Mada za sehemu hiiPerforming timber preparationMada 2
- Performing sawing
- Performing planing
Sawing is one of the most fundamental timber preparation skills in carpentry. It involves using a saw to cut timber along or across the grain to produce pieces of the required size and shape.
- Hand saw – the most common tool for general sawing work
- Tenon saw – used for fine, accurate cuts
- Dovetail saw – used for very fine joinery work
- Crosscut saw – designed specifically for cutting across the grain
- Ripsaw – designed for cutting along the grain
Saw teeth are bent slightly to the left and to the right in turn. This is called the set. It makes the cut (the kerf) a little wider than the blade so that the saw does not jam in the timber. A sharp, correctly set saw cuts easily and safely; a blunt saw has to be forced and is more likely to slip.
- Cross-cutting – cutting timber across the grain (perpendicular to the wood fibres)
- Ripping – cutting timber along the grain (parallel to the wood fibres)
- Angled cutting – cutting timber at an angle to the face
Timber for furniture is prepared in a fixed order, and sawing is used at the start and at the end:
- Saw the rough timber a little longer and wider than the finished size.
- Plane the face side straight and flat with a jack plane.
- Plane the face edge straight and square to the face side.
- Set a marking gauge and gauge the width from the face edge, then plane down to the line.
- Gauge the thickness from the face side and plane down to the line.
- Check that the piece is flat, straight and square with a straight edge and a try square.
- Mark the finished length with a try square and saw to the required size.
- Mark the cutting line on the timber. For a cut across the grain, measure with a rule and draw the line with a pencil against a try square, on the face and down both edges. For a cut along the grain, use a marking gauge or a rule and straight edge.
- Secure the timber firmly in a vice or using a G-clamp on a workbench.
- Position yourself correctly – stand so that your sawing arm, shoulder and eye are in line with the cut, with the opposite foot slightly forward (the left foot for a right-handed person).
- Start the cut – hold the saw with your dominant hand and place the thumb of your other hand against the blade as a guide. Keep the thumb above the teeth, against the flat of the blade, and move the hand away as soon as the groove is started.
- Begin with 2–3 backward strokes gently to create a groove (kerf) on the waste side of the line.
- Continue with long, steady strokes – let the saw do the work; do not press down heavily. Hold a hand saw at about 45° to the surface for cutting across the grain and at about 60° for cutting along the grain.
- Keep the blade aligned with the marked line throughout the cut.
- Support the offcut as you near the end to prevent the wood from splintering.
- Finish the cut with light strokes, then check the length with a rule and check that the sawn end is square with a try square.
- Wear safety goggles to protect your eyes from wood chips.
- Use a dust mask when sawing to avoid inhaling sawdust.
- Ensure the timber is securely clamped before sawing.
- Once the cut is started, keep your free hand well away from the line of the saw.
- Carry a saw by the handle with the blade pointing down, and never leave it lying where its teeth can be damaged or can cut someone.
- Wear a close-fitting overall and keep loose sleeves out of the way.
- Keep the workshop floor clean and free of sawdust and offcuts.
A carpenter needs to cut a piece of timber to make a stool leg. The timber measures 80 cm long, but the leg must be 60 cm long.
- Measure and mark 60 cm from one end using a ruler and pencil.
- Square the line across the face and down both edges using a try square and pencil, and mark the waste side with a cross.
- Secure the timber in a vice on the workbench with the cutting line clear of the jaws.
- Using a hand saw, make the cut just outside the marked line on the waste side.
- Result – the finished piece measures 60 cm as required, ready for smoothing with a jack plane.
| Fault | Cause | Prevention |
|---|---|---|
| Uneven cut | Pressing too hard or twisting the saw | Use long, steady strokes |
| Splintering at the end of the cut | Offcut not supported; heavy strokes at the finish | Support the offcut and finish with light strokes |
| Piece cut too short | Sawing on the line or on the wrong side of it | Always cut on the waste side of the line |
| Curved cut | Not following the line | Keep your eye on the line throughout |
| Saw jams in the cut | Kerf closing on the blade, or a blunt saw | Support the timber so that the kerf stays open; use a sharp saw |
- Brush the sawdust off the bench and sweep the floor with a broom; sawdust on the floor is slippery and is a fire risk.
- Put useful offcuts in the offcut box and waste in the bin.
- Wipe the saw blade clean, rub it with a lightly oiled rag to prevent rust, and hang the saw up or put it in the rack with its teeth protected.
- Return the G clamp, marking gauge and try square to their places.
- Mark your workpiece with your name, stack it flat so that it does not twist, and put dust covers over finished work.
In Tanzania, a student who masters sawing can help their family build useful furniture such as stools, small tables, or shelves using locally sourced timber. A carpenter in Arusha or Mwanza might use these same skills to cut timber to size for custom furniture orders, earning income by producing accurately cut pieces for customers in their community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Plane face side straight and flat
- Plane face edge straight and square to face side
- Gauge the thickness
- Gauge the width
- Check/control levelness, squareness, and straightness
- Cut to required size
- Clean work place
- Store work piece and tools
Tathmini ya matokeo
A workpiece of sawn timber conforms to the given technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain methods related to perform sawing
Principles: The student should explain principles related to perform sawing
Theories: The student should explain theories related to perform sawing
Circumstantial knowledge: The students should explain detailed knowledge related to perform sawing
Swali
What is the narrow groove cut by a saw blade in timber called?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado