Mada za sehemu hiiPerforming shedding motionMada 3
- Reading a drafting and lifting plan
- Opening shed according to lifting plan
- Using a shed stick on a frame loom
Opening Shed According to Lifting Plan
When weaving on a handloom, the shed is the temporary V-shaped opening between warp yarns that allows the weft (horizontal yarn) to pass through. Opening the shed correctly according to the lifting plan is essential for creating accurate weave patterns and producing quality fabric.
What is a Shed?
A shed is the V-shaped temporary separation between upper and lower warp yarns to facilitate weft insertion. It is formed by raising or lowering the warp yarns through which the shuttle carrying the weft yarn passes.
What is Shedding?
Shedding is the process of raising and lowering warp yarns by harnesses (heald frames) to make an opening for the weft yarn to pass through. Shedding is one of the three primary motions needed to weave a fabric, along with picking and beating up.
There are two main types of sheds: open shed and closed shed. These are further divided into four sub-types:
- Open shed
- Semi-open shed
- Centre-closed shed
- Bottom-closed shed
Bottom-Closed Shed
Most handlooms prefer using the bottom-closed shed because:
- It is produced by moving only the yarns that form the upper line
- The warp stays level on the bottom line
- It is best suited for handloom weaving
Advantages of bottom-closed shed:
- Alternate tightening and slackening of warp yarns produces covered cloth
- Suitable for producing fine fabrics like silk
Disadvantages:
- More stress on the top warp line
- Higher chance of breakage on top warp line
- Lower loom speed
- More time required
The key to creating a good parallel shed lies in connecting all components of the shedding system. The system consists of five parts:
- Levers (A) – transmit movement
- V-shaped rope (B) – acts as intermediate lever between treadles and heald shafts
- Heald shaft / Heddles (C) – frames that hold and control warp yarns
- Lam rods (D) – link treadles to heald shafts
- Treadles (E) – foot pedals that control the movement of heddles
The shedding mechanism creates the opening for weft insertion through the following process:
- Shafts are suspended above the warp yarns
- When one shaft is pulled down by the treadle, the opposite shaft is simultaneously lifted
- This creates a vertical space (the shed) between lifted and non-lifted warp yarns
- The tie-up between shafts and treadles can be adjusted according to the number of shafts used
Opening a Shed According to Lifting Plan
The lifting plan indicates the order in which heald shafts should be lifted for each weft insertion to produce a particular weave pattern. To open a shed according to the lifting plan:
- Refer to the lifting plan – each row corresponds to one weft pick, columns correspond to shafts
- Tie up the treadles using cords according to the lifting plan to allow effective shed formation
- Press down the treadle to raise the selected warp yarns and create the shed
- Alternate working with your feet on the treadles, shifting between left and right foot in a consistent pattern
Materials needed:
- Handloom
- Cords
- Lifting plan
Steps to open a shed:
- Tie up the treadles using cords in a manner that allows effective shed formation according to the lifting plan
- Press down the treadle to raise the warp yarns and create a vertical space between raised and unraised yarns
- This action lifts certain warp yarns, forming the shed
- Alternate working with your feet on the treadles, shifting between left and right foot consistently (left, right, left, right...) to control shed formation for successive weft insertions
- The lifting plan shows which heald shafts should be raised or lowered for each pick
- Proper shed formation ensures even interlacing of warp and weft yarns
- The bottom-closed shed is preferred in handloom weaving because it is best suited for this type of loom
- The shedding mechanism uses treadles connected through lam rods to heald shafts (heddles)
In Tanzania, weavers in communities like Tanga, Arusha, and Bagamoyo use handloom weaving to produce local textiles such as kangas, kitenge, and weaving baskets. Understanding how to open the shed according to the lifting plan enables local weavers to create intricate patterns for sale in markets, supporting small-scale textile businesses and preserving traditional craftsmanship.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment A Process
- Observe safety precautions
- Open shed as per lifting plan
- Clean tools and work place
- Store tools and equipment
Tathmini ya matokeo
The shed is properly opened as per lifting plan
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: Open a shed according to lifting plan Principle: The student should explain the principles of: Penning shed according to lifting plan
Theories: The student should explain:
- Types of sheds,
- Describe shedding systems and the mechanism to open a shed according to the lifting plan
- Shedding is affected on loom frame
- How the shedding process is affected
- Bolton-closed and centreclosed shedding Loom shedding
Circumstantial knowledge: Detailed knowledge of:
- Workshop safety rules
- Safe handling of working tools
Swali
What is a shed in handloom weaving?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado