Mada za sehemu hiiPerforming gas weldingMada 4
Performing Brazing
Brazing is a metal-joining process that uses a filler metal with a melting point higher than 450°C to create a strong and permanent bond between two or more metal pieces. Unlike welding, brazing does not melt the base metals — it only melts the filler metal, which flows into the joint by capillary action and bonds the pieces together when it cools.
- Welding melts the base metals themselves and fuses them together directly.
- Brazing melts only the filler metal, which bonds the base metals without melting them. This makes brazing suitable for joining dissimilar metals and for jobs where the base metal must not be distorted by high heat.
1. Preparation
Clean the metal surfaces to be joined thoroughly to remove any contaminants, oxides, or impurities. Use a wire brush, sandpaper, or chisel to clean the surfaces. Properly fit and secure the metal pieces, maintaining the desired gap and alignment. A small gap (usually 0.025 mm to 0.075 mm) allows the molten filler metal to flow properly by capillary action.
2. Flux Application
Apply a flux to the metal surfaces. Flux is a chemical compound that prevents oxidation during heating and helps the brazing filler metal flow smoothly into the joint. The type of flux depends on the base metals and filler metal being used.
3. Heating
Use a heat source such as an oxy-acetylene torch to heat the metal pieces and the filler metal. The heat should be directed at the joint area, not directly at the filler metal initially. Gradually heat the workpieces until they reach the proper brazing temperature — typically lower than the melting point of the base metals but high enough to melt the filler metal.
4. Adding the Filler Metal
Once the metal pieces are hot enough, introduce the brazing filler metal (brazing rod or wire) to the joint. The filler metal melts and flows into the gap by capillary action, drawn in by the clean, heated surfaces.
5. Capillary Action
The molten filler metal is drawn into the joint between the two pieces of metal. This action ensures that the filler metal spreads evenly and fills the gap completely, creating a strong bond along the entire joint.
6. Cooling
Allow the joint to cool naturally. Do not quench it suddenly, as rapid cooling may cause cracks or weaken the joint. Once cooled, the joint forms a permanent and reliable connection between the metal pieces.
7. Cleaning
After the joint has cooled, clean any remaining flux residue using a wire brush or appropriate cleaning solution. Inspect the joint for uniformity and strength.
- Oxy-acetylene gas cylinders and accessories
- Brazing rods or filler wire
- Flux
- Welding torch with appropriate tips
- Wire brush
- Chisel
- Tongs
- Clamp
- Hammer
- Safety gear: helmet, safety boots, overall, gloves, leather apron, gas welding goggles
- Wear all personal protective equipment including welding goggles, gloves, leather apron, and safety boots.
- Ensure the work area is free from flammable materials.
- Check all gas connections for leaks before igniting the torch.
- Always use flashback arrestors on gas hoses.
- Keep a fire extinguisher nearby.
In Tanzania, brazing is commonly used in workshop repair of agro-equipment such as repairing cracked pump housings, fixing broken tines on cultivators, or joining broken metal parts on irrigation equipment. For example, a farmer in Mwanza whose water pump casing has a small crack can have it brazed by a local welder using a copper-phosphorus or silver brazing rod to restore the pump without replacing the entire unit — saving both time and money.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Students should be able to:
- Interpret technical drawings.
- Select tools, equipment and materials.
- Take measurements.
- Carry out brazing
- Observe safety precautions
- Clean tools, equipment, work piece and work place.
- Store tools and equipment.
Tathmini ya matokeo
Brazing performed conforms to technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: Students should explain how to:
- Perform brazing.
Principles: Students should explain the principles of Performing brazing
Theories: Students should explain:
- Brazing materials
- Procedures for Performing brazing
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing brazing.
- Safe handling of work tools, equipment and work pieces.
- Waste disposal.
Swali
What is the minimum melting point temperature required for a filler metal to be used in brazing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado