Mada za sehemu hiiMeasuring electrical quantitiesMada 3
- Measuring voltage in the circuit
- Measuring current in the circuit
- Measuring resistance in the circuit
Measuring Voltage in the Circuit
Voltage is the force or pressure that pushes electrons through an electric circuit. To work safely with electrical equipment, you must know how to measure voltage correctly using the right instruments and proper procedures.
Voltage is the electrical pressure that forces electrons to flow through a conductor from one point to another. In Tanzania, we see voltage in action every day when we switch on a light bulb or charge a phone.
- Formula symbol: E or V
- Unit: Volt (V)
- Instrument used: Voltmeter or multimeter
Voltage is measured across a component or power supply. This means the two probes of the voltmeter are connected to both sides of the component being measured, in parallel with the circuit.
Voltmeter
A voltmeter is an instrument designed specifically to measure voltage. It is always connected across (in parallel with) the component or supply whose voltage you want to find.
Multimeter
A multimeter (also called a VOM or multitasker) is a versatile instrument that can measure voltage, current, and resistance. It comes in two types:
- Analog multimeter – uses a moving pointer over a scale
- Digital multimeter – displays the reading as a number on a screen
For measuring DC voltage, set the function switch to V–, V––, DCV, or VDC.
Always follow these safety rules when measuring voltage:
- Ensure the circuit is live – Voltage must be measured while the circuit is switched ON or connected to a power supply.
- Use the correct range – Start on the highest range to avoid damaging the meter. If your meter is auto-ranging, it will detect the correct range automatically.
- Connect probes correctly – The black probe always goes into the COM jack. The red probe goes into the V (voltage) jack when measuring voltage.
- Never touch metal probes while they are connected to a live circuit. Always hold the insulated handles.
- Do not let probes touch each other – This can cause severe sparking and damage the meter.
- Wear protective equipment – Use plastic gloves and safety boots as required.
Important warning: Never set the meter to resistance (Ω) when measuring voltage. This can damage the meter and cause injury.

Follow these steps carefully:
- Select the function – Turn the function switch to DCV (for DC voltage) or ACV (for AC voltage).
- Choose the range – Select a range higher than the maximum voltage you expect. If you are unsure, start with the highest range.
- Insert test leads – Plug the black lead into COM and the red lead into the V jack.
- Connect the probes – Touch the black probe to the negative side and the red probe to the positive side of the component or supply. The probes are connected in parallel.
- Read the display – Observe the reading on the screen. Note the unit of measurement (V or mV).
- Record and switch off – Write down your reading, then disconnect the probes and switch off the power supply.
A student builds a simple circuit with a 47Ω resistor and a 9V/6W bulb connected to a 12V DC power supply.
Question: What voltage will be measured across the bulb?
Solution:
- Set the multimeter to DCV (DC voltage).
- Choose a range above 12V (such as 20V).
- Connect the black probe to the negative terminal of the power supply.
- Connect the red probe to the point after the resistor but before the bulb (to measure voltage across the bulb).
- Switch on the power supply.
- The multimeter displays the voltage across the bulb. If the circuit is working correctly, the reading should be approximately 9V (the rated voltage of the bulb).
The student records the reading and compares it with the expected value. Any difference may indicate a problem with the circuit or the components.
- Voltage is the force that pushes electrons through a circuit
- Voltage is measured in Volts (V)
- The instrument for measuring voltage is a voltmeter or multimeter
- Voltage is measured across a component (in parallel)
- Always start on the highest range when measuring unknown voltage
- Never measure voltage with the meter set to resistance
- Safety first: wear protective gear and never touch live probes
In Tanzania, electricians use voltage measurement every day when installing or repairing electrical systems in homes, schools, and shops. For example, when wiring a new shop in Dar es Salaam, an electrician checks that the mains voltage (usually 230V in Tanzania) is present at the distribution board before connecting switches and sockets. This ensures appliances like fridges, lights, and phone chargers receive the correct voltage and work safely without being damaged.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Determine component values.
- Connect simple electric circuits.
- Perform soldering.
- Measure electric voltage.
- Apply safety precautions.
- Clean workplace.
Tathmini ya matokeo
A record of values of electrical voltage conforming to the specified ratings and Ohm’s law.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to measure voltage in the circuit.
Principles: The student should explain the principles related to measuring voltage in the circuit.
Theories: The student should explain:
- The Ohm’s law.
- Different component ratings.
Detailed knowledge about:
- Caution when performing measurement.
- Safe handling of measuring instruments.
Swali
What is the SI unit used to measure voltage?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado