Mada za sehemu hiiConstructing basic curvesMada 2
- Constructing cycloids, epi-cycloid and hypo-cycloids
- Constructing trochoids
Constructing Cycloids, Epicycloids and Hypocycloids
When a circle rolls along a surface without slipping, a point fixed on its circumference traces a special curve called a cycloidal curve. These curves are important in engineering because they describe the actual path followed by points on rolling parts of machines. In this topic, you will learn how to construct three types of cycloidal curves: the cycloid, epicycloid, and hypocycloid.
Definition
A cycloid is the locus of a point on the circumference of a circle which rolls without slipping along a flat surface (straight line). The circle which rolls is called the generating circle, and the straight line along which it rolls is called the baseline.
The condition of "rolling without slipping" is important because it ensures that the point on the circle continues moving and its path can be traced accurately.
Construction Procedure
To construct a cycloid, follow these steps:
-
Draw the generating circle of a given diameter. From point P (the tracing point), draw a baseline (horizontal line) whose length equals the circumference of the generating circle.
-
Divide the circle and baseline into the same number of equal parts (usually 8 or 12 parts). Erect perpendicular lines from each division point on the baseline to intersect with the horizontal line through the centre of the circle.
-
Locate the new centres — from each division point on the baseline, draw vertical lines upward. These represent the positions of the centre of the rolling circle at each step.
-
Draw arcs — with the radius of the generating circle and using each new centre (C₁, C₂, C₃...Cₙ), draw arcs that intersect with horizontal lines projected from the corresponding points on the circle.
-
Mark intersection points — the points where these arcs intersect are the positions of the tracing point P at each stage.
-
Join the points — connect all the intersection points with a smooth curve (using a French curve or freehand). This curve is the required cycloid.
Worked Example
Problem: A circle with centre O and radius OA = 25 mm is fixed at point A touching a horizontal plane. The point A is rolled along a straight line AA' with length equal to the circumference of the circle. Construct the cycloid generated by the circle.
Solution:
-
Draw a circle with radius 25 mm and divide it into 8 equal parts. Label the points as A, B, C, D, E (for the half circle).
-
Calculate the circumference: C=2×π×25 = 157 mm. Draw line AA' = 157 mm and divide it into 8 equal parts (each part = 19.6 mm).
-
From points 2 to 8 on the baseline, draw vertical lines to intersect with horizontal lines drawn through the centre O. These give the new centres O₂, O₃, O₄...O₈.
-
With radius OA = 25 mm and centre O₂, draw an arc to intersect with the horizontal line projected from point B on the original circle. Repeat this for centres O₃, O₄...O₈, intersecting with horizontal lines from points C, D, E and so on.
-
Starting from point A, join all intersection points with a smooth curve. This is the cycloid.
Application of Cycloids
Cycloid curves are used in:
- Designing gear tooth profiles
- Designing mould boxes in foundry shops
- Kinematics (motion studies) and mechanisms that work with rolling contacts
Definition
An epicycloid is the locus of a point on the circumference of a circle which rolls without slipping around the outside of another circle. The circle that rolls is called the generating circle, and the larger stationary circle is called the directing circle.
Construction Procedure
-
Draw and divide the rolling circle into 8 or 12 equal divisions. Mark the points on the circumference.
-
Transfer the divisions onto the baseline (the circumference of the directing circle).
-
Mark the positions of the centre of the rolling circle as it rolls around the directing circle. These centres (C₁, C₂...C₁₂) lie on an arc that follows the path of the rolling circle's centre.
-
Project the positions of the points from the circle onto the new positions.
-
Draw arcs — using the radius of the rolling circle and from each marked centre (C₁, C₂, C₃...), cut off arcs through points 1, 2, 3...12 on the circumference.
-
Connect the points where these arcs intersect to form a smooth curve.
-
Thicken the curve to make it more visible. This is the epicycloid.
Worked Example
Problem: A point fixed on a small circle with radius 3 mm is rolling without slipping along a large circumference which has a radius of 12 mm. Draw the epicycloid of the small circle.
Solution:
-
Draw a large circle (directing circle) with radius 12 mm and a small rolling circle with radius 3 mm. Divide the rolling circle into 6 equal parts.
-
Calculate the circumference of the smaller circle: C=2×π×3 = 18.85 mm Calculate the circumference of the larger circle: C=2×π×12 = 75.40 mm
Find the angle θ: since the rolling circle makes one complete revolution around the larger circle, θ = 360° × (radius of larger circle ÷ radius of smaller circle) = 360° × (12 ÷ 3) = 1440° (or 4 complete revolutions)
-
Divide the angle θ into 6 equal parts (since we divided the rolling circle into 6 parts).
-
Draw the arc which is the locus of the centre of the rolling circle (this arc has radius equal to the sum of the two radii: 12 + 3 = 15 mm).
-
The lines forming the angles in step 3 will intersect with the arc in step 4 to give the six positions of the centres of the rolling circle.
-
From each division point on the rolling circle, draw radii to intersect with the corresponding arc from point 2, 3, 4, 5 and 6.
-
Draw a smooth curve through these intersection points. This is the required epicycloid.
Application of Epicycloids
Epicycloid curves are used in:
- Designing planetary gears
- Automatic transmissions
- Epicyclic gear trains
- Mechanical watches
Definition
A hypocycloid is the locus of a point on the circumference of a circle which rolls without slipping around the inside of another circle. The construction is very similar to the epicycloid, but the rolling circle rotates on the underside (inside) of the base surface.
Construction Procedure
-
Divide the rolling circle into 12 equal parts and label the points on its circumference.
-
Transfer the 12 divisions onto the circumference of the base (directing) circle.
-
Mark the 12 positions of the circle's centre (C₁, C₂, C₃...C₁₂) as the circle rolls inside the base circle.
-
Project the positions of the points from the rolling circle.
-
Draw arcs — using the radius of the rolling circle and from the marked centres, cut off arc points.
-
Connect the arc points with a smooth curve and thicken it. This is the hypocycloid generated by the rolling circle.
Key Difference
Remember:
- Epicycloid: rolling circle moves on the outside of the directing circle
- Hypocycloid: rolling circle moves on the inside of the directing circle
Application of Hypocycloids
Hypocycloid curves are used in:
- Manufacturing hypocycloidal gears
- Designing robotic arm movements
- Slider-crank linkage mechanisms
| Type of Curve | Path Traced By |
|---|---|
| Cycloid | Point on circumference of circle rolling on a straight line |
| Epicycloid | Point on circumference of circle rolling outside another circle |
| Hypocycloid | Point on circumference of circle rolling inside another circle |
In Tanzania, the knowledge of constructing cycloids is applied when designing gear systems for small-scale maize mills and water pumps used in farming communities. For example, when a technician repairs a posho mill (kibaba chaini) in a village like Mkamba in Morogoro Region, understanding how gear teeth profiles follow cycloidal curves helps ensure the machine operates smoothly without jamming, which directly affects the cost of grinding maize and the livelihood of local farmers.
Jinsi utakavyotathminiwaTathmini ya mchakato
Tathmini ya mchakato
Basic curves are identified, distinguished and correctly constructed.
Swali
What is a cycloid in technical drawing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado