Mada za sehemu hiiConstructing inductive circuitsMada 5
- Building a single inductive circuit
- Building a series inductive circuit
- Building parallel inductive circuit
- Building a combined inductive circuit
- Testing inductive circuits
An inductor is a coiled wire that stores energy in a magnetic field, and a series inductive circuit connects multiple inductors along a single path so the same current flows through each one.
An inductor is a passive electronic component made of a cylindrical core with many turns of conducting wire (a coil). Its ability to store electrical energy in a magnetic field is called inductance, abbreviated as L. The SI unit of inductance is the Henry (H). Smaller units include millihenry (mH), where 1 mH = 10⁻³ H.
An inductive circuit is a circuit that contains one or more inductors. When inductors are connected in series, they are joined end-to-end in a single path, so that current must flow through each one sequentially.
Total Inductance
When inductors are connected in series, the total inductance is simply the sum of all individual inductances. This is because the magnetic fields of each coil add together.
LT=L1+L2+L3
Where:
- LT = total inductance
- L1,L2,L3 = individual inductance values
Example: Three inductors with values L₁ = 8 mH, L₂ = 4 mH, and L₃ = 6 mH are connected in series. Find the total inductance.
Solution: LT=L1+L2+L3 LT=8 mH+4 mH+6 mH LT=18 mH
Voltage in Series Inductive Circuits
The total voltage across a series of inductors equals the sum of the voltage drops across each individual inductor:
V=V1+V2+V3
Current in Series Inductive Circuits
The same current flows through every component in a series circuit. This is a fundamental characteristic of series connections:
I=I1=I2=I3
Inductive Reactance
Inductive reactance (XL) is the opposition an inductor offers to alternating current (AC). It is calculated using the formula:
XL=2πfL
Where:
- f = frequency in Hertz
- L = inductance in Henry
Important: In a DC circuit, the frequency is zero (f=0). Therefore, inductive reactance in a DC circuit is also zero:
XL=2π(0)L=0Ω
This means an ideal inductor behaves as a short circuit (zero resistance) in a DC circuit after the magnetic field is fully established. Only the internal resistance of the coil is considered in DC circuits.

Required Tools and Materials
- Three inductors (coils) with known values
- Breadboard
- Connecting wires (copper wires have very low resistance)
- Variable DC power supply (0-30V)
- Bulb or lamp with holder
- Multimeter (for measuring)
Implementation Steps
-
Prepare the circuit diagram – Draw the schematic showing inductors L₁, L₂, and L₃ connected in series with the power supply and bulb.
-
Select the inductors – Choose three inductors with appropriate inductance values (for example, 10 mH, 20 mH, and 30 mH).
-
Plug the components onto the breadboard – Insert the inductors, lamp holder, and connecting wires into the breadboard to create a complete series path.
-
Connect the wires – Ensure all connections are secure and complete the circuit loop from the power supply positive terminal, through all inductors, through the bulb, back to the negative terminal.
-
Set the power supply and test – Set the DC power supply to 6V and connect it to the circuit. Observe how the bulb behaves. In a series inductive circuit, connecting more inductors in series increases the total inductance but does not change the current path.
-
Clean the workplace – After the activity, disconnect the power supply and organize all tools and materials properly.
When you build and test a series inductive circuit with a DC source:
- At the instant the switch is closed, the current does not jump to its maximum value immediately. The inductor opposes the change in current (Lenz's Law).
- The bulb initially glows dimly and gradually becomes brighter as the magnetic field builds up in the coils.
- After a short time (approximately 5 time constants), the inductor behaves like a short circuit (a wire), and the bulb reaches full brightness.
- When the circuit is disconnected, you may observe a spark at the switch terminals because the collapsing magnetic field induces a high voltage.
| Property | Series Inductive Circuit |
|---|---|
| Total Inductance | LT=L1+L2+L3 |
| Current | Same through all components |
| Voltage | Sum of individual voltages |
| DC Reactance | Zero (XL=0) |
In Tanzania, series inductive circuits are found in common electrical systems such as car ignition circuits, where an inductor (ignition coil) stores energy and releases it as a high-voltage spark to start the engine. Electricians and mechanics in Dar es Salaam and across the country use this principle when diagnosing starter motor problems or maintaining vehicle electrical systems.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- The student should be able to:
- Design a circuit diagram of the inductive circuit.
- Identify equipment, tools and materials required.
- Prepare inductors and cables for termination.
- Build a series inductor circuit.
- Solder the built circuits.
- Measure and record the inductive parameters of the circuits.
- Observe safety precautions.
- Clean work area, tools and equipment.
Tathmini ya matokeo
Series inductive circuit constructed as per given standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to build a series inductive circuit.
Principles: The student should explain the principles related to building a series inductive circuit.
Theories: The student should explain:
- The application of a series inductive circuit.
Detailed knowledge about:
- Safety precautions on inductive load charges.
- Safe handling of working tools, equipment and an inductor.
Swali
What is an inductor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado