Mada za sehemu hiiConstructing capacitive circuitsMada 4
- Building a single capacitor circuit
- Building series capacitor circuit
- Building parallel capacitor circuit
- Building combination capacitor circuit
A parallel capacitor circuit is built by connecting capacitors side by side across common points, allowing each capacitor to experience the full source voltage while storing different amounts of charge based on its capacitance.

A parallel capacitor circuit is an electronic circuit in which all the capacitors are connected side by side in different paths. When a voltage is applied to the parallel circuit, each capacitor receives the same voltage across its plates, but the capacitor with higher capacitance stores more charge, while the capacitor with lower capacitance stores less charge.
Connecting capacitors in parallel increases the total plate area without increasing the distance between them, which results in a larger overall capacitance.
The following are the key properties of capacitors connected in parallel:
-
Voltage: All capacitors in a parallel circuit have the same voltage across their plates. This voltage is equal to the source voltage. Mathematically: VC1=VC2=VC3
-
Charge: Each capacitor stores its own charge. The charge on each capacitor depends on its capacitance value. A higher capacitance capacitor stores more charge.
-
Total Capacitance: The total capacitance in a parallel circuit is found by simply adding up the capacitance values of all individual capacitors:
CT=C1+C2+C3+⋯+Cn
This formula shows that adding capacitors in parallel increases the total capacitance, unlike series connection where capacitance decreases.
Example
A parallel capacitor circuit consists of three capacitors with values: C1=8F, C2=4F, and C3=2F, connected to a 10V DC battery.
Solution:
(a) Total capacitance:
CT=C1+C2+C3=8F+4F+2F=14F
(b) Charge stored on each capacitor:
Using the formula Q=C×V:
- Charge on C1: Q1=8×10=80C
- Charge on C2: Q2=4×10=40C
- Charge on C3: Q3=2×10=20C
(c) Total charge:
QT=Q1+Q2+Q3=80+40+20=140C
Required Materials and Tools
- Capacitors with known capacitance values
- A power supply or battery with appropriate voltage rating
- Connecting wires
- Breadboard or circuit board
- Multimeter (for measurement)
- Safety goggles, overalls, and safety boots
Implementation Steps
-
Prepare the circuit diagram: Draw the parallel circuit diagram showing all capacitors connected across the voltage source.
-
Select capacitors: Choose capacitors with the required capacitance values. Ensure their voltage rating is higher than the source voltage.
-
Arrange components: Place all capacitors on the breadboard. Each capacitor should have one terminal connected to the positive side of the power source and the other terminal connected to the negative side.
-
Connect the circuit: Use connecting wires to link all capacitor terminals in parallel across the power source. One wire connects all positive terminals together, and another wire connects all negative terminals together.
-
Test the circuit: Switch on the power supply and verify that each capacitor is connected properly. Use a multimeter to measure voltage across each capacitor — all should show the same voltage.
-
Measure capacitance: Use a multimeter or capacitance meter to measure the total capacitance across the circuit. The measured value should equal the sum of individual capacitances.
-
Clean up: Disconnect the power source, discharge capacitors safely, and clean the work area.
Safety Precautions
- Always discharge capacitors before handling them by using a discharge resistor
- Wear safety goggles and overalls when working with electrical components
- Ensure the power supply is turned off before making connections
- Do not exceed the voltage rating of any capacitor
-
Calculate the combined capacitance in microfarads (μF) when two capacitors each with 47nF are connected in parallel.
-
One capacitor of 470nF is connected in parallel with a capacitor of 1μF. Find the total capacitance.
-
If you remove one capacitor from a parallel circuit, what happens to the total capacitance and the voltage across the remaining capacitors?
In Tanzania, parallel capacitor circuits are commonly found in power factor correction systems used in industries and commercial buildings. For example, at a market in Dar es Salaam, electrical shops use capacitor banks connected in parallel to improve power factor and reduce electricity bills. When multiple capacitors are connected in parallel, they store more charge to help balance the reactive power in the electrical system, making equipment run more efficiently and reducing energy costs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Design a circuit diagram of the capacitive circuit.
- Identify equipment, tools, and materials required.
- Prepare capacitors and cables for termination.
- Build a parallel capacitor circuit.
- Solder the built circuits.
- Measure and record the capacitive parameters of the circuits.
- Apply safety precautions.
- Clean work area, tools, and equipment.
Tathmini ya matokeo
Capacitive current in the built parallel capacitor circuit conforms to the electrical block diagram.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Build a parallelcapacitive circuit.
Principles: The student should explain the principles related to building parallel capacitive circuit.
Theories: The student should explain:
- Behaviour of parallel capacitive circuit.
- Properties of dielectric materials.
Detailed knowledge about:
- Hazards Control Safe handling of work tools, and equipment.
Swali
What is a parallel capacitor circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado