Mada za sehemu hiiConstructing basic curvesMada 2
- Constructing cycloids, epi-cycloid and hypo-cycloids
- Constructing trochoids
A trochoid is a curve generated by a point fixed to a circle when the circle rolls without slipping along a straight line. Unlike a cycloid, where the generating point lies on the circumference of the rolling circle, a trochoid has its generating point either inside or outside the circumference of the rolling circle.
There are two types of trochoids:
Inferior Trochoid (Prolate Cycloid)
This is generated when the point is fixed inside the circumference of the rolling circle. Since the point is closer to the centre than the circumference, it produces a curve with loops that extend below the baseline.
Superior Trochoid (Curtate Cycloid)
This is generated when the point is fixed outside the circumference of the rolling circle. Since the point is farther from the centre than the circumference, it produces a wavy curve without loops.
A superior trochoid is drawn when the generating point lies outside the circumference of the rolling circle.
Procedure:
-
Draw the rolling circle of given diameter. From its centre C, draw a horizontal baseline equal to the circumference (πD).
-
Divide the baseline into eight equal parts. Label the division points as C₁, C₂, C₃, ... up to C₈, where C₀ is at the starting position.
-
Locate point P outside the circumference of the rolling circle. Measure the distance CP.
-
Draw the radius circle: Using radius CP (which is larger than the rolling circle's radius), draw a new circle centred at C₀.
-
Divide this new circle into eight equal parts and label the points as 1, 2, 3, ... 8 on the circumference.
-
Find successive positions: With centre C₁ and radius CP, draw an arc to intersect the horizontal line drawn from point 1. This gives point P₁. Repeat for centres C₂, C₃, ... C₈ to find points P₂, P₃, ... P₈.
-
Join the points: Connect P₀, P₁, P₂, ... P₈ with a smooth curve using a French curve. This curve is the superior trochoid.
An inferior trochoid is drawn when the generating point lies inside the circumference of the rolling circle.
Procedure:
-
Draw the rolling circle of given diameter. From its centre C, draw a horizontal baseline equal to the circumference (πD).
-
Divide the baseline into eight equal parts and label them C₁, C₂, C₃, ... up to C₈.
-
Locate point P inside the circumference of the rolling circle. Measure the distance CP.
-
Draw the radius circle: Using radius CP (which is smaller than the rolling circle's radius), draw a new circle centred at C₀.
-
Divide this new circle into eight equal parts and label points 1, 2, 3, ... 8.
-
Find successive positions: With centre C₁ and radius CP, draw an arc to intersect the horizontal line from point 1. This gives point P₁. Repeat for all centres.
-
Join the points: Connect P₀ through P₈ with a smooth curve to obtain the inferior trochoid.
Question: A circle with radius 30 mm rolls along a straight line for one complete revolution. Point P₁ is fixed 15 mm from the centre (inside the circle), and point P₂ is fixed 5 mm outside the circumference. Construct both trochoids.
Solution:
For the rolling circle:
- Radius = 30 mm
- Circumference = πD = π × 60 = 188.5 mm
For inferior trochoid (point P₁ inside):
- Distance CP₁ = 15 mm (less than radius)
- Follow the inferior trochoid procedure using radius 15 mm
For superior trochoid (point P₂ outside):
- Distance CP₂ = 30 + 5 = 35 mm (greater than radius)
- Follow the superior trochoid procedure using radius 35 mm
The inferior trochoid will show loops at the baseline, while the superior trochoid will appear as a smooth wavy curve above the baseline.
| Type of Trochoid | Position of Point | Alternative Name |
|---|---|---|
| Inferior Trochoid | Inside the circle | Prolate Cycloid |
| Superior Trochoid | Outside the circle | Curtate Cycloid |
The key difference is that when the point is inside the circle, the curve dips below the generating line (loops); when outside, the curve stays above the line (no loops).
In Tanzania, trochoids are used in designing gear teeth profiles for machines like maize mills and water pumps found in many trading centres. When a gear rolls along a rack, the teeth contact points follow trochoidal curves, ensuring smooth transmission of power and reducing wear on mechanical parts used in small-scale industries.
Jinsi utakavyotathminiwaTathmini ya mchakato
Tathmini ya mchakato
Trochoids are constructed as per given instructions.
Swali
What is another name for an inferior trochoid?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado