Mada za sehemu hiiPerforming plasteringMada 4
- Performing internal plaster
- Performing external plaster
- Performing tyrolean
- Performing final finish to the plaster (skimming)
Performing External Plaster
External plastering, also called rendering, is the process of applying a protective and decorative coat to the outer walls of a building. It shields the walls from weather elements like rain and wind, improves durability, and enhances the overall appearance of the structure.
External plastering serves three main purposes:
- Protection – It guards the walls against rain, wind, sun, and other weather conditions that can damage the building structure.
- Durability – A well-applied external plaster extends the life of the wall by preventing water penetration and reducing wear.
- Appearance – It provides a smooth, even, and attractive finish to the exterior of the building.
Unlike interior walls, which are usually built to perfect plumb and line, exterior walls may have imperfect brickwork. External plastering covers these imperfections and creates a uniform surface.
The primary materials needed are:
- Cement – Provides binding strength and durability
- Sand – Acts as the aggregate; should be clean and free from impurities
- Water – Used to form the mortar mix; should be clean and suitable for mixing
The cement-to-sand ratio depends on the layer being applied:
- First layer (base coat): 1:3 ratio (1 part cement to 3 parts sand), thickness approximately 16mm
- Second layer (finish coat): 1:4 to 1:6 ratio, thickness 2mm to 3mm
The ratio 1:3 provides stronger adhesion and resistance to weather, making it suitable for the base coat on external surfaces.
Before starting, gather these tools:
- Trowel and plastering hawk
- Mortar pan for mixing
- Mason's square and spirit level
- Straight edge for leveling
- Floats (wooden and steel)
- Brush for cleaning
- Bucket and sponge
- Tape measure
- String for marking
Always wear the following protective equipment:
- Safety boots
- Overalls
- Helmet
- Gloves
Step 1: Surface Preparation
Clean the wall surface and joints thoroughly using a brush. Remove all dust, loose mortar, and debris.
Step 2: Rake the Joints
Use a rake or suitable tool to remove loose or protruding mortar from the joints. Fill any holes or cavities with fresh mortar to create an even surface.
Step 3: Set Out Screed Dots
Set plaster screed dots at intervals of 2 to 3 meters apart across the wall surface. Use a spirit level and plumb-bob to ensure the dots are perfectly vertical and level. These dots act as guides for maintaining consistent plaster thickness.
Step 4: Mix the Plaster
Combine cement, sand, and water in the required ratio (1:3 for the first layer). Mix thoroughly until you achieve a uniform, workable consistency. The mortar should be wet enough to spread easily but not too runny.
Step 5: Wet the Wall Surface
Water the entire wall surface evenly before applying plaster. This prevents the wall from absorbing water from the plaster too quickly, which can cause cracking and poor adhesion. Ensure the wall is moist but not dripping wet.
Step 6: Apply the Base Coat (Undercoat)
Using a trowel, apply the first layer of plaster (approximately 16mm thick) between the screed guides. Level the surface with a straight edge and wooden float. Work from top to bottom, covering one section at a time.
Step 7: Apply the Finishing Coat
After the base coat has set but not fully dried, apply the finishing coat (2mm to 3mm thick). Use a steel trowel to achieve a smooth, even surface. Apply continuously to avoid visible joining marks.
Step 8: Curing
Allow the plastered surface to dry for about 24 hours. Then begin curing by sprinkling water over the surface. Continue curing for at least 7 days to ensure the plaster gains full strength and durability.
A student needs to plaster an external wall that is 3 meters high and 5 meters wide.
Step 1: Calculate the wall area
Area=Height×Width=3m×5m=15m2
Step 2: Determine plaster volume for the base coat
With a 16mm (0.016m) thickness for the first layer:
Volume=Area×Thickness=15m2×0.016m=0.24m3
Step 3: Calculate cement and sand for 1:3 ratio
Total parts = 1 + 3 = 4 parts
- Cement volume = 0.24÷4=0.06m3
- Sand volume = 0.24×43=0.18m3
Assuming 1 bag of cement = 0.035m³ (approximately 50kg), the student would need about 2 bags of cement and 0.18m³ of sand for the base coat.
| Problem | Cause | Solution |
|---|---|---|
| Cracking | Wall too dry or plaster dries too fast | Wet the wall properly and cure regularly |
| Poor adhesion | Dirty or smooth surface | Clean surface thoroughly and rake joints |
| Uneven thickness | Incorrect screed spacing | Set screed dots at proper intervals (2-3m) |
| Visible lines | Applying finish in sections | Apply finishing coat continuously from top to bottom |
In Tanzania, a mason working on a residential building in Dar es Salaam would use external plastering skills to protect houses from the rainy season. For example, a small contractor plastering a 3-bedroom house exterior might charge around TZS 500,000 to TZS 800,000 for the plastering work, depending on the wall area and finish quality. Properly applied external plaster prevents water damage during the March-May rains, saving homeowners expensive repairs on wall cracks and dampness.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Clean and prepare the wall surface by removing dirt and loose particles
- Mix plaster materials (cement, sand, and water) to the required consistency
- Apply the first coat of plaster to the external surface evenly
- Level the plaster using straight edges and trowels
- Apply the finishing coat to ensure weather resistance and smoothness
- Inspect the surface for cracks, unevenness, and adherence to specifications
Tathmini ya matokeo
External plastering is carried out according to construction standards to protect and enhance the appearance of exterior walls
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain procedures for external plastering, including surface preparation, material mixing, and application techniques
Principles: The student should explain the principles involved in performing external plaster
Theories: The student should explain:-
- Importance of external plaster
- Surface preparation techniques
- Application of dots
- Tools and equipment
- Techniques for applying and floating
Swali
What is the primary purpose of external plastering (rendering) on building walls?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado