Mada za sehemu hiiConstructing resistive circuitsMada 4
- Building single resistor circuit
- Building series circuit
- Building parallel circuit
- Building series-parallel resistive circuit
Building Series-Parallel Resistive Circuit
A series-parallel resistive circuit combines both series and parallel arrangements of resistors. This type of circuit is also called a combination circuit. The goal is to obtain a desired overall resistance by arranging resistors in different ways within the same circuit.
A combination circuit contains resistors that are connected in series in some parts and in parallel in other parts. Real-world electrical systems often involve such mixed arrangements. By combining series and parallel connections, we can achieve specific resistance values that neither pure series nor pure parallel circuits can provide alone.
When you look at a combination circuit, you need to identify which resistors are connected in series and which are connected in parallel.
- Series connection: Resistors are connected end-to-end in a single path. The same current flows through each resistor.
- Parallel connection: Resistors are connected across common points, providing multiple paths for current flow. Each parallel branch receives the full voltage.
Tip: Redraw the circuit in your notebook and label the sections clearly before calculating.
To find the total resistance of a combination circuit, follow these steps:
- Identify series and parallel groups – Look for resistors that are clearly in series or clearly in parallel.
- Simplify series resistors – Add their resistances together using: RT=R1+R2+R3
- Simplify parallel resistors – Use the parallel formula: RT1=R11+R21
- Repeat – Continue simplifying until you have one equivalent resistance.
- Find final total – This is the total resistance of the entire circuit.
Three resistors are connected as follows:
- R1=10Ω
- R2=20Ω
- R3=30Ω
R1 and R2 are in series, and this series combination is in parallel with R3.
Solution
Step 1: Find the total resistance of R1 and R2 in series: Rseries=R1+R2=10Ω+20Ω=30Ω
Step 2: Now calculate Rseries in parallel with R3: RT1=Rseries1+R31 RT1=30Ω1+30Ω1 RT1=302Ω
Step 3: Take the reciprocal to find RT: RT=230=15Ω
Therefore, the total resistance of the combination circuit is 15 ohms.

Required Tools and Materials
- Resistors (five or more as required)
- Breadboard
- Connecting wires (copper wires with low resistance)
- Variable DC power supply (0-30V)
- LED (light-emitting diode)
- Multimeter
- Safety goggles and overalls
Implementation Steps
- Prepare the circuit diagram – Draw the schematic showing how resistors are connected (series and parallel sections).
- Select resistors – Choose resistors with the values needed for your circuit.
- Insert resistors on breadboard – Place each resistor in the correct position on the breadboard.
- Connect wires – Use connecting wires to complete the circuit path from the power supply through all components.
- Connect LED – Add an LED in series with the circuit to observe operation.
- Set power supply – Set to 6V DC and connect to the circuit.
- Test and observe – The LED should light. Each branch will light according to the resistance value in that branch.
- Clean the workplace – Disconnect power and organize tools after finishing.
Practical Question
If you remove one resistor connected in series, what will happen to the current flow in the parallel branches?
| Connection | Formula |
|---|---|
| Series | RT=R1+R2+R3+⋯ |
| Parallel | RT1=R11+R21+R31+⋯ |
In Tanzanian homes, electrical wiring often uses combination circuits. For example, when wiring a room with multiple lighting points, some lights may be connected in series for switching control while the main power distribution to different sockets uses parallel connections. An electrician must understand how series-parallel combinations work to properly install, troubleshoot, and maintain safe electrical systems in buildings. If a house has a combination circuit with a total resistance of 15Ω connected to a 240V supply, the electrician can calculate the total current using Ohm's Law to ensure the wiring can safely handle the load.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Design a circuit diagram of the series-parallel resistive circuit.
- Identify equipment, tools, and materials required.
- Prepare resistors and cables for termination.
- Build a series-parallel resistive circuits.
- Solder the built circuits.
- Apply safety precautions.
- Clean work area, tools and equipment.
- Store tools, equipment, and remaining materials.
Tathmini ya matokeo
The series-parallel resistive circuit is constructed as per electrical standards.
Tathmini ya maarifa
Knowledge evidence:
Methods used: The student should explain building a series-parallel resistor circuit.
Principles: The student should explain the principles related to building a series-parallel resistor.
Theories: The trainee should explain:
- The application of series-parallel circuit.
- Electrical symbols used to construct the resistive circuit.
Detailed knowledge about:
- Safe handling of work tools and equipment
- Electrical hazards
Swali
A series-parallel resistive circuit is defined as a circuit that:
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado