Mada za sehemu hiiMeasuring electrical quantitiesMada 3
- Measuring voltage in the circuit
- Measuring current in the circuit
- Measuring resistance in the circuit
Measuring Current in Electrical Circuits
Electric current is the flow of electric charges (electrons) through a circuit. To work safely with electrical systems, you must know how to measure this current accurately using the correct instrument and proper connection method.

Current is the flow of electric charges (electrons) through a circuit. It is the rate at which electrons move past a point in a conductor.
- Symbol for current: I
- Unit of current: Ampere (A)
- Smaller units: milliampere (mA) = 0.001 A, microampere (μA) = 0.000001 A
Electric current flows from the positive terminal to the negative terminal of a power source. This is called conventional current direction.
The instrument used to measure electric current is called an ammeter.
Ammeters are often part of a multimeter (also called a VOM or multitasker), which can measure voltage, current, and resistance. Digital multimeters display the reading as a number, while analog multimeters use a moving pointer.
Important rule: The ammeter must be connected in series with the circuit or component whose current you want to measure.
This means:
- Open the circuit at the point where you want to measure current
- Connect the ammeter in that opening so that all current flows through it
- The ammeter becomes part of the circuit path
If you connect the ammeter in parallel (across a component) instead of in series, the low internal resistance of the ammeter will allow a very large current to flow. This will damage the meter severely and may damage the circuit as well.
Follow these precautions to avoid injury and equipment damage:
- Always use protective equipment as required (insulated gloves, safety boots)
- Know what measurement you are taking — current is measured in series
- Start on the highest range when measuring current to avoid damaging the meter
- Never connect the ammeter across a voltage source or in parallel with a component
- Do not touch the metal probes while the circuit is live
- Check that your meter's range is above the expected current before connecting
Equipment needed: Multimeter, test circuit (resistor, bulb, connecting wires, power supply, toggle switch)
- Prepare the test circuit — Connect the components (resistor, lamp, power supply) on a breadboard
- Set your device to measure current — Turn the function switch to A–, mA, or DCA
- Choose the correct range — Select a range above the maximum expected current. If unsure, start with the highest range
- Insert the test leads — Plug the black lead into COM, and the red lead into the A (or mA) jack
- Break the circuit — Open the circuit at the point where you want to measure current
- Connect the meter in series — Connect the probes so current flows through the meter
- Switch on the power — Turn on the circuit and read the display
- Record the reading — Note the value and unit shown on the display
- Switch off and disconnect — Turn off power before removing the meter
- Clean up — Store equipment and clean the workplace
A student builds a simple circuit with a 9V battery, a 47Ω resistor, and a 9V/6W lamp. Using a digital multimeter set to measure current in series with the circuit, the display shows 0.15 A.
Calculate the current flowing through the circuit and confirm it matches the reading.
Using Ohm's Law: I = V/R = 9V/47Ω = 0.191 A
The actual reading of 0.15 A is slightly lower because the lamp has its own resistance, reducing the total current slightly. This demonstrates that measuring current directly with an ammeter is more accurate than calculating it.
- Connecting the ammeter in parallel instead of series — this can damage the meter
- Selecting a range that is too low — this can overload and damage the meter
- Measuring current with the power off — the circuit must be live
- Forgetting to switch the multimeter to current mode when measuring current
In Tanzania, electricians and technicians use ammeters when installing and maintaining electrical systems in homes, schools, and businesses. For example, when wiring a new shop in Dar es Salaam, an electrician would use a multimeter set to measure current in series with the lighting circuit to ensure the wiring can safely handle the load without overheating, preventing fire hazards and ensuring the electrical installation meets safety standards.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- The student should be able to:
- Determine component values.
- Connect simple electric circuits.
- Measure electric current.
- Apply safety precautions.
- Clean workplace.
- Store tools and equipment.
Tathmini ya matokeo
A record of electrical current values conforming to the specified ratings and Ohm’s law.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to measure current in the circuit.
Principles: The student should explain the principles related to measuring current in the circuit.
Theories: The student should explain:
- Ohm’s law.
- Different component ratings.
Detailed knowledge about:
- Caution when performing measurement.
- Safe handling of measuring instruments.
Swali
What is electric current?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado