Mada za sehemu hiiPerforming plasteringMada 4
- Performing internal plaster
- Performing external plaster
- Performing tyrolean
- Performing final finish to the plaster (skimming)
Internal plastering is the process of applying a thin coat of mortar to cover rough or uneven surfaces of internal walls, columns, and ceilings. This technique provides a smooth and aesthetically pleasing finish while protecting the underlying structure from moisture and enhancing durability. Plastering also conceals imperfections or flaws in workmanship, creating a uniform and professional appearance throughout the building.
Different types of plaster are used depending on the wall surface and requirements:
- Cement plaster – Durable mixture of cement, sand, and water; used for interior and exterior surfaces
- Gypsum plaster – Sets quickly and provides a smooth finish; commonly used for interior walls and ceilings
- Lime plaster – Flexible and breathable; suitable for historic buildings and humid environments
- Mud plaster – Used in traditional and sustainable building practices
- Stucco plaster – Durable multipurpose finish for exterior and interior walls
A good plaster should meet the following criteria:
- Adhere properly to the background surface
- Be hard and durable to resist weathering conditions
- Possess good workability for easy application
- Offer good insulation against sound
- Be economical and cost-effective
- Be possible to apply in various weather conditions
- Provide good fire resistance
- Create a smooth, non-absorbent, and washable surface
Proper surface preparation ensures good plaster adhesion and a smooth finish:
- Clean the surface – Remove dust, oil, grease, and other contaminants using a wire brush
- Roughen mortar joints – Keep wall joints rough to create a strong bond for the plaster
- Rake out joints – For smooth or old walls, rake mortar joints to a depth of at least 12mm
- Fill cavities – Repair any cracks, holes, or cavities with appropriate materials
- Remove projections – Knock off any projections greater than 10mm for a uniform surface
- Moisten the wall – Wash and moisten the wall surface for at least 6 hours before plastering to prevent rapid water absorption
To achieve consistent plaster thickness across the wall:
- Fix dots – Attach small plaster patches (15mm × 15mm, 10mm thick) as reference points
- Space dots – Position dots approximately 2 metres apart, both horizontally and vertically
- Check alignment – Use a plumb-bob to ensure dots are vertically aligned
- Form screeds – Create vertical strips of plaster between the dots to serve as guides for maintaining consistent thickness
The base coat provides the main thickness of the plaster:
- Thickness – Approximately 12mm for brick masonry
- Mix ratio – Cement to sand ratio of 1:3 to 1:6
- Application – Apply plaster between the screeds using a trowel
- Levelling – Level the surface using flat wooden floats and straight edges
- Keying – While the coat is still semi-set, roughen the surface with a scratching tool to create a bond for the finishing coat
The finishing coat creates the final smooth surface:
- Thickness – 2mm to 3mm (or 4mm as per some specifications)
- Mix ratio – Cement to sand ratio of 1:4 to 1:6
- Preparation – Dampen the base coat evenly before application
- Application – Apply with a wooden float for an even surface, then use a steel trowel for a polished finish
- Continuity – Apply continuously from top to bottom in one session to avoid visible joining marks
Proper curing ensures strength and durability:
- Duration – Keep plaster wet for at least 7 days (up to 28 days for maximum strength)
- Method – Sprinkle water over the surface regularly
- External surfaces – Use gunny bags to retain moisture during curing
- Importance – Prevents cracks and efflorescence (white powdery residue)
After completing plaster work:
- Clean doors, door frames, and floor surfaces to remove plaster splashes
- Begin curing within 24 hours after application when the plaster has hardened sufficiently
- Continue curing for at least 7 days to allow the plaster to reach desired strength
| Category | Items |
|---|---|
| Application tools | Trowel, hawk, wooden float, steel float, straight edge |
| Mixing tools | Mortar pan, spade, mixing container |
| Measuring tools | Tape measure, spirit level, mason's square |
| Surface preparation | Wire brush, bucket, sponge |
| Safety gear | Safety boots, overalls, helmets, gloves |
For internal walls, the cement mortar ratio is typically 1:5 to 1:6 (one part cement to five or six parts sand). The first coat is applied at 12mm thickness, and the finishing coat at 2-4mm thickness.
In Tanzania, internal plastering skills are essential for local builders and handymen who renovate houses in communities like Mwanza or Arusha. For example, a Form 2 graduate working as an apprentice with a local mason can apply internal plaster to create smooth walls in a client's new house, using locally available cement and sand, and charge approximately TZS 50,000-80,000 per square metre for the plastering work—providing both income and valuable construction skills for future building projects.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Prepare the wall surface by cleaning and wetting it
- Mix plaster materials (cement, sand, and water) to achieve the correct consistency
- Apply the first coat of plaster evenly across the wall surface
- Level and smooth the plaster using trowels and straight edges
- Apply the finishing coat for a smooth, uniform surface
- Inspect the wall for consistency, finish quality, and adherence to specifications
Tathmini ya matokeo
Internal plastering is carried out according to specification and standards to provide a smooth and durable finish on interior walls
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain procedures for internal plastering, including surface preparation, material mixing, and application techniques
Principles: The student should explain the principles involved in performing internal plaster
Theories: The student should explain-
- Surface preparation
- Application of dots
- Floating surface
Swali
What is the primary purpose of internal plastering in building construction?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado