Mada za sehemu hiiConstructing complex furnitureMada 4
- Making armed and shaped chairs
- Making shaped table
- Making upholstered chair
- Making kitchen cabinet and cupboard
Making Armed and Shaped Chairs
An armchair (also called an armed chair) is a seating furniture piece designed for a single person, featuring armrests mounted on both sides to provide enhanced comfort and support for the arms. Armchairs are commonly found in living rooms, offices, waiting areas, and lounges for relaxation. They are available in both traditional and contemporary styles with various designs. Understanding how to construct an armchair is an essential skill in furniture making because it combines basic joinery techniques with comfort-focused design.
An armchair consists of several key structural components that work together to provide comfort, stability, and durability:
- Seat – The horizontal surface where a person sits
- Backrest – The vertical support for the back
- Armrests – The supports on both sides for resting the arms
- Legs – Four vertical supports that raise the chair off the floor
- Frame – The structural skeleton that holds all components together
Each part must be properly sized and joined to ensure the chair is stable and comfortable for use.
Standard dimensions for an armchair (British Standard) ensure ergonomic comfort and proper proportions. The following table presents the typical measurements:
| Component | Measurement (inches) | Measurement (mm) |
|---|---|---|
| Overall height | 36–40" | 910–1020 |
| Seat height | 18–20" | 460–510 |
| Seat width | 22–28" | 560–710 |
| Seat depth | 18–22" | 450–560 |
| Armrest height | 25–28" | 640–710 |
| Armrest width | 5–8" | 130–200 |
| Backrest height | 20–24" | 510–610 |
These dimensions may be adjusted slightly based on the intended user and specific design requirements, but maintaining proper proportions is essential for comfort.
The following materials are needed to make an armchair:
- Wood: Hardwoods (such as mvule/teak, mninga), softwoods (such as pine), or plywood for the frame and components
- Wood glue: For securing joints
- Screws or nails: For fastening components
- Dowels or biscuits: For reinforced joinery
- Sandpaper: Various grits (80–220) for smoothing surfaces
- Wood stain or paint: For colour and finish
- Varnish, lacquer, or oil: For protecting the wood surface
- Wood filler: For filling gaps or imperfections
- Cushioning: 3–5 cm thick high-density foam for seat and backrest
- Fabric: 2–3 metres of durable cotton or polyester fabric for upholstery
The following tools and equipment are required for making an armchair:
- Measuring tape, T-square, pencil
- Tenon saw, hand saw, circular saw
- Bench planes, belt sander, thickness planer, surface planer
- Moulding machine, mortising machine
- Brace/hand drill, wood lath
- Chisel, mallet, hammer
- Templates for marking shapes
- Safety gear: overall, safety boots, mask, safety glasses
Step 1: Preparation of Materials
Prepare all materials by cutting the wood to the following sizes (as specified in the textbook):
- Seat: 50 cm × 45 cm (one piece)
- Backrest: 50 cm × 45 cm (one piece)
- Legs: 15–20 cm tall (four pieces)
- Armrests: 25 cm tall × 50 cm long (two pieces)
Also prepare cushioning foam (3–5 cm thick) and fabric (2–3 m).
Step 2: Sketching and Shop Drawings
Draw a detailed sketch of the chair and label all measurements. Produce shop drawings that show exactly how each piece will be cut and assembled. This planning step ensures accuracy during cutting and helps avoid mistakes.
Step 3: Cutting the Wood
Using a saw (hand saw or circular saw), cut the wood pieces according to the planned sizes shown in the shop drawings. After cutting, use sandpaper to smooth all surfaces and remove sharp edges.
Step 4: Assembling the Frame
Assemble the chair frame in the following order:
- Attach legs to the seat – Secure the four legs to the underside of the seat
- Fix the backrest – Position the backrest at a slight angle (usually 5–10 degrees) for ergonomic support
- Attach armrests – Fix the armrests to the sides of the seat and backrest
Ensure all joints are tight and the chair does not wobble. Use wood glue together with screws or dowels for strong joints.
Step 5: Adding Cushioning and Upholstery
- Cut foam to fit the seat and backrest dimensions
- Wrap each foam piece with fabric
- Staple the fabric underneath the cushion edges to secure it and prevent wrinkles
- Ensure the fabric is stretched evenly without sagging
Step 6: Finishing
Apply wood stain, paint, varnish, or oil to the wooden parts for protection and appearance. Add decorative elements such as nails or buttons according to the design.
Step 7: Cleaning and Storage
Clean the working area and all tools. Store tools properly in their designated places for future use.
Suppose you want to make an armchair with the following dimensions:
- Seat: 50 cm × 45 cm
- Backrest: 50 cm × 45 cm
- Legs: 18 cm tall (4 pieces, assume 4 cm × 4 cm cross-section)
- Armrests: 25 cm tall × 50 cm long (2 pieces, assume 5 cm × 8 cm cross-section)
Calculating total wood volume needed:
- Seat board: 50 cm × 45 cm × 2.5 cm = 5,625 cm³
- Backrest board: 50 cm × 45 cm × 2.5 cm = 5,625 cm³
- Four legs: 4 × (4 cm × 4 cm × 18 cm) = 1,152 cm³
- Two armrests: 2 × (5 cm × 8 cm × 25 cm) = 2,000 cm³
Total ≈ 14,402 cm³ (approximately 0.0144 m³)
This calculation helps in estimating the amount of timber to purchase from a local hardware store.
When constructing an armchair, perform the following quality checks:
- Stability test: Gently rock the chair to ensure no wobbling
- Joint integrity: Check that all joints are tight and properly glued
- Surface smoothness: Run hands over all surfaces to feel for splinters or rough areas
- Dimensions accuracy: Verify measurements against the design specifications
- Upholstery condition: Ensure fabric is evenly stretched with no wrinkles or loose staples
| Problem | Possible Cause | Solution |
|---|---|---|
| Chair wobbles | Legs uneven or joints loose | Adjust leg lengths or tighten joints |
| Fabric wrinkles | Fabric not stretched evenly | Re-staple fabric starting from centre |
| Wood splits | Pre-drilled holes not used | Always drill pilot holes before inserting screws |
| Uneven finish | Surface not properly sanded | Sand again starting with lower grit |
- Always wear safety boots, mask, and safety glasses when working
- Use proper lifting techniques when moving wood pieces
- Keep fingers away from saw blades and drill bits
- Secure workpiece properly before cutting or drilling
- Work in a well-ventilated area when applying finishes
In Tanzania, the skill of making armchairs is valuable for small furniture businesses in towns like Arusha, Mwanza, and Dodoma, where customers often order custom-made seating for homes, offices, and guesthouses. For example, a carpenter in Dar es Salaam could make a simple armchair using local mvule (teak) wood and sell it for approximately TZS 250,000–400,000, earning a good income while meeting the demand for affordable, locally made furniture.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Draw furniture
- Interpret drawings
- Calculate materials required
- Select tools and materials
- Prepare members
- Set out members
- Make joints
- Assemble members
- Perform general finishing
- Apply finishes
- Clean work place tools and machines
- Store tools at safe place
- Store furniture at safe place
Tathmini ya matokeo
Armed shaped chair conforms to drawing and technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The students should describe how to make armed shaped chairs
Principles: The student should state principles related to making armed shaped chairs
Theories: The students should explain the uses of armed shaped chairs
Circumstantial knowledge: Workshop safety rules and regulations
Swali
According to the British Standard, what is the typical seat height range for an armchair?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado