Mada za sehemu hiiMaking corner framesMada 2
- Making notice board frames
- Making picture frames
A notice board frame is a wooden border designed to hold a notice board on a wall for displaying public messages such as advertisements, event announcements, or general information. In this lesson, you will learn the parts of a notice board frame, the materials and tools required, and the step-by-step procedure for making one in the workshop.
A notice board frame is a framework constructed from wood (or other materials like metal or plastic) that holds and protects a backing board where notices can be pinned or attached. The frame provides the structure needed to mount the board on a wall and gives it a neat, finished appearance. Notice boards are commonly used in schools, offices, community centres, and markets to share information with groups of people.
Understanding each part helps you select the right materials and assemble the frame correctly:
- Frame — The outer border that holds all components together. It is typically made from timber and comes in various styles and finishes.
- Backing board — The core component where notices are pinned. Common materials include cork, foam board, or fabric-covered board.
- Glass or acrylic cover — A transparent protective layer that keeps notices visible while protecting them from dust and damage.
- Hinges — Allow a cover (if present) to open and close while remaining attached to the frame.
- Mounting hardware — Brackets, screws, or hooks used to attach the notice board to a wall.
- Edges or trim — Additional strips around the edges that improve appearance and provide protection.
- Fasteners or clips — Devices that hold notices without pins, integrated into the frame design.
- Feet or stand — Used for freestanding notice boards to keep them upright.
Materials
- Timber (for frame members)
- Wood glue
- Wire nails or screws
- Sandpaper (various grades)
- Sanding sealer and thinner
- Wood filler
Tools and Equipment
- Measuring tape
- Pencil or marking knife
- Try square
- Hand saw or tenon saw
- Jack plane
- Rebate plane
- Claw hammer
- Screwdriver
- Mortise chisel
- Hand drill
- Paintbrush
- Workbench with vice
- Marking gauge
- Mitre saw machine (if available)
Follow these steps in order to create a properly aligned and sturdy notice board frame:
Step 1: Wear Personal Protective Equipment (PPE)
Before starting, put on safety gear including safety glasses, ear plugs, and gloves. This protects you from flying wood chips, loud tool noise, and potential injuries.
Step 2: Select and Check Materials
Choose timber pieces that are free from defects such as cracks, knots, or warping. Determine the thickness and width of frame pieces based on the required dimensions of the notice board.
Step 3: Measure and Cut Pieces
Measure the length and width of each frame member according to the working drawing. Use a try square to ensure accurate 90-degree cuts when cutting with a hand saw.
Step 4: Plane Wood Face Side
Plane the face side of each timber piece to create a flat and straight surface. This serves as the reference surface for all other planing operations.
Step 5: Plane Wood Face Edge
Plane the face edge to get correct edges for width. The face edge must be straight and square to the face side.
Step 6: Plane Wood for Required Thickness
Plane each piece to achieve the thickness specified in the technical drawing or as required for the frame design.
Step 7: Rip Wood to Get Required Width
Rip (cut along the grain) the timber pieces to obtain the required width for each frame member using a hand saw or tenon saw.
Step 8: Cut Rebate
Cut a rebate (groove) along the inner edge of each frame piece to accommodate the backing board, glass, or acrylic cover. The rebate size should match the thickness of these components.
Step 9: Set Out and Cut Mitre Joint
Mark the mitre joint positions on the ends of each frame member. A mitre joint is cut at 45 degrees so that two pieces meet to form a 90-degree corner. Set out carefully using a marking gauge and pencil.
Step 10: Dry Assemble to Check Fit
Assemble the frame pieces without glue or nails to check that all joints fit properly. Make any necessary adjustments before final assembly.
Step 11: Sand All Pieces
Sand each piece starting with rough sandpaper (course grade) and progress to fine sandpaper for a smooth finish. Sand along the grain direction.
Step 12: Assemble the Frame
Apply wood glue to the joint surfaces if desired for added strength. Secure the frame pieces together using nails or screws. Ensure corners are tight and properly aligned.
Step 13: Check for Square
Use a try square to verify that all corners are exactly 90 degrees. If the frame is not square, adjust the joints before the glue sets.
Step 14: Fill Gaps and Finish
Fill any gaps, nail holes, or imperfections with wood filler. Once dry, sand the frame smoothly. Apply undercoat paint or stain as desired, then allow it to dry completely.
Step 15: Clean the Workplace
Remove all wood shavings and debris. Return all tools to their proper storage locations.
Suppose you need to make a notice board frame for a classroom in Arusha that will be 60 cm wide and 45 cm tall. The frame pieces should be 3 cm wide and 1.5 cm thick.
Calculation:
- For the width (horizontal pieces): 60 cm + (2 × 3 cm rebate allowance) = 66 cm each → cut 2 pieces at 66 cm
- For the height (vertical pieces): 45 cm + (2 × 3 cm rebate allowance) = 51 cm each → cut 2 pieces at 51 cm
Each end of all four pieces must be cut at a 45-degree mitre so that when assembled, they form neat 90-degree corners.
Always observe safety when making a notice board frame:
- Wear PPE at all times — safety glasses, ear plugs, and gloves.
- Use tools properly and for their intended purpose only.
- Keep the workshop clean and organized to prevent trips and cuts.
- Secure timber pieces with a bench vice or bench hook before cutting or planing.
- Ensure good ventilation when applying paint, stain, or wood sealer.
In Tanzania, you can apply these skills to make notice boards for your school, church, or local market. For example, a small business owner at Mnazi Mmoja market in Dar es Salaam could have you make a custom notice board frame for displaying price lists and advertisements, helping them attract customers while keeping information organized and protected from dust.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Draw corner frames
- Interpret drawings
- Calculate materials required
- Select tools and materials
- Take correct measurements
- Prepare member to the specified measurements
- Set out corner joints
- Make joints
- Assemble the frame
- Apply finishes
- Clean the work area
- Store the frame and tools in a safe place
Tathmini ya matokeo
The constructed notice board conforms to drawing and technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain methods related to making notice board frames
Principles: The student should be able to explain principles related to making notice board frames
Theories: The students should be able to explain theories related to making notice board frames
Circumstantial knowledge: The students should explain detailed knowledge related to making notice board
Swali
Which of the following is NOT a part of a notice board frame?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado