits diagram of test compressor
- Test compressor motor pump
- Apply safety gears
- Clean workplace, tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Test electrical and mechanical faults as per conforms
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Use analog and digital Multimeter
- Apply different types of test compressor
Principles: The student should explain the principle of operating characteristics of the compressor
Theories: The student should explain:
- Compressor types
Detailed knowledge about:
- Safe handling of measuring instruments
- Safe handling of tools, equipment
Swali
What are the three terminals of a compressor labelled as?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado