Mada za sehemu hiiInstalling control system of AC machinesMada 7
- Installing DOL starter incorporating remote control
- Installing DOL by using the jogging method
- Installing forward and reverse starter
- Installing manual star-delta starter
- Installing automatic star-delta starter
- Installing a rotor resistance starter for the slip-ring motor with automatic starting
- Installing a rotor resistance starter for the slip-ring motor
A rotor resistance starter is a device used to start slip-ring (ship-ring) induction motors by connecting external resistors to the rotor circuit through slip rings. Unlike squirrel-cage motors, slip-ring motors have their rotor windings connected to external circuits via slip rings, allowing us to add resistance during starting.
The "automatic starting" part means the starter automatically removes the external resistance once the motor reaches a certain speed, bringing the motor to normal running conditions.
When a large induction motor starts directly on full supply voltage, it draws a very high starting current (often 5 to 7 times the normal running current). This causes problems:
- Low starting torque — the motor may struggle to start under load
- Voltage drop — other equipment connected to the same supply may be affected
- Mechanical stress — sudden starting can damage the motor and connected machinery
By adding resistance to the rotor circuit at startup:
- Starting current is reduced — the total impedance of the motor increases
- Starting torque increases — this is a key advantage of slip-ring motors
- Smooth acceleration — the motor accelerates gradually under load
The rotor windings of a slip-ring motor are connected to three slip rings on the motor shaft. During starting, external resistors (usually three-phase rheostats) are connected to these slip rings through carbon brushes.
At startup:
- Maximum resistance is inserted into the rotor circuit
- This limits the starting current while maximizing starting torque
As the motor speeds up:
- The starter automatically (or manually) reduces the resistance
- At normal running speed, the rotor is short-circuited (resistance = 0)
Step 1: Preparation and Safety
Before installation, ensure:
- The motor is isolated from the power supply (lock out, tag out)
- All safety gear is worn: safety boots, safety goggles, leather gloves, overalls
- The work area is clean and the workbench is stable
- You have all tools: screwdrivers, spanners, combination pliers, multimeter
Step 2: Inspect the Motor and Starter Components
- Check the motor nameplate for rated voltage, current, and speed
- Verify the rotor resistance starter rating matches the motor
- Inspect slip rings for wear and clean them if necessary
- Check carbon brushes for proper length and spring tension
Step 3: Connect the Rotor Resistance Starter
-
Connect the stator (stator winding) to the three-phase supply as per the motor connection diagram
-
Connect the rotor circuit:
- Connect the three leads from the slip rings to the three terminals of the rotor resistance starter
- Ensure each lead is properly secured with correct terminal connections
- Use a multimeter to verify continuity of all connections
-
Connect the automatic control circuit:
- The automatic starter uses a timer or speed-sensing device
- Connect the control circuit to the supply as indicated in the wiring diagram
- This circuit automatically reduces resistance as the motor speeds up
Step 4: Test the Installation
- Before powering on, manually rotate the motor shaft to check for free movement
- Apply power and observe the motor starting
- The motor should start smoothly with reduced current
- After a few seconds, the automatic mechanism should cut out the resistance
- Use a multimeter to verify normal voltage at the motor terminals during running
A 3-phase slip-ring motor has the following nameplate data:
- Rated voltage: 415 V
- Rated current: 50 A
- Starting current (with rotor resistance): 120 A
- Starting current (without rotor resistance): 300 A
Calculate the percentage reduction in starting current when using the rotor resistance starter.
Solution:
Percentage reduction=Without starterWithout starter−With starter×100%
=300300−120×100%
=300180×100%=60%
The rotor resistance starter reduces the starting current by 60%, which greatly reduces the stress on the power supply and other equipment.
- Always disconnect and lock out the power supply before working on the motor
- Wear appropriate PPE at all times
- Ensure all connections are tight to avoid sparking or overheating
- Never operate the motor with the slip ring covers removed
- Keep hands and tools away from rotating parts
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor fails to start | Open rotor circuit | Check slip ring connections and brushes |
| Excessive starting current | Resistance not properly connected | Verify all three resistance phases are connected |
| Uneven motor acceleration | One phase of resistance open | Check continuity of each phase |
| Burning smell | Overloaded motor or poor connections | Stop immediately and investigate |
In Tanzania, slip-ring motors with rotor resistance starters are commonly used in water pumping stations for irrigation and town water supply. For example, at the Kidatu or Mtera hydro power stations, large motors drive water pumps to distribute electricity. When these motors start, the rotor resistance starter ensures they draw manageable current from the local grid, preventing voltage drops that could affect households and businesses in nearby areas like Morogoro or Iringa. The automatic feature means operators don't need manual intervention, making the system reliable for continuous water supply operations.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret the control diagram.
- Identify types and ratings of machine control.
- Mark the location for installing the machine control systems.
- Install the machine control.
- Terminate cables.
- Test the machine control.
- Apply safety precautions.
- Clean the workplace.
Tathmini ya matokeo
The installed automatic starterresistor/capacitor/inductor starter functions as per standards.
Tathmini ya maarifa
Knowledge evidence: Detailed knowledge of:
Method used: The student should explain how to install an automatic starterresistor/capacitor/inductor starter.
Principles: The student should explain the principles related to installing an automatic starterresistor/capacitor/inductor starter.
Theories: The student should explain:
- The types of machine control.
- The major parts of machine control.
- The power rating of machine control.
- The application and importance of machine control.
Detailed knowledge about:
- Safe handling of machine controls.
Swali
Which type of induction motor requires a rotor resistance starter for starting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado