Mada za sehemu hiiInstalling control system of DC machinesMada 3
- Installing diverter in the armature
- Installing varistor in the field winding
- Starting a D.C. machine by using an autotransformer starter
A DC motor must not be switched straight onto its full supply voltage. At the moment of switching on, the armature is at rest and produces no back EMF, so only the very small armature resistance limits the current. The starting current can be ten or more times the full-load current. It burns the commutator and brushes, overheats the winding and jerks the driven machine. One way to start gently is to give the armature a low voltage and raise it as the motor gains speed. An autotransformer, used together with a rectifier, can do this.
An autotransformer is a transformer with one winding on an iron core. The whole winding is connected to the supply, and the output is taken between one end and a tapping part of the way along, so part of the winding is common to input and output.
Vout=NtotalNtap×Vin
It depends on a changing magnetic field, so it works only on alternating current. It must never be connected to a DC supply: there is no transformer action, and the winding draws a very large current and burns out. To start a DC machine, the autotransformer is connected to the AC mains (230 V, 50 Hz) and its reduced AC output goes through a rectifier, which changes it to DC for the armature.
- Tapped autotransformer: fixed tappings, commonly 50%, 65% and 80% of the supply voltage. It is used in starters for large three-phase AC induction motors.
- Variable autotransformer (variac): a carbon brush slides along the winding and gives any voltage from zero to full voltage. This type suits a small DC motor, because the voltage can start from zero.
Read the nameplate: input voltage and frequency, output voltage range, and maximum output current (or kVA). The current ratings of the autotransformer and the rectifier must be higher than the largest starting current allowed, usually about 1.5 times the full-load current of the motor. Most DC motors are started by resistance starters (three-point and four-point), which put resistance in series with the armature. The autotransformer and rectifier method is found on test benches and small drives fed from AC mains.
- Three basic types: series (very high starting torque: cranes, hoists, traction), shunt (nearly constant speed: lathes, fans, pumps) and compound (presses, lifts, rolling mills).
- Speed: N∝ΦEb. A stronger field gives a lower speed; a weaker field gives a higher speed. Speed regulation is the change in speed from no load to full load, as a percentage of full-load speed.
- Commutation: the commutator and brushes reverse the current in each armature coil as it passes a brush, so that the torque always acts one way. Poor commutation shows as sparking.
- Armature reaction: the magnetic field of the armature current distorts and weakens the main field, causing sparking unless interpoles are fitted.
Follow the diagram from the supply to the motor: double-pole isolator and fuses or circuit-breaker, autotransformer, rectifier, ammeter, then the armature terminals (A1 and A2). The shunt field (E1 and E2) is not fed through the autotransformer. It has its own rectifier on the full supply voltage, so that the field is at full strength before the armature receives any voltage. A motor with a weak field takes a heavy current and tries to race.
- Switch off, lock the isolator in the off position, hang a warning tag and prove the circuit dead with a tester that has just been checked on a known supply.
- Choose a dry, well-ventilated position near the motor. Mark the fixing holes using the base as a template and a spirit level, drill, insert rawl plugs and screw the unit down level and firm.
- Run cables of the correct size in conduit or trunking. Strip them without nicking the conductor, fit lugs, terminate as the diagram shows and tighten every terminal.
- Connect the metal cases of the autotransformer and rectifier, and the motor frame, to the earthing conductor.
- Test the continuity of every conductor and of the earth, then the insulation resistance between conductors and earth with a megger (at least 1 MΩ). Disconnect the rectifier for this test, because the test voltage can damage it.
- Check that the motor turns freely, the guards are fitted and the autotransformer control is at zero.
- When the installation has been checked by your supervisor, remove the lock and switch on. The field is now energised.
- Turn the control up slowly. The motor starts to turn at a low voltage. Watch the ammeter and keep the armature current below about 1.5 times the full-load current.
- As the speed rises, the back EMF grows and the current falls. Keep raising the voltage until the armature is at its rated voltage.
- Watch the commutator for heavy sparking.
- To stop, turn the control back to zero and then switch off the supply. Never switch off the field while the armature is still supplied.
- An autotransformer does not isolate its output from the mains. Even when it is set to a low voltage, its output terminals can be at 230 V to earth. Treat every terminal as live.
- Never alter a connection with the supply on: isolate, lock off and prove dead first.
- Never open the field circuit of a running shunt motor, and never run a series motor without load. In both cases the speed can rise dangerously.
- Keep hands, hair and loose clothing away from the shaft. Wear safety goggles, safety boots and overalls, and keep the floor dry.
A 200 V DC shunt motor has an armature resistance of 0.5 Ω and a full-load armature current of 20 A.
(a) Starting current on full voltage: I=0.5200=400A, which is 20 times the full-load current.
(b) Armature voltage that limits the starting current to 1.5×20=30A: V=30×0.5=15V.
(c) As a percentage of full voltage: 20015×100=7.5%.
Only a small voltage is needed to start the motor, which is why the control starts from zero and is raised gradually. At full speed the back EMF is about 190 V, so the current is 0.5200−190=20A, the full-load value.
Collect cable off-cuts and stripped insulation, put scrap copper aside for recycling, sweep up drilling dust, wipe and return the tools, and store the meters in their cases.
A motor repair workshop in Morogoro that has only an AC mains supply needs to test a DC motor after servicing it. The technician feeds the field at full voltage, connects the armature through a variable autotransformer and rectifier, and raises the voltage slowly from zero while watching the ammeter. The motor runs up smoothly, with no current surge to trip the circuit-breaker or burn the commutator.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret control diagrams.
- Identify types and ratings of D.C. machine controls.
- Prepare the base of D.C. machine control.
- Mark the location for installing the machine D.C. control systems.
- Fix and align the D.C. machine control.
- Install and terminate cables of the D.C. machine control.
- Test the D.C. machine control.
- Apply safety precautions.
- Clean the workplace.
Tathmini ya matokeo
D.C. machines control fixed, installed and functions as per manufacturer’s manual specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to start a D.C. machine by using an autotransformer starter.
Principles: The student should explain the principles relating to starting a D.C. machine by using an autotransformer starter.
Theories: The student should explain:
- The three basic types of D.C. machines.
- The commutation process.
- Speed regulation applied to D.C. machines.
- The armature reaction in D.C. machines.
- The Application of different types of D.C. machines.
Circumstantial knowledge:
Detailed knowledge about: Safety precautions on maintaining the speed of D.C. machines.
Swali
Why must an autotransformer never be connected to a DC supply?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado