Mada za sehemu hiiPerforming architectural drawingsMada 3
- Drawing floor plans and foundation plans
- Drawing elevations
- Drawing sections
Drawing Sections
A section drawing is a vertical or horizontal cut through a building that reveals its interior structure. Imagine slicing through a loaf of bread — you can see the inside layers that were hidden from the outside. Similarly, a section drawing shows what lies inside walls, floors, and ceilings, including the materials used and how they are arranged.
For masons and bricklayers, section drawings are essential because they show the precise construction details that cannot be seen in floor plans or elevations. They reveal wall thicknesses, floor layers, roof construction, and how different building components fit together.
Section drawings provide information that floor plans and elevations cannot show. For example:
- A floor plan shows the layout of rooms, but it does not show how the floor is constructed or the thickness of each layer.
- An elevation shows the outside appearance of walls, but not what is inside them.
Sections clarify the inner components of a building, such as:
- Wall construction (brickwork, blockwork, insulation)
- Foundation and floor layers (hardcore, concrete, screed)
- Roof structure and ceiling details
- Relationship between different floor levels
Before drawing a section, you must first identify where the cut is made. This is shown on the floor plan using a section line.
- The section line is drawn as a thick dashed line with alternating long and short dashes.
- Arrows on the line indicate the direction in which the section is viewed.
- The section is labeled, for example, as "Section X-X" or "Section A-A."
When you look at the floor plan, you will see the section line passing through the part of the building you want to examine. The view you draw is what you would see if you stood at that line and looked inside the building.
The following procedure is used to draw a vertical section through a building:
1. Prepare the Drawing Sheet
- Secure drawing paper to the board using masking tape.
- Draw borderlines and a title block. Include your name, drawing title (such as "Section X–X"), date, and scale.
2. Draw the Ground Line
- Draw a horizontal line at the base of the drawing to represent the natural ground level.
3. Project the Walls
- From the section line on the floor plan, project vertical lines upward to represent the walls.
- Use the proper wall thickness (for example, 230 mm for a brick wall) and assume a wall height of typically 3 metres unless specified otherwise.
4. Draw Floor Layers
- Below the ground line, show the floor construction layers.
- For a typical floor, show: sand screed (15–25 mm), power-floated concrete (100–150 mm), and hardcore.
- Label each layer clearly.
5. Draw Door and Window Openings
- Where the section passes through door openings, show the door head height (usually 2.1 m from the finished floor level).
- Leave clear spaces to represent the openings.
6. Draw the Roof or Ceiling
- At the top of the section, draw a flat slab or ceiling line.
- If a roof is included, show the roof slope, thickness, and any overhangs.
- Assume a slab thickness (for example, 150 mm) if not indicated on the plan.
7. Apply Hatching
- Hatching (also called section lining) is applied at 45° to the cut surfaces to show which materials are exposed by the cut.
- Different materials have different hatching patterns. For example:
- Brickwork: diagonal parallel lines
- Reinforced concrete: scattered triangles
- Mass concrete: fine dots with scattered triangles
- Keep hatching evenly spaced and consistent.
8. Add Labels and Dimensions
- Label each room, floor materials, and structural components.
- Indicate the finished floor level (FFL).
- Write "SECTION X–X" clearly on the drawing.
- Add dimensions showing heights and layer thicknesses.
Worked Example: Drawing Section X–X Through a Genset Room
Suppose you are given a floor plan and asked to draw Section X–X through the Genset room. The floor plan shows the room dimensions as 3 metres by 4 metres.
Step 1: Calculate the scaled dimensions (using 1:50 scale).
- Room length: 4 m → 4 ÷ 50 = 0.08 m = 8 cm on drawing
- Room width: 3 m → 3 ÷ 50 = 0.06 m = 6 cm on drawing
Step 2: Draw the ground line and project walls upward to a height of 3 metres (6 cm at 1:50 scale).
Step 3: Below ground level, draw the floor layers:
- Hardcore: 150 mm → 3 mm on drawing
- Concrete slab: 100 mm → 2 mm on drawing
- Screed: 20 mm → 0.4 mm on drawing
Step 4: Show the door opening with head height of 2.1 m (4.2 cm at 1:50 scale).
Step 5: Apply 45° hatching to the brick wall sections and concrete slab.
Step 6: Label the drawing with "SECTION X–X," room name, material names, and dimensions.
- Section drawings reveal interior details that cannot be seen in floor plans or elevations.
- The section line on the floor plan shows where the cut is made and the direction of view.
- Use the same scale as the floor plan (commonly 1:50 or 1:100).
- Hatching at 45° distinguishes cut surfaces from other surfaces.
- Always label materials, room names, and dimensions clearly.
- Standard material symbols help identify construction materials quickly.
- Forgetting to include the ground line and floor layers below it.
- Using inconsistent scale between the floor plan and the section.
- Applying hatching in the wrong direction (must be 45°).
- Omitting labels for materials and finished floor levels.
- Drawing the section line in the wrong position on the floor plan.
In Tanzania, when a local contractor is building a house in Dar es Salaam or Arusha, they use section drawings to understand how the floor should be constructed below the ground level — showing the hardcore, concrete slab, and damp-proof course. This ensures the floor stays dry and durable, especially in areas with high water tables. Without this knowledge, a mason might construct a floor that absorbs moisture, leading to damage and costly repairs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Prepare drawing tools
- Gather Materials
- Prepare formats and title blocks
- Choose a Scale
- Select the cut location
- Mark the cut line
- Draw the base line
- Add interior elements
- Add doors and windows
- Detail structural components
- Add textures and materials
- Indicate dimensions
Tathmini ya matokeo
Sections are created as per engineering standards to provide a detailed view of the internal structure and relationships between different elements
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain the methods involved in drawing sections
Principles: The student should explain the principles involved in drawing sections
Theories: The student should explain:-
- Application of various geometrical lines
- Plane and solid geometry
- The application of various tools and equipment
- Building design
- Spatial
- Environmental design
Circumstantial knowledge: Detailed knowledge about:
- Safe handling of drawing instruments,
- Safe operation of drawing equipment
Swali
What is the primary purpose of a section drawing in architectural construction?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado