Mada za sehemu hiiPerforming gas weldingMada 4
- Using gas welding tools and equipment
- Performing gas welding on metals
- Performing gas metal cutting
- Performing brazing
Gas Metal Cutting: An Introduction
Gas metal cutting is a process that uses a high-temperature flame produced by burning a mixture of oxygen and a fuel gas (usually acetylene) to heat metal until it melts, then uses a jet of pure oxygen to blow away the molten metal, creating a clean cut. This technique is widely used in metalworking, welding, and fabrication to cut through various metals including steel, aluminum, and copper.
- Oxy-acetylene flame: A high-temperature flame created by burning acetylene gas with oxygen, reaching temperatures up to 3,500°C
- Cutting torch: A handheld tool that combines and controls the flow of oxygen and fuel gas to produce the cutting flame
- Kerf: The narrow slot or gap created in the metal during the cutting process
- Regulator: A device that controls and regulates the flow and pressure of gases from the cylinders to the torch
Before performing gas metal cutting, gather the following tools and equipment:
- Oxy-acetylene gas cylinders (oxygen and acetylene)
- Gas regulators
- Gas hoses
- Cutting torch with appropriate tips
- Flashback arrestors
- Striker or lighter
- Hammer and chisel
- Pair of tongs
- Wire brush
- Clamps
- Steel rule or measuring tape
- Marker or scriber for marking cut lines
- Personal protective equipment (PPE)
Safety is paramount when performing gas metal cutting. Always observe the following precautions:
- Wear appropriate personal protective equipment including welding helmet or goggles, gloves, leather apron, and safety boots
- Ensure good ventilation in the work area to remove fumes and gases
- Check all gas connections for leaks before starting
- Keep fire extinguishers nearby
- Secure gas cylinders properly using cylinder trolleys
- Never oil or grease oxygen equipment
- Keep the work area clean and free from flammable materials
Step 1: Preparation
- Clean the metal surface to be cut, removing any dirt, rust, paint, or contaminants
- Place the metal piece on a stable work surface or welding bench
- Mark the cutting line clearly using a marker or scriber and steel rule
- Secure the metal piece with clamps to prevent movement during cutting
Step 2: Setting Up the Equipment
- Connect the oxygen and acetylene cylinders to their respective regulators
- Attach flashback arrestors to the hoses for safety
- Connect the gas hoses to the cutting torch
- Use a cylinder trolley to move heavy cylinders safely
Step 3: Igniting the Flame
- Open the acetylene valve on the torch slightly
- Use a striker to ignite the acetylene gas
- Adjust the acetylene valve until the flame produces a feathered, carburizing flame
- Gradually open the oxygen valve to obtain a neutral welding flame (inner cone clearly defined)
- For cutting, increase the oxygen flow to create a sharp, pointed inner cone
Step 4: Heating and Cutting
- Direct the preheating flames onto the point where the cut will start
- Continue heating until the metal reaches ignition temperature (appears cherry red)
- Open the oxygen lever fully to release the cutting jet
- The oxygen jet reacts with the hot metal, oxidizing it and blowing away the molten metal
- Move the torch steadily along the marked cutting line
- Maintain a consistent travel speed for a smooth, even cut
Step 5: Completing the Cut
- Continue moving the torch along the entire cutting line
- Ensure the molten metal is being blown away on the underside of the cut
- Close the oxygen valve when the cut is complete
- Allow the metal to cool naturally
- Use tongs to handle hot metal pieces
Step 6: Cleaning and Finishing
- Remove any slag or rough edges using a chipping hammer and wire brush
- Inspect the cut surface for smoothness and accuracy
- Clean the work area and store all tools properly
- Close the gas valves on the cylinders and release pressure from the regulators
Scenario: A farmer in Mwanza needs to cut a worn-out steel plate measuring 600 mm × 300 mm into two equal pieces to repair a farm implement.
Solution:
-
Preparation: Clean the plate surface and mark the center line at 300 mm from one edge using a steel rule and marker.
-
Setup: Connect oxygen and acetylene cylinders to regulators, attach flashback arrestors, and connect hoses to the cutting torch.
-
Ignition: Open acetylene valve, strike to ignite, then adjust oxygen to get a neutral flame.
-
Cutting:
- Heat the edge of the plate at the marked line until cherry red
- Open oxygen cutting jet
- Move torch steadily along the line at a consistent speed
- The oxygen blows away molten metal, creating a clean cut
-
Finishing: Allow pieces to cool, remove any slag with chipping hammer and wire brush.
Result: Two pieces of 600 mm × 150 mm each, suitable for the repair work.
| Defect | Possible Cause |
|---|---|
| Rough cut surface | Inconsistent travel speed |
| Excessive slag | Too slow travel speed or wrong flame settings |
| Incomplete cut | Insufficient preheating or oxygen pressure too low |
| Gouging | Oxygen pressure too high |
In Tanzanian agro-mechanics workshops, gas metal cutting is commonly used by farmers and mechanics to cut worn-out metal parts during equipment repair. For example, when repairing a plough or a maize sheller at a village workshop in Arusha, a mechanic would use gas metal cutting to separate damaged steel components and prepare new metal pieces for welding, enabling quick and affordable repairs that keep farming equipment functional throughout the planting season.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret technical drawings.
- Select tools, equipment and materials.
- Take measurements.
- Adjust the cutting flame
- Perform gas metal cutting.
- Observe safety precautions
- Clean tools, equipment, work piece and work place.
- Store tools and equipment.
Tathmini ya matokeo
Gas metal cutting. Conforms to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Perform gas metal cutting
Principles: Students should explain the principles of gas metal cutting.
Theories: Students should explain:
- procedures Perform gas metal cutting
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing gas metal cutting.
- Safe handling of work tools, equipment and work pieces.
- Waste disposal.
Swali
Which tool is used to secure gas cylinders during gas metal cutting to prevent them from falling?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado