Mada za sehemu hiiMaintaining starter motorsMada 4
- Rectifying pre-engaged starter motor
- Rectifying inertial starter motor
- Rectifying axial starter motor
- Rectifying co-axial starter motor
A pre-engaged starter motor is a type of starter motor commonly used in modern vehicles, especially those with high-compression engines and automatic transmissions. It uses a solenoid switch to ensure that the pinion gear engages with the flywheel before the motor begins to turn, providing a smoother and more reliable starting process than traditional inertia starters. This starter motor is also called an overrunning clutch starter.
The pre-engaged starter motor consists of several key components that work together to start the engine:
Armature: An electromagnet mounted on a shaft of a laminated soft iron core wrapped with windings of copper wire connected to the commutator.
Commutator: A section of the armature where the brushes make contact, delivering power to the windings. It consists of two plates attached to the armature shaft.
Brushes: Made of carbon, these run on a section of the commutator at the rear of the housing to conduct electricity.
Solenoid: Contains a wire coil wrapped around a moveable core called a plunger. It switches to close the electrical connection and connect the starter motor to the vehicle's battery.
Plunger: Uses the vehicle battery and solenoid to push itself forward and engage the starter drive.
Actuating Arm: Connected to the plunger; when the plunger moves forward, it pushes out the starter drive at the opposite end.
Starter Drive: Also called pinion stop, it combines a one-way clutched gear and springs. Once engaged, the gear extends to the flywheel and is clutched to spin in one direction to avoid damage from over-cranking.
Field Coil: Coils connected in series that create an electromagnet which turns the armature, delivering torque.
Pole Shoes: Steel or iron plates positioned in the centre of the field coil that become magnetized when power is applied.
The operation follows a specific sequence:
- When the ignition is turned on, the solenoid is actuated and moves a lever that first shifts the pinion gear along the shaft.
- This movement allows the pinion to engage with the flywheel's ring gear before the starter motor rotates.
- This sequence prevents potential damage when a rapidly rotating pinion collides with a stationary flywheel.
- As soon as the pinion is fully engaged, the solenoid closes its contacts, allowing current to flow from the battery to the starter motor.
- The starter motor then cranks the engine.
- As the engine reaches operational speed, a freewheel clutch disengages the starter motor from the flywheel to prevent over-speed damage.
- A return spring withdraws the pinion back to its resting position.
Rectifying a pre-engaged starter motor involves several systematic steps:
Step 1: Bench Testing and Inspection
The starter motor should first be bench-tested to identify operational faults. This includes:
- Checking free running
- Checking current draw
- Listening for any unusual noises
- Inspecting pinion condition and its travel to ensure proper engagement with the flywheel
Step 2: Disassembling the Starter Motor
When the motor is identified as faulty, it should be disassembled carefully. Note any signs of wear or damage on mechanical components such as:
- The case
- Shafts
- Gears
- Brushes
Step 3: Electrical Testing
Test electrical components for faults, including solenoids and windings. Check for:
- Open circuits
- Short circuits
- Ground faults
This determines which parts need repair or replacement.
Step 4: Repairing Fault Components
The fault components that are identified should be repaired. This may involve:
- Machining or soldering to restore functionality
- Replacing components beyond repair with serviceable parts that meet manufacturer specifications
Step 5: Reassembly and Final Testing
Carefully reassemble the starter motor according to the manufacturer's specifications, ensuring no parts are damaged. Follow the prescribed sequence for assembly to maintain proper function.
Step 6: Final Bench Test
Conduct a final bench test to verify that the starter motor operates correctly:
- Check for free running and current draw
- Ensure the pinion is set correctly
- Make adjustments to meet manufacturer's specifications
Materials needed: Sandpaper, wire brush, cotton rags
Tools and equipment: Assorted spanners, screwdrivers, pliers, vice, jumper cable, starter motor, battery, safety gears
Procedure:
- Select tools, equipment and safety gear.
- Observe safety precautions.
- Hold the motor securely in a vice. Be careful of the spinning pinion gear.
- Attach the black/blue wire of the battery jumper cable to the negative terminal of the battery. Attach the other end of this wire to the case of the starter motor.
- Attach the red wire of the battery jumper cable to the positive terminal of the battery. Attach the other end of this wire to the binding stud (terminal 1) of the starter motor.
- Attach one end of the jumper wire to binding stud 2 of the starter motor. While the starter motor is held securely on the vice, touch the other end of the jumper wire to binding stud 1 of the starter motor and observe what happens.
Interpretation of Results:
- If the starter motor rotates at average speed: The starter motor is working correctly. The pinion gear comes out and spins fast and freely.
- If the pinion gear extends but rotates very slowly: There is a problem with the starter motor.
- If the starter motor makes only clicks without rotating: There is a problem with the starter motor.
A student performs a bench test on a pre-engaged starter motor and observes the following:
- The motor makes a clicking sound
- The pinion gear does not rotate
Analysis: According to the bench test criteria, when the starter motor makes only clicks without rotating, there is a problem with the starter motor. The likely causes include:
- Weak battery connection
- Faulty solenoid
- Worn brushes
- Open circuit in the motor windings
Solution: The student should:
- Check the battery connections are clean and tight
- Test the solenoid for proper operation
- Inspect brushes for wear
- Test armature windings for open circuits
- Repair or replace faulty components as needed
In Tanzania, a mechanic working at a garage in Dar es Salaam or Mwanza would regularly use these skills when customers bring vehicles that won't start. For example, when a taxi driver with a Toyota Wish (common in Tanzania) brings their car because the engine won't crank, the mechanic applies the bench test procedure to quickly diagnose whether the pre-engaged starter motor is faulty, checks the solenoid and windings, and either repairs or replaces the starter motor to get the vehicle back on the road — helping the taxi driver resume earning a livelihood.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gear
- Remove the starter from the vehicle engine
- Dismantle pre-engaged starter motor
- Diagnose components for defects
- Rectify faulty components
- Assemble the pre-engaged starter motor
- Test the pre-engaged starter motor on the bench
- Fix the pre-engaged starter motor to the engine
- Test starter for cranking engine
- Observe safety
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
Rectified pre-engaged starter motor conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to rectify pre-engaged starter motors
Principles: The student should explain the principles involved in rectifying pre-engaged starter motor
Theories: The student should explain:
- Construction of pre-engaged starter motor
- Functions of pre-engaged starter motor components
- Starter motor operation
- Magnetism properties
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions
- Manufacturer’s service manual book
Swali
What is the main characteristic of a pre-engaged starter motor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado