Mada za sehemu hiiConstructing resistive circuitsMada 4
- Building single resistor circuit
- Building series circuit
- Building parallel circuit
- Building series-parallel resistive circuit
Building Single Resistor Circuit
A single resistor circuit is the simplest type of resistive circuit. It consists of one resistor connected to a power source, allowing current to flow through in one complete path. Understanding how to build this circuit is the foundation for all electrical installation work.
A resistor is an electrical or electronic component that limits or controls the flow of electric current through a circuit. Its main function is to "resist" the flow of electrons, thereby reducing the current or creating a voltage drop.
In a pure resistive circuit, there is no inductance or capacitance—the circuit behaves according to Ohm's Law.
Resistors are classified into two main categories:
Linear Resistors
Linear resistors produce a voltage drop across themselves when current flows through them, following Ohm's Law. They are divided into:
-
Fixed Resistors: Their resistance value cannot be changed. Types include:
- Wire Wound Resistors
- Thin Film Resistors
- Carbon Composition Resistors
-
Variable Resistors: Their resistance value can be adjusted. Types include:
- Potentiometer
- Rheostat
- Trimmer Resistor
Non-Linear Resistors
Non-linear resistors do not obey Ohm's Law. Their resistance changes with temperature or voltage:
- Thermistors: Resistance changes with temperature
- Varistors (MOV): Resistance changes with applied voltage
- Photo Resistors (LDR): Resistance changes with light intensity
There are two methods to determine resistor values:
1. Colour Code Method

Resistors have coloured bands that indicate their resistance value and tolerance. The colour bands are read from left to right, with each colour representing a number:
| Colour | Number |
|---|---|
| Black | 0 |
| Brown | 1 |
| Red | 2 |
| Orange | 3 |
| Yellow | 4 |
| Green | 5 |
| Blue | 6 |
| Violet | 7 |
| Grey | 8 |
| White | 9 |
The first two bands give the significant digits, the third band indicates the multiplier (number of zeros), and the fourth band shows tolerance (gold = ±5%, silver = ±10%).
2. Using a Multimeter
Set the multimeter to resistance mode (Ω) and connect the probes across the resistor to read its value directly.
Ohm's Law describes the relationship between voltage, current, and resistance:
V=I×R
Where:
- V = Voltage across the resistor (in volts, V)
- I = Current flowing through the resistor (in amperes, A)
- R = Resistance of the resistor (in ohms, Ω)
This formula can be rearranged to find any unknown value: I=RVandR=IV
To build a single resistor circuit, you will need:
- One resistor (e.g., 10kΩ)
- A breadboard or circuit board
- Connecting wires (copper wires have low resistance)
- Variable DC power supply (0-30V) or battery
- LED (Light Emitting Diode)
- Multimeter for measurements
- Safety goggles and overalls

-
Prepare the circuit diagram – Draw or study the schematic showing the resistor, power source, and LED in series.
-
Select a resistor – Choose a resistor of desired resistance value (e.g., 10kΩ). Identify its value using the colour code or multimeter.
-
Insert the resistor onto the breadboard – Place the resistor leads into appropriate rows on the breadboard.
-
Connect the wires – Use connecting wires to complete the circuit path from the power source through the resistor and LED back to the source.
-
Connect the power supply – Set the power supply to 6V DC and connect it to the circuit. The LED should light up.
-
Clean the workspace – After completing the activity, disconnect the power and organize your tools.
A student builds a single resistor circuit using a 1kΩ resistor and a 6V power supply. An LED is connected in series with the resistor. The LED has a voltage drop of 2V.
Calculate the current flowing through the circuit.
Solution:
First, find the voltage across the resistor: VR=Vsupply−VLED=6V−2V=4V
Now apply Ohm's Law: I=RVR=1000Ω4V=0.004A=4mA
Therefore, the current flowing through the circuit is 4 milliamperes (mA).
Single resistor circuits are used for:
- Current limiting: Preventing damage to components like LEDs
- Voltage dropping: Reducing voltage for devices requiring lower power
- Signal conditioning: Adjusting signal levels in electronic equipment
When current flows through a resistor, electrical energy is converted into heat energy. This happens because the resistor opposes the flow of current, and this opposition causes the electrons to collide with atoms in the resistor material, releasing energy as heat. This is called Joule heating.
In Tanzania, single resistor circuits are commonly found in simple electronic devices like phone chargers and torch lights. For example, a Tanzanian farmer using a solar-powered LED lighting system in a chicken coop relies on resistors to limit current and protect the LEDs from burning out, ensuring the lights last longer and work safely throughout the night.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Design a circuit diagram of the resistive circuit.
- Identify equipment, tools, and materials required.
- Prepare resistors and cables for termination.
- Build a single resistor circuit.
- Solder the built circuits.
- Apply safety precautions.
- Clean work area, tools and equipment.
- Store tools, equipment, and remained materials.
Tathmini ya matokeo
The single resistive circuit is constructed as per electrical standards.
Tathmini ya maarifa
Knowledge evidence:
Methods used: The student should explain how to build a single-phase resistor circuit.
Principles: The student should explain the principles related to building a single resistor.
Theories: The trainee should explain:
- The Ohms’ Law and its applications.
- Types of electrical materials.
- Electrical symbols used to construct the resistive circuit.
Detailed knowledge about:
- Safe handling of working tools and equipment
- Electrical hazards
Swali
Which of the following is the main function of a resistor in an electrical circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado