Mada za sehemu hiiMeasuring electrical quantitiesMada 3
- Measuring voltage in the circuit
- Measuring current in the circuit
- Measuring resistance in the circuit
Measuring Resistance in the Circuit

Resistance is the hindrance or friction that a component offers to the flow of electric charges (electrons) through a circuit. When electrons try to pass through a resistor, they experience opposition that causes some electrical energy to be converted into heat.
The unit of resistance is the Ohm, with the symbol Ω (omega). The formula symbol for resistance is R. For example, a resistor with a value of 100 ohms is written as 100 Ω.
The instrument used to measure resistance is called an ohmmeter. In modern digital multimeters, resistance measurement is one of the functions available.
How an Ohmmeter Works
An ohmmeter contains a small internal battery that provides a tiny current. When you connect the meter to a resistor, the amount of current that flows depends on the resistance value. The meter measures this current and displays it as a resistance value.
- When the test leads are clipped together (touching each other), the meter should display 0 Ω because there is zero resistance between the leads.
- When the leads are left open (not connected to anything), the meter displays infinite resistance (shown as ∞ or OL on digital meters).
- When a resistor is connected between the leads, the reading increases based on how much current that resistance allows to flow.
Important Rule
Resistance must always be measured with the circuit switched OFF or with the component disconnected. If you measure resistance while power is on, you can damage the meter and get incorrect readings.
To measure resistance, you will need:
- Digital Multimeter (DMM) or analog ohmmeter
- Resistors (for practice, such as 150 Ω, 4.7 kΩ, and 220 kΩ)
- Breadboard
- Connecting wires
- Circuit diagram showing the test circuit
Step 1: Prepare the Test Circuit
Identify the resistor(s) you want to measure. For example, you may have three resistors: R1 = 150 Ω, R2 = 4.7 kΩ, and R3 = 220 kΩ placed on a breadboard.
Step 2: Set the Multimeter to Resistance Mode
Turn the function switch on your multimeter to the resistance setting. Look for symbols like Ω, kΩ (kilohms), or MΩ (megohms). Choose the range that matches or exceeds the expected resistance value. If you are unsure, start with the highest range.
Step 3: Insert the Test Leads
- Plug the black lead into the jack labelled COM (common).
- Plug the red lead into the jack labelled Ω (ohms).
Step 4: Zero the Meter (If Required)
Before measuring, touch the metal probes of both leads together. The meter should read 0 Ω. If it does not, your meter may need adjustment or the battery may be low.
Step 5: Connect the Probes to the Component
Hold the plastic handles of the probes and place the metal tips across (in parallel with) the resistor whose resistance you want to measure. Do not touch the metal tips with your fingers, as your body resistance will add to the measurement.
Step 6: Read the Display
Read the value shown on the display. Note the unit (Ω, kΩ, or MΩ).
Step 7: Switch Off the Function
When finished, return the dial to a non-ohms setting to conserve the internal battery.
- Always ensure the circuit power is OFF before measuring resistance.
- Never leave the multimeter on the ohms setting when not in use.
- Do not touch metal probe tips while measuring — your body resistance will cause inaccurate readings.
- Use the correct range to avoid damaging the meter.
A student wants to measure the resistance of a resistor labelled with colour bands brown (1), black (1), and brown (×10). The expected value is:
R=10×10=100Ω
Procedure:
- Turn the multimeter dial to the 200 Ω range (or Ω setting with auto-ranging).
- Insert leads: black to COM, red to Ω.
- Touch probes together — display shows 0 Ω.
- Place probes across the resistor terminals.
- Display reads 100 Ω (or very close, such as 98 Ω to 102 Ω, which is normal).
The resistor is functioning correctly.
- What will happen if you measure resistance with the power switched on?
- State two safety precautions to observe when measuring resistance.
In Tanzania, electricians use resistance measurement to test the condition of wiring in buildings before connecting power. For example, when wiring a new house in Dar es Salaam, a technician checks whether the insulation of copper wires has developed faults by measuring resistance — low resistance indicates good insulation, while very high or infinite resistance may mean a broken wire that needs replacement.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- The student should be able to:
- Determine component values.
- Connect simple electric circuits.
- Perform soldering.
- Measure electric resistance.
- Apply safety precautions.
- Clean workplace.
- Store tools and equipment.
Tathmini ya matokeo
A record of values of electrical resistance conforming to the specified ratings and Ohm’s law.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to measure resistance in the circuit.
Principles: The student should explain the principles related to measuring resistance in the circuit:
Theories: The student should explain:
- Ohm’s law.
- Different component ratings.
Detailed knowledge about:
- Caution when performing measurement.
- Safe handling of measuring instruments.
Swali
Which instrument is used to measure resistance in a circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado