Mada za sehemu hiiConstructing inductive circuitsMada 5
- Building a single inductive circuit
- Building a series inductive circuit
- Building parallel inductive circuit
- Building a combined inductive circuit
- Testing inductive circuits
An inductor is a basic component made by winding wire into a coil that stores energy in a magnetic field when current flows through it. In this topic you will learn what an inductor is, recognise different types, and build a simple circuit that contains one.
An inductor is a passive electrical component that resists changes in current. When current flows through a coil of wire, it produces a magnetic field around the coil. This magnetic field stores energy temporarily.
Key points:
- The ability of an inductor to store energy is called inductance
- Inductance is measured in henrys (H)
- A simple inductor is just a coil of insulated copper wire
- The coil may be wound around air, iron, or ferrite material
There are three common types you need to identify:
- Air core inductor — coil wound in air with no magnetic material inside
- Iron core inductor — coil wound around an iron core for stronger magnetic field
- Ferrite core inductor — coil wound around a ferrite core; used in electronic equipment
A circuit with one inductor is found in many everyday devices:
- The choke (ballast) of a fluorescent lamp, which limits the lamp current
- Electric bells, buzzers and relays, where a coil becomes an electromagnet
- Filters in power supplies and radios, where a coil smooths the current
Follow these steps carefully using proper safety gear.
Step 1: Plan the circuit
Draw a simple circuit diagram showing:
- A DC power source (battery, e.g., 9 V)
- A switch
- An inductor (your coil), drawn as a row of small loops and labelled L
- A resistor (e.g., 1 kΩ, which is 1,000 Ω) to limit the current. A coil of wire has almost no resistance, so without the resistor the battery would be short-circuited
- Connecting wires
Step 2: Gather tools and materials
Collect from your workstation:
- Electronics board
- Electrician's knife
- Combination pliers
- Long nose pliers
- Diagonal cutting pliers
- Soldering iron with stand, and solder
- Analogue and digital multimeter
- Measuring tape
- Overalls, safety goggles, and safety boots
Step 3: Prepare the inductor
Use insulated (enamelled) copper wire so that the turns do not short-circuit each other. Wind approximately 20–30 turns closely side by side around a pencil or other cylindrical object, leaving about 5 cm free at each end, then slide the coil off. This is your air core inductor. Scrape the enamel off the last 1 cm of each end with the electrician's knife, cutting away from your body, until the copper is bright. Cut the connecting wires to length with the diagonal cutting pliers and strip about 1 cm of insulation from each end.
Step 4: Assemble the circuit
- Place all components on the electronics board
- Use combination pliers to connect wires firmly to each component
- Follow your circuit diagram exactly
- Ensure all connections are tight and no bare wires touch each other
Step 5: Solder the joints
- Solder only when the battery is disconnected
- Heat the joint with the tip of the iron for a few seconds, then feed solder onto the joint (not onto the iron) until it flows. A good joint looks bright and smooth
- Hold the wire with long nose pliers, not your fingers, because the wire gets hot
- Always return the iron to its stand, never touch the tip, work where there is fresh air so that you do not breathe the fumes, and wash your hands afterwards
Step 6: Measure and record
- With the battery disconnected, set the multimeter to resistance (Ω) and measure the resistance of the coil. It will be very low, usually less than 1 Ω
- Reconnect the battery, set the multimeter to DC voltage and close the switch. Measure the voltage across the battery, across the resistor and across the inductor
- Set the multimeter to DC current (mA), connect it in series with the circuit and measure the current
- If your meter has an inductance (L) range, disconnect the coil and measure its inductance
- Open the switch and observe what happens
- Record every reading in a table with the columns: quantity measured, meter range used, reading and unit
A student builds a series circuit with a 9 V battery, a switch, a coil of 25 turns, and a 1 kΩ resistor. The resistance of the coil measures 0.2 Ω.
- When the switch is open, no current flows and the multimeter reads 0 V across the coil.
- When the switch is closed, the current is I = V ÷ R = 9 V ÷ 1,000 Ω = 0.009 A, which is 9 mA. (The 0.2 Ω of the coil is too small to change this.)
- The voltage across the resistor is almost the full 9 V. The voltage across the coil is only V = I × R = 0.009 A × 0.2 Ω = 0.0018 V, so the meter shows about 0 V. With a steady direct current, an inductor behaves like a plain piece of wire.
- The inductor acts only at the moment the current changes. When the switch is closed, the coil delays the rise of the current for an instant. When the switch is opened, the collapsing magnetic field produces a short pulse of voltage that tries to keep the current flowing.
With a small hand-wound air core coil this pulse is far too small to see or feel. With a large iron core coil of many turns, such as a relay coil or a choke, the pulse can be many times the supply voltage and can cause a spark at the switch contacts. This shows that an inductor stores energy in its magnetic field and releases it when the circuit is broken.
- Always wear overalls, safety goggles, and safety boots in the workshop
- Never touch live wires or components while the circuit is connected to a power source
- Use tools only for their intended purpose
- Keep your workbench clean and organised
- Disconnect the battery before you change any connection, solder a joint or measure resistance
- Never connect the coil to the battery without the resistor in series. The coil would short-circuit the battery, and the wire and battery would get hot
- Switch off a circuit that contains a large inductor before disconnecting it. Never pull a wire off a coil that is carrying current, because the voltage pulse can give a shock or damage the meter
- Handle the coil gently so that the turns are not crushed and the enamel is not scratched
- Disconnect the battery and store it where its terminals cannot touch metal
- Unplug the soldering iron and let it cool on its stand before putting it away
- Wipe the tools, and return the tools, meters and unused components to their places
- Collect wire offcuts and solder scraps, put them in the waste bin and wipe the bench
In Tanzania, inductors are found inside phone chargers and car alternators. For example, when an electrician in Dar es Salaam repairs a vehicle's charging system, they work with inductors inside the alternator that use magnetic fields to convert mechanical energy into electrical energy, charging the battery and powering the lights and radio while the engine runs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Design a circuit diagram of the inductive circuit.
- Identify equipment, tools and material required.
- Prepare inductors and cables for termination.
- Build a single inductor circuit.
- Solder the built circuits.
- Measure and record the inductive parameters of the circuits.
- Observe safety precautions.
- Clean work area, tools and equipment.
Tathmini ya matokeo
Inductive circuit constructed as per given standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to build a single inductive circuit.
Principles: The student should explain the principles related to building a single inductive circuit.
Theories: The student should explain:
- The application of a single inductive circuit.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions on inductive load charges.
- Safe handling of working tools, equipment and an inductor.
Swali
What is the unit of measurement for inductance?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado