Mada za sehemu hiiServicing television receiversMada 6
- Servicing power supply system of a television
- Servicing deflection system
- Servicing vertical and horizontal circuits
- Servicing high tension circuits
- Servicing television sound system
- Servicing television video system
Power Supply System of a Television
The power supply system converts the mains AC voltage (220V/240V in Tanzania) into the various DC voltages needed by different circuits inside a television receiver. Without a properly functioning power supply, the TV will not turn on or will exhibit symptoms such as no picture, no sound, or intermittent operation.
A typical television power supply consists of several key components arranged in stages:
1. Mains Filter and Fuse
- Mains filter suppresses electrical noise and interference from entering the TV
- Fuse protects the television from excessive current that could cause fire or damage
2. Rectifier Circuit
- Converts alternating current (AC) to pulsating direct current (DC)
- Usually uses a bridge rectifier made of four diodes
3. Filter Capacitor
- Smooths the pulsating DC from the rectifier into a steadier DC voltage
- Stores charge to supply current during peak demands
4. Voltage Regulator
- Maintains a constant output voltage despite variations in input voltage or load
- May be a linear regulator (like the 7805 for 5V) or a switching regulator
5. Power Transformer (in older models)
- Steps down the mains voltage to a lower AC voltage suitable for the TV circuits
- Modern flat-panel TVs often use switched-mode power supplies (SMPS) that eliminate the need for a heavy transformer
When servicing television power supplies, technicians commonly encounter these problems:
- Blown fuse — caused by short circuits, power surges, or failed components
- Failed rectifier diodes — result in no DC output or excessive ripple
- Dry solder joints — create intermittent power or no-power symptoms
- Faulty filter capacitor — causes the TV to shut down randomly or produce distorted picture
- Failed voltage regulator — leads to wrong output voltages, causing the TV not to turn on properly
- Damaged power switch — prevents the TV from powering on at all
Before servicing any television power supply, always follow these safety rules:
- Disconnect the power — Unplug the TV from the mains socket before opening the casing
- Wait for capacitor discharge — High-voltage capacitors can retain charge even after power is removed; discharge them safely using an insulated screwdriver or resistor
- Wear protective gear — Use gloves, safety glasses, and an insulating mat
- Work in a dry area — Never work on a wet bench or with wet hands
- Use proper tools — Ensure your tools are insulated and in good condition
Follow these systematic steps when servicing a TV power supply:
Step 1: Visual Inspection
- Check for burnt components, swollen or leaking capacitors, and damaged wiring
- Look for blown fuses and discoloured circuit board areas
Step 2: Mains Voltage Check
- Use a multimeter to verify that mains voltage reaches the power supply board
- Set multimeter to AC voltage (250V range) and test across the live and neutral points
Step 3: DC Output Voltage Check
- With the TV powered on (carefully), measure DC voltages at various test points
- Common outputs: +5V for microprocessors, +12V for audio amplifiers, +B (typically 100-140V) for the scan circuits
Step 4: Ripple Test (if available)
- Use an oscilloscope to check for excessive ripple on DC outputs
- A healthy power supply should show a smooth DC waveform with minimal noise
Step 5: Component Testing
- Test diodes, capacitors, and resistors individually while the circuit is powered off
- Replace any faulty components identified
A customer brings a television that will not turn on. You observe that the power indicator light does not illuminate.
Diagnosis:
- You open the TV and perform visual inspection — the mains fuse is blackened and broken
- You test the fuse with a continuity checker — it shows no continuity (blown)
- You suspect a short circuit somewhere in the power supply; you inspect the bridge rectifier diodes
- Using the diode test function on your multimeter, you find one diode is shorted (reads 0Ω instead of approximately 0.7V)
Action:
- Replace the blown fuse
- Replace the shorted diode
- Test the TV by plugging it in and turning it on
- Verify correct DC output voltages with your multimeter
This example shows how systematic troubleshooting identifies the root cause — a failed diode that caused excessive current, blowing the fuse.
In Tanzania, television sets are widely used in homes, guesthouses, and small entertainment venues. When a TV fails to turn on, many owners assume it is completely broken and may purchase a new set unnecessarily. A technician with knowledge of power supply servicing can diagnose whether the fault is a simple failed fuse or capacitor — items that cost only a few thousand Tanzanian shillings to replace — and save the customer from spending TZS 150,000 or more on a new television. This skill also supports small electronics repair businesses in local markets, where proper diagnosis and affordable repairs build customer trust and steady income.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret circuit diagrams
- Select tools, equipment and components
- Troubleshoot Television receiver
- Rectify Television faults
- Test Television receiver
- Observe safety precautions
- Clean tools, equipment and workplace
Tathmini ya matokeo
Serviced Television receiver functions as per the manufacturer’s specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to service Television receivers
Principles: The student should explain the principles of:
- Performing soldering
- Servicing Television receivers
- Testing Television receivers
Theories: The student should explain:
- Parts of Television receiver
- Functions of Television parts
- Symbols used in Television circuits
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while servicing Television receivers
- Safe handling of tools and equipment
Swali
What is the main function of the rectifier circuit in a television power supply?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado