Mada za sehemu hiiPerforming rewinding of electric motorsMada 3
- Rewinding single-phase motors
- Rewinding three-phase motors
- Rewinding D.C. motors
Rewinding a three-phase motor involves removing the damaged stator windings and replacing them with new coils of the correct size, number, and configuration. This process restores the motor to proper working condition when the original windings have burned out, shorted, or deteriorated due to age, overload, or moisture ingress. In Tanzania, rewinding three-phase motors is a common trade skill needed in industries, workshops, and agricultural processing plants where these motors power machines like compressors, pumps, and conveyors.
Three-phase induction motors are widely used because of their simplicity, durability, and efficiency. However, the stator windings (the coils of wire wound around the stator core) can fail due to:
- Overheating caused by overload or blocked ventilation
- Electrical failure such as phase-to-phase short circuits or ground faults
- Mechanical damage from vibration or foreign objects
- Environmental factors like moisture, dust, or chemical exposure
When windings fail, the motor cannot operate. Rewinding restores the motor to its original electrical specifications, saving the cost of purchasing a new motor.
The following tools and equipment are needed for rewinding three-phase motors:
- Electrician's tool kit — screwdrivers, pliers, wire cutters, strippers
- Coil tripping chisel — for cutting and removing old coils
- Slot cleaning brushes — for cleaning stator slots after removing old windings
- Coil making machine or manual winding forms — for forming new coils
- Hammers and mallets — for tapping components into place
- Wedge drivers and removers — for installing slot wedges
- Propane or butane torch — for heating and bending components
- Tubing cutter — for cutting insulating tubing
- Adjustable wrench — for tightening nuts and bolts
- Bearing remover (puller) — for removing bearings from the shaft
- Power hand drill — for drilling and fastening
- Insulation materials — slot liners, phase insulation, varnished cambric
- Winding wire — correct gauge and grade for the motor specifications
Before starting any rewinding work, observe these essential safety practices:
- Disconnect power — Ensure the motor is isolated from the electrical supply and cannot be accidentally energized.
- Allow cooling — Never work on a recently run motor; let it cool to avoid burns.
- Wear protective gear — Use safety glasses, gloves, and appropriate clothing.
- Work in a clean area — Keep the workspace free from oil, dirt, and metal fragments that could contaminate the windings.
- Handle tools safely — Use sharp tools carefully to avoid cuts.
- Fire safety — Have a fire extinguisher nearby when using torches.
Step 1: Motor Inspection and Data Recording
Before disassembling the motor, record the nameplate data:
- Voltage (e.g., 400V or 415V for three-phase)
- Current (e.g., 15A)
- Power (e.g., 7.5 kW)
- Speed (e.g., 1440 rpm)
- Frequency (50 Hz in Tanzania)
- Connection type (star or delta)
- Number of poles (e.g., 4 poles)
- Frame size and manufacturer
Also note the slot count of the stator and the original coil pitch (the distance between the two sides of a coil, measured in slot numbers).
Step 2: Dismantling the Motor
- Remove the motor from its mounting and place it on a suitable workbench.
- Remove the end bells (end covers) by undoing the bolts.
- Carefully withdraw the rotor from the stator housing.
- Remove the bearings if they are worn or damaged.
- Mark the stator frame orientation to ensure correct reassembly.
Step 3: Removing Old Windings
- Cut the winding connections using the coil tripping chisel or wire cutters.
- Heat the winding ends with a torch to soften the varnish and make removal easier.
- Pull out the coils from each slot, being careful not to damage the stator laminations.
- Clean all slots thoroughly using slot cleaning brushes to remove old insulation, varnish, and debris.
- Inspect the stator core for damage such as broken laminations or burrs.
Step 4: Preparing the Stator
- Check the stator slots for sharp edges; use chamfering tools if needed.
- Insert new slot liners (insulation material) into each slot to insulate the windings from the core.
- Ensure the stator is clean and dry before proceeding.
Step 5: Winding the Coils
The new coils must match the original specifications:
- Number of turns per coil — determined by the motor design and voltage
- Wire gauge — must carry the rated current without overheating
- Coil pitch — the distance between the two sides of a coil; usually expressed as a number of slots (e.g., 1–9 pitch)
Example Calculation:
For a 4-pole, 36-slot three-phase motor with a coil pitch of 1–9:
- Number of poles = 4
- Number of slots = 36
- Number of slots per pole per phase = 36 ÷ (4 × 3) = 3 slots
- If using single-layer winding, each coil occupies 2 slots
- Total number of coils = 36 coils (one per slot for single-layer)
The coil pitch of 1–9 means one side of the coil is placed in slot 1 and the other side in slot 9 (span of 8 slots).
- Form the coils using a coil making machine or manual winding form.
- Insert one side of each coil into its starting slot, passing over the appropriate number of slots for the other side.
- Distribute the coils evenly across all phases (U, V, W).
- Use proper layering and phase insulation between coils of different phases.
Step 6: Connecting the Windings
- Connect the coils according to the original diagram or standard three-phase configuration:
- Star connection — join one end of each phase winding to a common point (neutral); the other ends connect to the three supply lines
- Delta connection — join the end of one phase winding to the start of the next, forming a closed triangle
- Secure all connections with crimp connectors or soldering.
- Apply insulating varnish and allow it to dry.
Step 7: Inserting Slot Wedges
Insert wedges into the slots to lock the windings in place and prevent them from moving during operation. Use wedge drivers to tap them in firmly.
Step 8: Reassembly
- Insert the rotor back into the stator.
- Refit the end bells and secure with bolts.
- Install new bearings if they were removed.
- Check that the rotor turns freely without rubbing the stator.
Step 9: Testing
After rewinding, test the motor to verify correctness:
- Continuity test — Check that each phase winding is continuous and not open-circuited using a multimeter.
- Insulation resistance test — Use a megohmmeter to measure insulation resistance between windings and between windings and the frame. The reading should be at least 1 MΩ.
- Winding resistance test — Measure the resistance of each phase; all three phases should have equal or nearly equal resistance.
- High-voltage test — Apply a higher-than-normal voltage (e.g., 2 × rated voltage + 1000V) for one minute to check for winding breakdown.
- No-load test — Run the motor briefly without load to check for unusual noise, vibration, or overheating.
If all tests pass, the motor is ready for reinstallation and use.
- Using wire with wrong gauge (too thin causes overheating; too thick won't fit)
- Incorrect number of turns per coil
- Wrong coil pitch affecting motor performance
- Poor connection causing high resistance and heating
- Insufficient insulation leading to short circuits
- Damaging stator laminations during coil removal
In Tanzania, three-phase motors power important equipment at small businesses like maize mills (mashua), water pumps for irrigation, and welding machines at construction sites. When such a motor fails due to burnt windings, a trained technician can rewinding it at a fraction of the cost of buying a new motor. For example, rewinding a 5 HP (3.7 kW) three-phase motor costs approximately TZS 150,000–250,000, while a new motor of the same rating costs TZS 800,000 or more. This skill helps small business owners in towns like Arusha, Mwanza, and Dodoma keep their machines running without expensive downtime.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment, and safety gear.
- Record nameplate data.
- Disassemble motor.
- Draw a winding diagram.
- Remove old winding and note down the number of turns.
- Clean gaps/slots.
- Insert the insulating paper in the stator.
- Wind new coil
- Bind the coil and varnish the motor.
- Assemble the back bearing and fan.
- Perform necessary measurements and tests for verification of termination.
- Test the rewound motors.
- Observe safety precautions.
- Clean tools, equipment and work area.
Tathmini ya matokeo
Three-phase motors Rewound as per technical specifications, NEMA standards, and IEE Regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to rewind three-phase motors:
Principles: The student should explain the principles related to rewinding three-phase motors.
Theories: The explain:
- Type of motor rewinding.
- Taking data and calculation.
- Core Testing.
- Winding stripping procedures. Preparation.
- Coil making. insulation and coil Insertion.
- Internal connections.
- Lacing and bracing of windings.
- Inspection of untreated windings.
- Testing untreated and treated treatment.
Detailed knowledge about:
- Safety precautions when handling motors.
- Properties of materials
Swali
What information must be recorded from the motor nameplate BEFORE starting to rewind a three-phase motor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado