Mada za sehemu hiiDrawing conic sectionMada 1
- Constructing conic sections
Constructing Conic Sections
Conic sections are the curves obtained when a plane cuts through a cone at different angles. In technical drawing, the most commonly used conic section is the ellipse — a oval-shaped curve used to represent circular objects when viewed at an angle, such as pipes, holes, and cylindrical shapes in plan or isometric views. This note explains how to construct an ellipse accurately using two standard methods.
When a cone is cut by a plane at different angles, four different curves are produced:
- Circle — when the cutting plane is parallel to the base of the cone
- Ellipse — when the cutting plane cuts through the cone at an angle, but not parallel to the base or side
- Parabola — when the cutting plane is parallel to the side of the cone
- Hyperbola — when the cutting plane cuts through the cone vertically
At Form 2 level, you are expected to construct an ellipse using geometric methods.
This method draws an ellipse inside a rectangle by plotting points and connecting them with a smooth curve.
Steps
-
Draw the rectangle to the required dimensions (length = major axis, width = minor axis). For example, to draw an ellipse with major axis AB=100 mm and minor axis CD=60 mm:
- Draw horizontal line AB=100 mm
- Draw vertical line CD=60 mm, with C and D as the midpoints of AB
-
Divide the rectangle:
- Divide the top half of the rectangle into any number of equal parts (usually 4 or 6)
- Divide the bottom half the same way
- Mark these division points on the top and bottom edges
-
Plot points:
- From each division point on the top edge, draw a line to corner D (bottom-left corner)
- From the corresponding division point on the bottom edge, draw a line to corner C (top-left corner)
- Where each pair of lines crosses is a point on the ellipse
-
Draw the curve:
- Join all the plotted points with a smooth, continuous freehand curve or using a French curve
- The resulting shape is an ellipse
This method uses two circles with diameters equal to the major and minor axes of the ellipse.
Steps
-
Draw the axes:
- Draw the major axis AB (longer diameter) and minor axis CD (shorter diameter) perpendicular to each other at their midpoints
-
Draw the circles:
- Using O (the intersection of the axes) as centre, draw a circle with diameter equal to the major axis AB
- Using the same centre O, draw a second circle with diameter equal to the minor axis CD
-
Mark radial lines:
- From centre O, draw a series of radial lines (at equal angles, e.g., every 15°) extending from the centre to the outer circle
- Number these lines 1, 2, 3, 4, and so on
-
Locate points on the ellipse:
- From each point where a radial line meets the outer circle, draw a horizontal line inward
- From the corresponding point where the same radial line meets the inner circle, draw a vertical line inward
- The intersection of each horizontal and vertical line is a point on the ellipse
-
Complete the ellipse:
- Join all intersection points with a smooth curve using a French curve or by hand
Problem: Construct an ellipse with major axis 80 mm and minor axis 50 mm using the rectangle method.
Solution:
- Draw rectangle ABCD with width 80 mm and height 50 mm.
- Mark the midpoint of each side. The long edges are divided into 4 equal parts (20 mm each).
- From each division point on the top edge, draw lines to bottom-left corner.
- From each division point on the bottom edge, draw lines to top-left corner.
- Mark where each pair of lines crosses — these are points on the ellipse.
- Connect all points with a smooth curve to complete the ellipse.
- The major axis is the longest diameter of the ellipse; the minor axis is the shortest diameter
- Both axes bisect each other at right angles at the centre of the ellipse
- Use a French curve (set square with curved edges) to draw smooth, professional-looking ellipses
- Always construct light construction lines first, then darken the final curve
- The ellipse represents a circle seen at an angle — this is why circular holes appear as ellipses in isometric and plan views
In Tanzania, construction workers and architects use ellipse construction when reading and creating technical drawings for buildings. For example, when drawing a cylindrical water tank or a round manhole cover in a floor plan (which is viewed from above at an angle), the circular shape appears as an ellipse. A technician reading a building plan must correctly interpret these ellipses to understand the actual sizes and positions of cylindrical elements on the construction site.
Jinsi utakavyotathminiwaTathmini ya mchakato
Tathmini ya mchakato
Various types of conic sections are described, and constructed.
Swali
What is the most commonly used conic section in technical drawing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado