Mada za sehemu hiiConstructing capacitive circuitsMada 4
- Building a single capacitor circuit
- Building series capacitor circuit
- Building parallel capacitor circuit
- Building combination capacitor circuit
A series capacitor circuit is formed when two or more capacitors are connected one after another in a single path so that the same charge flows through each capacitor. The main reason for connecting capacitors in series is to decrease the total capacitance of the circuit.

A series capacitor circuit is an electrical circuit in which all the capacitors are connected one after another in the same path, so that the same charge or current flows to each capacitor as shown in the circuit diagram.
- There is only one path for current to flow from one point to another.
- The individual capacitors have the same charge on each capacitor.
- The total capacitance of capacitors connected in series is smaller than the smallest capacitance in the series circuit.
- The potential difference across each capacitor will be inversely proportional to its capacitance.
The total capacitance of a series capacitor circuit is obtained by adding up the reciprocals (1/C) of the capacitance values of the individual capacitors and then taking the reciprocal of the sum. The formula is:
CT1=C11+C21+C31+⋯+Cn1
Where:
- CT is the total capacitance
- C1,C2,C3,...Cn are the individual capacitances
A series capacitor circuit consists of three capacitors with capacitances C₁ = 2F, C₂ = 4F, C₃ = 6F connected to a DC voltage source of 10V. Calculate:
(a) The total capacitance (b) The charge on each individual capacitor (c) The voltage across each individual capacitor
Solution
Step 1: Find total capacitance
CT1=21+41+61
CT1=0.5+0.25+0.1667=0.9167
CT=0.91671=1.0917F
Step 2: Find the charge (same on each capacitor in series)
Using the formula Q=C×V:
Q=CT×V=1.0917×10=10.917C
Therefore:
- Charge on C₁ = 10.917 C
- Charge on C₂ = 10.917 C
- Charge on C₃ = 10.917 C
Step 3: Find voltage across each capacitor
Using V=CQ:
Voltage across C₁: V1=210.917=5.46V
Voltage across C₂: V2=410.917=2.73V
Voltage across C₃: V3=610.917=1.82V
Check: Total voltage = V₁ + V₂ + V₃ = 5.46 + 2.73 + 1.82 = 10V ✓
Required Tools and Materials
- Capacitors with known capacitance values (e.g., 10 nF, 30 nF, 40 nF)
- Connecting wires
- Breadboard
- Multimeter or capacitance meter
- Power supply (AC or DC)
Safety Precautions
- Always discharge capacitors before handling or connecting them by using a resistor to safely drain stored charge.
- Wear safety goggles when working with capacitors.
- Ensure hands are dry when working with electrical components.
Implementation Steps
- Draw the circuit diagram showing the capacitors connected in series with the power supply.
- Select the capacitors with the desired capacitance values.
- Connect the capacitors in series by linking the terminals end-to-end in a single path.
- Connect the series combination across the power supply terminals.
- Measure the total capacitance across the open ends of the series circuit using a multimeter.
- Measure the charge stored in each capacitor using a capacitance meter.
- Disconnect and discharge all capacitors individually after the activity.
- Clean the workplace and return all tools to their proper places.
- In series connection, adding more capacitors decreases the total capacitance.
- The charge on each capacitor in a series circuit is the same.
- The voltage across each capacitor is different and depends on its capacitance value.
- Smaller capacitance capacitors in series develop higher voltage across them.
In Tanzania, series capacitor circuits are commonly found in some types of electrical filter systems used in radio receivers and communication devices found in rural areas. When a technician is repairing a simple electronic device that uses capacitors for timing or filtering, they may need to replace a faulty capacitor in a series configuration and must understand how the total capacitance changes to ensure the device works properly.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Design a circuit diagram of the capacitive circuit.
- Identify equipment, tools, and materials required.
- Prepare capacitors and cables for termination.
- Build a series capacitor circuit.
- Solder the built circuits.
- Measure and record the capacitive parameters of the circuits.
- Apply safety precautions.
- Clean work area, tools, and equipment.
Tathmini ya matokeo
Capacitive current in the build series capacitor circuit conforms to the electrical block diagram.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: Build a series - capacitive circuit.
Principles: The student should explain the principles related to building series capacitive circuit.
Theories: The student should explain:
- Behaviour of a series capacitive circuit.
- Properties of dielectric materials.
Detailed knowledge about:
- Hazards Control Safe handling of work tools, and equipment.
Swali
What is the correct formula for calculating the total capacitance (CT) of three capacitors connected in series?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado