Mada za sehemu hiiConstructing inductive circuitsMada 5
Testing Inductive Circuits
Testing inductive circuits involves checking how an inductor behaves when connected to a DC power source. An inductor stores energy in a magnetic field when current flows through it, and this behavior can be observed during charging and discharging phases.
Inductive circuit testing is the process of examining how an inductor behaves in a DC circuit by observing the charging and discharging phases. When an inductor is connected to a DC source, it does not allow current to change instantly. Instead, current builds up gradually while the magnetic field around the coil grows.
To test an inductive circuit, you will need:
- An inductor (for example, 150mH or 470mH)
- A two-way switch
- A 12V lamp (as the resistive load)
- Connecting wires
- A 12V battery
- A breadboard for building the circuit
A typical test circuit for inductive charging and discharging consists of:
- An inductor (L) connected in series
- A lamp (R) as the load
- A two-way switch to change between charging and discharging positions
- A 12V battery as the power source
The switch allows you to connect the inductor to the battery (charging) or to the lamp alone (discharging).
When the switch is moved to position 1 (connected to the battery):
- At the moment of connection (t=0): The voltage across the inductor is maximum (equal to the supply voltage), but the current is zero
- Current behavior: The current gradually increases from zero to its maximum value (I = V/R)
- Voltage behavior: The voltage across the inductor gradually decreases to zero
- Lamp behavior: The lamp starts with a dim light and gradually becomes brighter
This happens because the inductor opposes any change in current (Lenz's Law). The magnetic field takes time to build up.
When the switch is moved to position 2 (disconnected from battery, connected to lamp):
- The energy stored in the magnetic field is released
- Current continues to flow in the same direction but gradually decreases to zero
- Voltage across the inductor also decreases
- Lamp behavior: The lamp starts at full brightness and gradually dims to off
Important observation: If the inductor is disconnected without providing a path for current (no load), a high voltage spark can appear at the switch terminals because the current tries to stop abruptly.
The time constant (τ) of an RL circuit determines how quickly the inductor charges or discharges:
τ=RL
Where:
- τ = time constant in seconds
- L = inductance in Henrys
- R = resistance in Ohms
Key points about time constants:
- After 1 time constant (1τ), the current reaches about 63% of its maximum value
- After 5 time constants (5τ), the inductor is fully charged or discharged
- After 5τ, the inductor behaves like a short circuit (zero resistance) in DC circuits
- Current reaches its maximum value and voltage across the inductor drops to zero
Example: An inductor of 150mH is connected in series with a 12V lamp in a test circuit. If the lamp has a resistance of 10Ω, calculate the time constant.
Solution:
Given:
- L = 150mH = 0.15 H
- R = 10Ω
Using the formula:
τ=RL=100.15=0.015 seconds
This means the circuit reaches approximately 63% of its maximum current in 0.015 seconds (15 milliseconds), and fully stabilizes after 5τ = 5 × 0.015 = 0.075 seconds (75 milliseconds).
Inductive reactance (X_L) is the opposition an inductor offers to alternating current (AC):
XL=2πfL
Where:
- X_L = inductive reactance in Ohms
- f = frequency in Hertz
- L = inductance in Henrys
Important: In a DC circuit, frequency f = 0, so:
XL=2π×0×L=0Ω
This means a DC source experiences no reactance from an inductor, only its internal wire resistance.

From practical testing of inductive circuits, we observe that:
- An inductor does not dissipate energy; it only stores it in the magnetic field
- An inductor changes current gradually rather than abruptly
- An inductor reaches maximum or minimum values in five time constants
- After five time constants, an inductor behaves like a short circuit in DC networks
- The lamp brightness changes gradually during both charging and discharging
When testing inductive circuits:
- Do not leave the circuit connected for too long or the inductor may overheat
- Always discharge the inductor properly before touching
- Wear safety goggles when working with circuits that may produce sparks
In Tanzania, the behavior of inductors during charging and discharging is applied in car ignition systems. When you turn the ignition key, the inductor (ignition coil) stores energy and then releases it quickly to create a high-voltage spark that ignites the fuel. This principle is also used in fluorescent tube starters found in many Tanzanian homes and shops — the inductor helps produce the initial high voltage needed to start the tube lighting.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- The student should be able to:
- Design a circuit diagram of the inductive circuit.
- Identify equipment, tools and materials required.
- Prepare inductors and cables for termination.
- Build a single inductor circuit.
- Solder the built circuits.
- Measure and record the inductive parameters of the circuits.
- Observe safety precautions.
- Clean work area, tools, and equipment.
Tathmini ya matokeo
Inductive circuit constructed tested and readings recorded as per given standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to test inductive circuit.
Principles: The student should explain the principles related to testing the inductive circuit.
Theories: The student should explain:
- How ammeter is connected to measure current in inductive circuit.
Detailed knowledge about:
- Safety precautions when soldering the inductors.
Swali
What is observed in an inductive circuit when the switch is moved to position 1 (charging phase)?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado