Mada za sehemu hiiPerforming timber preparationMada 2
- Performing sawing
- Performing planing
Planing is the process of smoothing and flattening timber surfaces using a hand plane. It removes small amounts of wood to create a flat, even, and smooth surface ready for joining or finishing in furniture making.
Planing serves several important purposes:
- Removes rough marks, saw cuts, and irregularities left by other tools
- Creates flat and true surfaces for accurate joints
- Reduces timber thickness to required dimensions
- Produces a smooth surface ready for painting, varnishing, or polishing
- Ensures timber pieces fit together properly when joining
Timber is planed in different ways depending on the job:
-
Planing along the grain – The normal method. The plane is pushed along the length of the timber in the direction in which the wood fibres rise away from the cut ("with the grain"). Planing the other way tears the fibres.
-
Planing across the grain – The plane is pushed straight or diagonally across a wide board that is hollow or twisted, to take off the high parts quickly. The surface is then finished along the grain.
-
Planing end grain – Used to make the end of a piece clean and square. Take very thin shavings with a sharp blade and plane from each edge towards the middle, so that the far corner does not split off.
Timber is always prepared in the same order: face side, face edge, width, thickness, and then it is cut to length.
The following tools and equipment are needed for planing:
| Tool | Purpose |
|---|---|
| Jack plane | Main tool for general planing |
| Hand saw | Cutting timber to size before planing |
| Marking gauge | Marking lines for accurate planing |
| G clamp | Holding timber firmly to the workbench |
| Try square and straight edge | Checking squareness and flatness |
| Broom and dust covers | Cleaning up and covering finished work |
Safety gear (PPE):
- Overalls (protective clothing)
- Safety goggles (eye protection)
- Dust mask (protection from wood dust)
Before starting any planing work, always:
- Wear protective clothing and safety gear
- Ensure the timber is securely clamped to the workbench
- Check that the plane blade is sharp and properly adjusted; never test sharpness by running a finger along the edge
- Keep both hands on the plane, behind the cutting edge, while planing
- Lay the plane on its side on the bench when you put it down, so that the blade is not damaged and nobody is cut
- Keep the work area clean and free of wood shavings
- Work in a well-ventilated area to avoid inhaling dust
Step 1: Prepare the Timber
- Cut the timber a little longer than the finished length (about 20 mm extra) using a hand saw
- Check the required length, width and thickness on the drawing or cutting list
- Hold the timber firmly: push it against the bench stop or grip it in the vice. If a G clamp is used, place it where the plane will not strike it
Step 2: Inspect and Set Up the Jack Plane
- Check that the plane blade projects only very slightly below the sole, about the thickness of a sheet of paper. Sight along the sole from the front: the cutting edge should show as a thin, even, dark line. Adjust the depth and level the blade before starting
- Ensure the blade is sharp and free from damage
- Hold the plane with one hand on the handle and the other on the front knob
Step 3: Plane the Face Side
- Choose the better wide surface as the face side, and look at the edge of the timber to see which way the grain runs
- Plane along the grain with long, even strokes. Press down on the front knob at the start of each stroke and on the handle at the end, so that the ends are not rounded off
- Lift the plane slightly on the return stroke
- Check that the surface is flat with a straight edge held along it, across it and from corner to corner; light showing under the straight edge marks a hollow
- Check for twist by sighting across two winding sticks (two straight strips of wood), one placed at each end
- When the surface is straight and flat, pencil the face side mark on it
Step 4: Plane the Face Edge
- Grip the timber in the vice with the better edge upwards
- Plane the edge straight along its length
- Check straightness with a straight edge, and check squareness by holding the stock of a try square against the face side at several places
- When the edge is straight and square to the face side, pencil the face edge mark on it
Step 5: Gauge and Plane to Width and Thickness
- Set the marking gauge to the required width. Press its stock against the face edge and gauge a line along both faces
- Plane the opposite edge down to the gauge lines and check that it is square
- Set the marking gauge to the required thickness. Press its stock against the face side and gauge a line along both edges
- Plane the second face down to the gauge lines
- For the last few strokes, set the blade finer and take thin shavings along the grain to leave a smooth surface
Step 6: Check and Cut to Size
- Use a straight edge to verify that each surface is flat and straight
- Use a try square to check that the edges are square to the faces
- Measure the width and thickness with a rule
- Square a line round the timber at the finished length and saw off the waste
- The surfaces should be smooth, flat, and free from tear-out
Step 7: Clean Up
- Sweep up wood shavings and dust
- Brush the shavings out of the plane, draw the blade back, wipe the sole with a lightly oiled rag and store the plane on its side in a dry place
- Stack the finished workpiece flat, marked with your name, and cover it with a dust cover
- Return all tools to their proper locations
- Dispose of waste material properly
A carpenter needs to prepare a timber board for a table leg. The board measures 75 mm wide but needs to be 70 mm wide.
- After planing the face side and face edge, the carpenter sets a marking gauge to 70 mm and gauges a line from the face edge along both faces
- He grips the board in the vice with the unplaned edge upwards
- Using the jack plane, he trims along the length of the grain, removing wood up to the marked line
- He checks with a try square to ensure the edge is square
- Finally, he smooths the surface with fine passes of the plane
The result is a clean, square, smooth surface ready for joining to other table components.
- Applying too much pressure, which causes uneven cuts
- Planing against the grain, which causes tear-out
- Using a dull blade, which produces rough surfaces
- Failing to clamp timber securely, which is dangerous
- Skipping the inspection of the plane before use
A carpenter in Arusha uses planing skills when building a wooden bed frame for a customer's home. After cutting the timber to length with a saw, he planes all the surfaces flat and smooth before assembling the frame. The smooth surfaces ensure the joints fit tightly and the bed frame is comfortable and safe to use. This same skill is used by local furniture makers throughout Tanzania to create quality wooden furniture sold in markets and shops.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Plane face side straight and flat
- Plane face edge straight and square to face side
- Gauge the thickness
- Gauge the width
- Check/control levelness, squareness and straightness
- Cut to required size
- Clean work place
- Store work piece and tools
Tathmini ya matokeo
A prepared work piece for planing conforms to the given technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain methods related to perform planing
Principles: The student should explain principles related to perform planing
Theories: The students should explain theories related to perform planing
Circumstantial knowledge: The students should explain detailed knowledge related to perform planing
Swali
Which of the following is a purpose of planing timber in furniture making?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado