Mada za sehemu hiiConstructing plane and diagonal scalesMada 1
- Drawing plain and diagonal scales
A scale is a ratio that shows how the dimensions on a drawing compare to the actual dimensions of the object being represented. In Technical Drawing, we use scales to draw large objects on paper while keeping their proportions correct.
A scale is a ratio that compares the length on the drawing to the actual length of the object. It allows draftspeople to represent objects that are too large or too small to be drawn at their real size.
Representative Fraction (RF)
The Representative Fraction (RF) is the ratio of the drawing length to the actual length, expressed as a fraction with both numbers in the same unit.
RF=Actual lengthDrawing length
For example, if a scale is 1:100, this means 1 unit on the drawing equals 100 units in real life. The RF would be:
RF=1001
The two main types of scales you will construct are:
- Plain Scale – shows a limited number of primary divisions and sub-divisions in a straight line
- Diagonal Scale – allows reading smaller subdivisions using the principle of similar triangles
A plain scale represents whole units and their tenths (sub-divisions).
Steps to Construct a Plain Scale
- Determine the RF based on the size of the object and the paper available
- Draw a horizontal line and mark point A as zero
- Mark point B at a distance representing the "main" unit (for example, 1 m or 10 m)
- Divide AB into equal parts representing the primary divisions
- From point A, draw a short perpendicular line and mark sub-divisions at the top
- Complete the scale by drawing horizontal lines across the sub-divisions
- Number the divisions starting from zero at the left
Worked Example
Draw a plain scale of RF = 1/100 to represent metres, showing 10 m on the scale.
Solution:
- The RF = 1/100 means 1 cm on the drawing represents 100 cm (1 m) in reality
- To show 10 m, we need a scale length of 10 cm
- Draw a line 10 cm long and divide it into 10 equal parts (each part = 1 m)
- Each metre is further divided into 10 equal parts to read tenths (0.1 m)
The scale will allow you to read measurements like 3.5 m directly.
A diagonal scale provides greater accuracy by allowing you to read smaller divisions (usually hundredths) using diagonal lines.
Steps to Construct a Diagonal Scale
- Determine the RF and decide what unit the scale will represent
- Draw a horizontal line and mark the primary divisions (similar to a plain scale)
- At the left end, draw a short vertical line equal to one primary unit
- Divide the left-hand primary unit into 10 equal horizontal parts (for tenths)
- Divide the right-hand vertical side into 10 equal parts
- Draw diagonal lines connecting corresponding points: from the first horizontal division on the left to the second on the right, the second to the third, and so on
- Number the divisions on the left (tenths) and bottom (hundredths)
Worked Example
Draw a diagonal scale of RF = 1/100 to read up to 1 m and show hundredths of a metre (cm).
Solution:
- Draw a rectangle 1 cm wide (representing 1 m) and about 2 cm tall
- Divide the height into 10 equal parts (tenths of a metre = 10 cm)
- Divide the right vertical side into 10 equal parts
- Draw diagonals from each division point on the left to the next higher division on the right
- Read measurements: the horizontal line from any diagonal point gives the hundredths
The diagonal scale allows you to read measurements like 0.73 m (73 cm) directly.
In Tanzania, construction workers and architects use plain and diagonal scales when reading building plans. For example, when a mason in Dar es Salaam receives a floor plan drawn at a scale of 1:100, they can use a scale ruler to measure that a wall should be 5 metres long on the actual building, even though the drawing shows only 5 centimetres. This ensures doors, windows, and walls are built with the correct sizes, preventing expensive mistakes during construction.
Jinsi utakavyotathminiwaTathmini ya mchakato
Tathmini ya mchakato
Plain and diagonal scales are constructed as per specifications.
Swali
What does a Representative Fraction (RF) represent in technical drawing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado