Mada za sehemu hiiPerforming wood turningMada 2
- Performing face plate
- Performing spindle turning
Spindle turning is a woodworking technique where a piece of wood spins on a lathe while a sharp cutting tool shapes it into round, symmetrical objects such as table legs, stool legs, or decorative pieces. The wood grain runs parallel to the lathe bed in spindle turning, distinguishing it from faceplate turning where the grain runs perpendicular to the lathe bed.
Lathes used for wood turning are classified into two main types:
- Bench-mounted lathe machines – Smaller lathes that sit on a workbench, suitable for small workshop projects
- Frame-mounted lathe machines – Larger, heavier lathes mounted on a permanent frame, suitable for bigger workpieces
Both types perform spindle turning when the workpiece grain runs parallel to the lathe bed.
Before performing spindle turning, you must observe these safety rules:
- Wear correct dress: remove rings, watches, and roll sleeves above elbows
- Switch off the lathe when checking job size or making adjustments
- Stand to one side when switching the lathe on
- Keep the workshop neat and free from obstacles
- Ensure the workpiece is free from splits and knots
- Mount the job tightly on the lathe between centres
- Check that the workpiece rotates freely before starting
- Keep tools sharpened and stored in a safe place
- Adjust the tool rest close to the workpiece (within 3 mm) and to the correct height
- Check the rotation direction of the work before starting
The following PPE must be worn during spindle turning:
- Cap – protects head from wood dust
- Goggles – safeguard eyes from flying wood chips and dust
- Nose mask – protects lungs from wood dust
- Safety shoes – protect feet from falling chisels due to vibration
- Leather apron – safeguards the body from sharp wood scraps
Different chisels serve different purposes in spindle turning:
| Chisel Type | Purpose |
|---|---|
| Gouge chisel | Sharpened on the convex outside surface; used for cutting rough surfaces quickly, turning work from square to round. Sizes: 6 mm to 40 mm |
| Skew chisel | Sharpened on both surfaces; used for V-shaped grooves, taper turning, cutting beads, and making smooth surfaces. Sizes: 6 mm to 40 mm |
| Parting tool | Narrow blade; used for making deep cuts, separating workpieces, and creating shoulder cuts. Sizes: 6 mm to 8 mm |
| Round nose chisel | Sharpened on one side only; used for forming hollow or concave surfaces. Sizes: 6 mm to 20 mm |
| Spear point chisel | Sharpened on one side only; used for scraping beads, squaring ends, and producing flat surfaces. Sizes: 6 mm to 20 mm |
| Flat or facing chisel | Thicker than other chisels; used for scraping cylinders, beads, and surface work |
Step 1: Preparation and Setting Up
Proper setup makes the work easier and enjoyable:
- Set up the working space in a well-ordered condition
- Inspect the lathe machine and sharpen all tools before starting
- Position tools and abrasives within easy reach
- Ensure the grinder for sharpening is no more than a few steps away
- Set good ambient lighting using a strong adjustable lamp
- Align the centres and stabilise the lathe
- Locate belts and switches for easy access
- Tune the tool rest to the correct height and angle
Step 2: Locating the Centre
Before mounting the workpiece, find its centre accurately:
- For a square spindle blank, draw lines from corner to corner (diagonals)
- Where a corner is missing, draw lines parallel to the sides, then draw diagonals within the resulting square or rectangle
- A centre finder can quickly locate the centre on spindle blanks and cylinders
- For larger diameter face work, use templates for layout
Step 3: Laying Out Spindles
- Batches of similar spindles can be marked either on or off the lathe
- Single spindles or legs with square sections are most conveniently marked on a workbench
- To copy a single spindle without square sections, reduce your blank to a cylinder first, then hold the spindle against the cylinder and mark the details
- Use a story stick to transfer measurements accurately
Step 4: Preparing the Blank
- Square spindle blanks are most accurately sawn to size on a table saw using a fence
- Traditionally, spindle blanks are split from small logs, then roughly shaped using an axe
- Ensure the blank is free from splits, knots, and defects
Step 5: Mounting the Workpiece
- Blanks with grain running parallel to the lathe axis are mounted between a spur drive centre and a tail centre
- Locate the spur drive end first, then fix the tail centre to support the other end
- The spur drive must bite into the wood securely
- Check that the workpiece rotates freely before starting
Step 6: Roughing Down the Blank
- Use a large gouge called a "roughing out gouge" to turn a square blank into a rough cylinder
- This removes the bulk of the waste material quickly
- Work from tailstock towards headstock
Step 7: Planning Cut (Smoothing)
- The planning cut is analogous to using a smoothing plane in general woodwork
- Use a skew chisel to produce a good surface that requires little sanding
- This step follows immediately after roughing down
Step 8: Making V Cuts
- A V cut creates a V-shaped depression in the workpiece
- This cut may be made for decoration, or as the first step in cutting a bead
- Use a skew chisel to form the V shape
Step 9: Forming a Bead
- A bead is a decorative feature running round a piece of turning
- It is roughly semicircular in cross-section, standing like a hill
- Use a skew chisel or gouge to form the bead profile
Step 10: Forming a Cove
- A cove is the opposite of a bead
- It is also roughly semicircular in cross-section but forms an indentation like a valley
- Use a gouge or skew chisel to cut the concave profile
Step 11: Blending Beads and Coves
- The profile of a true bead or cove approximates to an arc of a circle
- Often they approach the full semicircle but not always
- Practice blending multiple beads and coves for smooth transitions
- These are often applied as decorations on furniture legs
Step 12: Squaring the End
- Use a skew chisel held vertically to square the end of the workpiece
- Support the handle of the chisel firmly
- Make light cuts to achieve a clean square shoulder
Step 13: Rounding the End
- Similar to cutting a large bead, but considered as a separate exercise
- Useful when making table or stool legs where the end must be completely round
- Use smooth, controlled movements with a skew chisel
Step 14: Cutting Pummels
- When making items such as table or stool legs, sections of the workpiece may need to remain in the original square condition
- The section left square is called a pummel
- This creates a transition from the square section to the round section
A student at VETA Mwanza needs to make four identical stool legs, each 305 mm long. The leg design has a round top section with a tenon, a decorative bead, a pummel (square section), and a tapered bottom.
Procedure followed:
- Mount the blank between centres on the lathe
- Turn the top tenon first using callipers set to 20 mm diameter
- Mark details using a story stick to ensure all four legs are identical
- Roughing: Use a roughing gouge to turn the blank from square to round
- Smoothing: Use a skew chisel for planning cut
- Form beads: Use skew chisel to form decorative beads
- Leave pummels: Keep some sections square as required by design
- Taper the bottom: Use a skew chisel to create the taper
- Check with callipers at each stage to maintain uniformity
The callipers are used by opening them to the required measurement and sliding across the spinning workpiece to check diameter at any point.
In Tanzania, spindle turning skills are valuable for local carpentry workshops that produce furniture such as tables, chairs, and stools for homes and hotels. A young entrepreneur in Arusha can use spindle turning to produce decorative table legs and chair spindles for sale at local markets, charging approximately TSh 15,000–25,000 per finished leg, thereby earning income while applying woodworking skills learned at VETA.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Prepare drawing for wood turning
- Interpret drawings
- Calculate materials required
- Select tools and materials
- Prepare materials
- Fix work piece
- Perform turning
- Perform finishing
- Clean work place and tools
- Store work piece and tools at safe place
Tathmini ya matokeo
Spindle turning conforms to drawing and technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The students should describe how to perform spindle turning
Principles: The student should state principles related to performing spindle turning
Theories: The students should explain importance of performing spindle turning
Circumstantial knowledge: Workshop safety rules and regulations
Swali
Which of the following lathes can be used to perform spindle turning?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado