Mada za sehemu hiiPerforming timber treatmentMada 2
- Timber seasoning
- Timbering treatment
Timber Treatment
Timber treatment is the process of preserving timber so that it can withstand weather conditions and resist damage from fungi and insects. The main purpose is to extend the useful life of timber by protecting it from decay, rot, and insect attack. When timber is properly treated, it becomes more durable and suitable for various construction purposes in Tanzania's climate.
Timber treatment is done to achieve several important objectives:
- Protection from weathering – Prevents erosion and discolouration caused by sun, rain, and wind
- Resistance to sunlight – Reduces damage from UV rays that break down the wood surface
- Control of moisture movement – Minimizes warping, cracking, and splitting when timber gets wet and dry
- Prevention of biological attack – Stops fungi and insects from destroying the wood
Timber should be adequately seasoned (dried) before treatment with a preservative for the best results. It is important to note that timber with moisture content below 20% is generally safe from fungal attack.
Timber can be treated using two main categories of methods: pressure methods and non-pressure methods.
Pressure Methods
In pressure methods, timber is placed in a sealed chamber where preservative is forced into the wood under pressure. There are three main types:
1. Full-cell process The chamber is sealed and air is removed using a vacuum pump. Preservative is then introduced while still under vacuum. After the timber absorbs sufficient preservative, pressure is released and excess preservative is pumped out. This process is commonly used with creosote or water-borne preservatives.
2. Empty-cell (Lowry) process Preservative is pumped into the chamber at normal air pressure. After the wood absorbs enough preservative, pressure is released and the expanding air drives out surplus preservative from the wood cells. A vacuum then removes any residue. The cell walls remain treated even though the cavities are emptied.
3. Double-vacuum process A partial vacuum is created first, then the chamber is filled with preservative and pressurized. After a set time, it is drained and a final vacuum removes excess preservative. This process is mainly used for organic solvent preservatives on exterior joinery. It does not cause timber to swell or distort.
Non-pressure Methods
These methods do not use pressure to force preservative into the timber:
1. Immersion/Dipping The timber is submerged in a tank of preservative for a short period, then allowed to drain. This is suitable for coal-tar oils or organic solvent types.
2. Steeping The timber is submerged for periods ranging from a few hours to several weeks, depending on the wood species, size, and intended use. This method is suitable for preserving fence posts.
There are three main categories of materials used to treat timber:
Paints and Varnishes
Exterior-quality paints and varnishes protect timber from:
- Entry of water
- Abrasive particles (grit and dirt)
- Solar radiation and discolouration
Correctly painted surfaces can give protection for up to five years if:
- The timber is thoroughly dry before application
- Surfaces are prepared correctly
- The manufacturer's recommended number of coats is applied
Water-repellent Exterior Stains
These provide a clear or coloured, matt or semi-gloss, water-repellent surface that allows the wood grain to show through. They can protect timber for up to four years or more. A key advantage is that they allow the wood to breathe, letting trapped moisture escape.
Preservatives
Preservatives protect timber from insects and fungi. There are three main types:
1. Organic-solvent preservatives Use organic solvents to carry toxic chemicals into the wood. After application, solvents evaporate leaving the wood toxic to insects and fungi. Applied by brushing or low-pressure processes.
2. Water-borne preservatives Use water to convey toxic chemicals. These are non-flammable, but drying is necessary after treatment. Dry treated timber can be painted over.
3. Tar-oil preservatives Derived from coal tar, ideal for exterior work not to be painted. The most common form is creosote, which is light to dark brown in colour. It has a strong odor after application but provides excellent protection.
When performing timber treatment, always observe the following safety measures:
- Wear protective gloves and overalls
- Use safety boots
- Wear a dust mask when sanding or handling treated timber
- Ensure good ventilation in the working area
- Use dust covers to protect surrounding areas
- Clean materials after treatment work
A carpenter in Dodoma has a batch of Eucalyptus timber posts that will be used for fence construction. The timber was cut fresh and has not been seasoned. The carpenter decides to treat the timber using the steeping method (a non-pressure method).
Calculate the moisture content after treatment if:
- Wet weight of a sample post = 45 kg
- Dry weight after proper seasoning = 36 kg
Solution:
MC%=(mdrymwet−mdry)×100
MC%=(3645−36)×100
MC%=(369)×100
MC%=0.25×100=25%
The moisture content is 25%. This is still above the safe level of 20% for preventing fungal attack, so the timber should be further seasoned before applying preservative treatment.
In Tanzania, a small-scale carpentry business in Mwanza that makes doors, window frames, and furniture can apply timber treatment knowledge to improve product quality. For example, when a customer orders outdoor timber furniture or roof trusses, the carpenter can treat the timber with preservative using the steeping method to protect against fungal decay and insect attack, ensuring the furniture lasts longer in the humid rainy season while charging a premium price for the added durability.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Prepare tools and materials
- Preserve timbers
- Dry timbers
- Store timbers
- Clean work place
- Store tools
Tathmini ya matokeo
Treated timber conform to technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should b able to explain methods related to timber treatment
Principles: The student should explain principles related to timber treatment
Theories: The students should explain theories related to timber treatment
Circumstantial knowledge: The students should explain detailed knowledge related to timber treatment
Swali
What is the main purpose of timber treatment?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado