Mada za sehemu hiiPerforming rewinding of electric motorsMada 3
- Rewinding single-phase motors
- Rewinding three-phase motors
- Rewinding D.C. motors
Rewinding a single-phase motor means removing the old, damaged windings from the stator and replacing them with new wire of the correct size and number of turns, restoring the motor to full working condition. This process is done when the windings have burnt out, shorted, or deteriorated due to overload, moisture, or age. Before rewinding, the motor must be disconnected from the power supply and its condition assessed.
- Switch off, isolate the motor from the supply, lock the isolator off and prove the terminals dead before disconnecting the cable. Never open a motor that is still connected to the supply.
- Discharge the capacitor of a capacitor-start or capacitor-run motor before touching its terminals. With the supply isolated, hold a resistor of about 20 kΩ, 5 W, fitted with insulated leads, across the capacitor terminals for several seconds, then confirm with a voltmeter that the voltage is zero. Do not short the terminals with a screwdriver.
- Wear safety goggles, overalls, safety boots and gloves. Get help or use lifting gear for a heavy motor.
- Work in a well-ventilated place. Hot varnish gives off harmful fumes, and varnish and thinners catch fire easily, so keep them well away from the torch and have a fire extinguisher nearby.
- Select the tools before starting: electrician's tool kit, bearing puller, mallet, coil-stripping chisel, wedge remover and wedge driver, slot cleaning brushes, slotting files, wire cutters, micrometer or wire gauge, coil-making machine, multimeter and insulation tester.
Types of winding. Most single-phase motors have concentric windings, in which the coils of each pole lie one inside another and have different spans. The coils may be wound by hand directly into the slots, wound on a former and then inserted, or made as one long skein that is twisted into the slots. Rewind the motor in the same way as it was originally wound.
1. Recording Motor Data and Dismantling the Motor
Before removing any winding, record all nameplate data and winding details. This information is critical because the replacement winding must match the original specifications. Record the following:
- Motor voltage and frequency (e.g., 230 V, 50 Hz)
- Speed in revolutions per minute (rpm)
- Output power (e.g., 1 HP)
- Number of poles
- Diameter and length of the stator bore
- Number of stator slots
- Number of turns per coil
- Wire gauge (diameter)
- Winding configuration (e.g., concentric, lap)
- Type of winding (run winding or start winding)
Failing to record this data means you cannot produce an accurate replacement winding.
Dismantle the motor carefully. Mark each end shield and the frame with a centre punch so that they go back in the same position. Remove the fan cover and fan, undo the through bolts, tap the end shields off with a mallet and withdraw the rotor without scraping it against the stator. Use a bearing puller if a bearing must come off the shaft. Keep all the parts, including the centrifugal switch and capacitor, in a labelled tray.
Then draw the winding diagram before any wire is cut. Sketch the slots and number them, show which slots each coil of the run winding and the start winding occupies (the coil span), how the coils are joined together, and where the leads go.
2. Removing the Old Winding
After recording all data, remove the old winding from the stator:
- Remove the slot wedges with a wedge remover.
- Cut the coils at one end of the stator using a coil-stripping chisel, then pull the coils out of the slots from the other end.
- Count the turns in one coil of each size, for both the run winding and the start winding, and write the numbers on the winding diagram.
- Scrape the enamel off a piece of the old wire from each winding and measure its diameter with a micrometer or wire gauge.
- Heat the core gently with a propane torch or butane torch to soften the varnish holding the windings in place — this makes removal easier. Use only as much heat as is needed, because overheating damages the thin insulation between the core laminations.
- Clean each slot thoroughly using slot cleaning brushes to remove all old insulation, varnish residue, and debris.
- Use a slotting file to remove any burrs or rough edges inside the slots.
Take care not to damage the stator laminations during removal, as this would reduce the motor's efficiency.
3. Preparing the Core and Slots
Before inserting new windings, prepare the core properly:
- Inspect the stator teeth and yoke for bent, burnt or loose laminations. Blue or burnt patches show that the core has overheated; a badly damaged core runs hot and should be reported before the motor is rewound.
- Re-insulate the slots using new slot insulation (paper or fibre sheet) cut so that it lines the whole slot and projects a few millimetres beyond each end of the core. Use insulation of the same thickness and temperature class as the original.
- Chamfer the slot edges using chamfering tools to prevent the insulation from being cut when inserting coils.
Good slot preparation ensures the new winding is properly insulated and mechanically secure.
4. Winding the Coils
Using the data recorded in Step 1, wind new coils to the correct specifications:
- Select the correct wire gauge as recorded — using a wire that is too thick or thin will change the motor's electrical characteristics.
- Wind the required number of turns per coil on a coil-making machine or by hand using a former.
- Form the coils to the correct shape so they fit neatly into the stator slots.
- Keep the start winding and run (main) winding coils separate and clearly identified.
In a split-phase motor the start winding usually has thinner wire and fewer turns than the run winding; in capacitor motors the auxiliary winding can have as many turns as the run winding, or more. Always copy the data taken from the old winding. The wire is copper covered with a thin layer of enamel insulation, so handle it without kinking or scratching it.
5. Inserting the Coils into the Slots
Insert the wound coils into the stator slots following the original winding layout:
- Place the slot insulation before inserting each coil side.
- Insert the run winding first and the start winding on top of it, displaced by half a pole pitch (90 electrical degrees).
- Feed the wires of each coil side into the slot a few at a time by hand and settle them with a fibre or wooden drift — never strike the coils with heavy hammers as this can damage the insulation.
- Arrange the coil ends neatly at the connection side.
- Fold the slot insulation over the wires and drive in a slot wedge with a wedge driver to lock the coils firmly in place.
Maintain the same coil pitch (span) as the original winding to ensure the correct magnetic pole pattern.
6. Connecting the Windings
Connect the coils according to the winding configuration recorded earlier:
- Join the start winding coils in series to form the start winding circuit.
- Join the run winding coils in series to form the run winding circuit.
- Connect the pole groups so that neighbouring poles have opposite polarity (north, south, north, south), following the winding diagram.
- Identify the start and finish leads of each winding.
- Connect the start winding to the centrifugal switch or capacitor (depending on the motor type) through the correct terminal connections.
- Solder or crimp each joint and insulate it with sleeving.
- Tie (lace) the end windings at both ends with lacing cord so that the coils cannot move, and check that they clear the rotor and the end shields.
7. Testing the Winding
Before final assembly, test the newly wound stator:
- Check each winding circuit for continuity using a multimeter — all circuits should show a complete path.
- Test each winding for insulation resistance between the windings and the stator core using a 500 V insulation tester (megger) — a reading below 1 MΩ indicates a problem.
- Test the insulation between the run winding and the start winding as well, with their ends separated.
- Check for short circuits between turns by comparing the resistance of similar coil groups: a group with a clearly lower resistance has shorted turns.
- Verify the winding connections are correct before applying power.
Any faults found at this stage must be corrected before the motor is assembled and run.
8. Varnishing and Baking
After successful testing, impregnate and bake the winding:
- Dip the stator in insulating varnish or apply it by brushing or trickling.
- Bake the stator in an oven (or use a heat lamp) to cure the varnish, hardening and sealing the windings. Follow the time and temperature given by the varnish maker. Let the stator drain first, and wipe varnish off the bore and the seats of the end shields.
- Varnish and its thinners are flammable and their vapour is harmful: work with good ventilation and no naked flame nearby.
- This process protects the windings from moisture, vibration, and heat, extending the motor's service life.
9. Final Assembly and Testing
Reassemble the motor with all original components:
- Fit the bearings to the shaft by pressing on the inner race with a tubular drift (a bearing puller is used only for removing them).
- Refit the rotor into the stator without scraping the winding, then the end shields in their marked positions, the fan and the fan cover. Check that the shaft turns freely by hand.
- Reconnect all leads to the terminal box.
- Perform a continuity and insulation resistance test again.
- With the motor clamped down, its frame earthed, the terminal cover fitted and the supply taken through a fuse or circuit-breaker, run the motor briefly on no load under supervision. Check for abnormal noise, vibration or overheating, and measure the current with a clamp-on meter; it must be below the full-load current on the nameplate.
- Switch off, isolate and discharge the capacitor again before touching any terminal.
If the motor runs smoothly and draws the expected current, the rewind is successful.
- Collect the old copper wire and sell it to a scrap dealer for recycling; never burn it.
- Put old slot insulation, wedges and rags soaked in varnish or thinners into a closed metal bin, away from heat.
- Close the varnish tins, clean the brushes and trays, wipe the tools and return them to the store.
- Sweep the bench and floor so that no wire clippings are left to cause injury or a short circuit.
A single-phase motor has the following nameplate data:
- Voltage: 230 V, Frequency: 50 Hz
- Speed: 1440 rpm
- Stator: 24 slots, 4 poles
- Run winding: 120 turns per coil, wire gauge 1.0 mm diameter
During rewinding, the technician records all this data before removing the old winding. The stator has 24 slots and 4 poles, giving a pole pitch of 24÷4=6 slots per pole, so a full-pitch coil spans from slot 1 to slot 7. The new run winding coils are wound with 120 turns of 1.0 mm wire each, inserted in the correct slots, connected in series, and the start winding (typically thinner wire) is connected separately to the centrifugal switch. After varnishing and baking, the motor is tested and runs at about 1440 rpm, just below the synchronous speed of 4120×50=1500 rpm — confirming the winding data was correctly recorded and reproduced.
In Tanzania, rewinding single-phase motors is a valuable trade skill because these motors power water pumps, maize milling machines, and fans in homes and small businesses. A technician who can rewind a motor correctly saves a customer the cost of buying a brand-new motor, because a rewind usually costs much less. This skill is commonly practised in small workshops across towns like Arusha, Mwanza, and Dar es Salaam, where motor repair services are in constant demand.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment, and safety gear.
- Record nameplate data.
- Disassemble motor.
- Draw a winding diagram.
- Remove old winding and note down the number of turns.
- Clean gaps/slots.
- Insert the insulating paper in the stator.
- Wind new coil.
- Bind the coil and varnish the motor.
- Assemble the back bearing and fan.
- Perform necessary measurements and tests for verification of termination.
- Test the rewound motors.
- Observe safety precautions.
- Clean tools, equipment, and work area.
Tathmini ya matokeo
Single-phase motors rewound as per technical specifications, NEMA standards, and IEE Regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to rewind single-phase motors.
Principles: The student should explain the principles related to rewinding single-phase motors.
Theories: The student should explain:
- Types of motor rewinding.
- Taking data and calculation.
- Core Testing.
- Winding stripping procedures.
- Core preparation.
- Coil making.
- Winding insulation and coil insertion.
- Internal connections.
- Lacing and bracing of windings.
- Inspection of untreated windings.
- Testing untreated and treated windings.
- Winding treatment.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions when handling motors.
- Properties of materials
Swali
A capacitor-start motor has been isolated from the supply and proved dead. How should the technician discharge the capacitor before touching its terminals?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado