Mada za sehemu hiiSectioning of engineering componentsMada 2
- Drawing sections
- Drawing standard symbols
Drawing Standard Symbols
Standard symbols are simplified graphical representations used in technical drawing to convey specific information quickly and clearly. When drawing sectional views, several standard symbols and conventions must be used to ensure the drawing is understood by anyone who reads it. This lesson covers the key symbols used when representing sections in engineering and building drawings.
A cutting plane line indicates where an imaginary cut is made through an object to reveal its interior. This is the foundation of section drawing.
Key features:
- Drawn as a thick line with alternating long and short dashes
- The long dashes are approximately 20-30 mm long
- The short dashes are approximately 5-10 mm long
- The line width should be about 0.5-0.7 mm
Drawing the cutting plane line:
- Draw a continuous thick line along the path of the cut
- At each change of direction (bends), make the line thicker or add an arrow
- Place arrows at one or both ends showing the viewing direction
- Add letters (such as A-A, B-B) at each end to name the section
The arrows point in the direction you are looking at the section. For example, if the cutting plane line is labelled "A-A" with an arrow pointing right, the section view should be drawn as if you are looking toward the right.
Section lines (also called hatching) are thin lines drawn inside the area that has been cut to indicate the material being shown.
General rules for section lining:
- Lines are thin (approximately 0.3 mm line width)
- Lines are drawn at 45° to the horizontal, unless otherwise specified
- Lines are evenly spaced (typically 2-4 mm apart)
- Lines should be consistent in angle and spacing throughout one drawing
- Hatching stops at the boundary of the cut surface
Drawing section lines:
- Identify the boundaries of the cut surface
- Draw a series of parallel 45° lines within those boundaries
- Ensure even spacing between all lines
- Make sure lines meet the edges cleanly without extending beyond
Different materials are represented by different hatching patterns. The table below shows common material symbols:
| Material | Symbol Description |
|---|---|
| Concrete | Dots and diagonal lines combined |
| Brick | Diagonal lines with occasional offset |
| Wood (end grain) | Annual rings (circles) |
| Wood (cross grain) | Parallel wavy lines |
| Steel | Diagonal lines with additional cross-hatching |
| Glass | Empty or solid fill |
| Earth/soil | Irregular dotted pattern |
Note: In building drawings, concrete is often shown with small dots between diagonal lines. Brick walls may be shown with diagonal lines, sometimes with a gap to represent mortar joints.
Technical drawings use standard abbreviations to save space. Common abbreviations include:
- TH. or th. — Thickness
- W. or w. — Width
- D. or d. — Depth or Diameter
- L. or l. — Length
- C/C — Centre to centre
- O.D. — Outside diameter
- I.D. — Inside diameter
- Min. — Minimum
- Max. — Maximum
- C.L. — Centre line
- FFL — Finished Floor Level
- FFL — Finished Floor Level
- GL — Ground Level
- PL — Plinth Level
When dimensioning sectional drawings, standard symbols are used:
- Ø — Diameter (for circular sections)
- R — Radius (for rounded edges in section)
- □ — Square (for square sections)
- ⧄ — Square (alternative)
Drawing a simple section of a concrete column:
Given: A rectangular column 300 mm × 300 mm cut by a vertical section.
Steps to draw:
-
Draw the cutting plane line — Draw a thick line with long and short dashes along the centre of the column. Label it "A-A" with arrows.
-
Draw the section outline — Draw the rectangular outline of the column (300 mm × 300 mm) where it is cut.
-
Apply section lines — Within the cut rectangle, draw diagonal 45° lines at even spacing (approximately 3 mm apart). This represents concrete.
-
Add dimensions — Write "300" on both sides of the section to show the column dimensions.
-
Add material note — Label the section as "CONCRETE" or add a note in the title block.
- Always use the correct line thickness: thick lines (0.5-0.7 mm) for cutting plane lines, thin lines (0.3 mm) for hatching
- Maintain consistent spacing between hatching lines
- Use a 45° set square or protractor to ensure accurate angles
- When different materials meet in a section, leave a small gap between different hatching patterns
- Include a legend or key if using non-standard symbols
- Ensure all symbols align with the TIE textbook conventions
In Tanzania, when a technician or artisan reads building plans from an architect, they rely on standard symbols to understand what materials to use and how structural elements are constructed. For example, a m mason at a construction site in Mwanza or Arusha will read section drawings showing concrete foundations with hatching patterns and understand that the foundation is made of concrete, while walls shown with brick symbols indicate where brickwork is required. This ensures buildings are constructed correctly according to the design, preventing costly mistakes and structural problems.
Jinsi utakavyotathminiwaTathmini ya mchakato
Tathmini ya mchakato
Standard symbols and conventions of engineering components are drawn as per ISO.
Swali
What is the typical line width for a cutting plane line in technical drawing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado