Mada za sehemu hiiServicing television receiversMada 6
Vertical and horizontal circuits are essential parts of a television receiver that control the scanning of the electron beam across the screen. Together, they create the raster (the pattern of lines that forms the picture) by moving the beam vertically (top to bottom) and horizontally (left to right). Without these circuits working properly, the television cannot display a proper image — you might see a single horizontal line, a rolled picture, or no picture at all.
The vertical circuit, also called the vertical deflection circuit, controls the vertical movement of the electron beam. It drives the vertical deflection coils in the picture tube to move the beam from the top of the screen to the bottom and back again. This happens about 50 times per second (in PAL system used in Tanzania), creating the vertical scan.
Key components in the vertical circuit include:
- Vertical oscillator generates the 50Hz scanning signal
- Vertical driver amplifies the signal
- Vertical output transistor amplifies the signal further
- Vertical deflection coils are the load that creates the magnetic field for beam deflection
- Feedback network ensures stable vertical scanning
The horizontal circuit, also called the horizontal deflection circuit, controls the horizontal movement of the electron beam. It drives the horizontal deflection coils to move the beam from left to right and then quickly back to the left. This happens about 15,625 times per second (in PAL system).
Key components in the horizontal circuit include:
- Horizontal oscillator generates the 15.625kHz scanning signal
- Horizontal driver amplifies the signal
- Horizontal output transistor switches the high current in the deflection coils
- Horizontal deflection coils create the magnetic field for horizontal scanning
- Flyback transformer (line output transformer) generates high voltage for the picture tube
- S-correction capacitors and linearity coils ensure even spacing of scan lines
Vertical Circuit Faults
| Symptom | Possible Cause |
|---|---|
| No vertical scan (single horizontal line) | Faulty vertical output transistor, broken vertical oscillator, open vertical deflection coils |
| Picture rolled up or down | Faulty vertical sync circuit, poor feedback, weak vertical hold control |
| Poor vertical linearity (people look stretched or squashed) | Faulty vertical linearity coil, defective feedback circuit, aging electrolytic capacitors |
| Picture height too small | Low supply voltage to vertical circuit, weak vertical output, leaky coupling capacitor |
Horizontal Circuit Faults
| Symptom | Possible Cause |
|---|---|
| No horizontal scan (single vertical line) | Faulty horizontal output transistor, open horizontal deflection coils, broken oscillator |
| No picture but sound present | Faulty flyback transformer, failed high voltage circuit |
| Picture narrow horizontally | Weak horizontal output, faulty S-capacitor, low supply voltage |
| Poor horizontal linearity | Faulty linearity coil, defective S-correction capacitor |
| Raster too wide or too narrow | Problems with the flyback transformer or associated capacitors |
Before opening a television receiver, always follow these safety rules:
- Disconnect power — Always unplug the TV from the mains before working inside
- Discharge the CRT — The picture tube (CRT) can hold dangerous high voltage even after unplugging; use a proper discharge tool or insulated screwdriver with grounding lead
- Wear protective gear — Use gloves, overall, and safety boots as provided
- Work on insulated surface — Use a dry, insulated work bench
- Be careful with high voltage — The horizontal circuit generates voltages over 20,000 volts
- Never work alone — Have someone nearby in case of accident
Step 1: Visual Inspection
- Remove the back cover of the television
- Check for obvious damage — burnt components, broken wires, cracked circuit boards
- Look for blown capacitors (bulged or leaked), charred resistors, damaged coils
- Check all connectors and plug-in modules are secure
- Use magnifying glass to inspect soldered joints for cold solder or cracks
Step 2: Power Supply Check
- Connect the television to a variac (variable voltage supply) or use a power supply unit
- Start with low voltage and gradually increase while monitoring
- Check that all supply voltages to vertical and horizontal circuits are within specification
- Use digital multimeter to measure DC voltages at key test points
Step 3: Vertical Circuit Testing
- Check the vertical output transistor — measure voltages at collector, base, and emitter
- Test the vertical oscillator circuit — verify the frequency is approximately 50Hz
- Check all capacitors in the vertical circuit, especially electrolytic capacitors which can dry out
- Measure the resistance of vertical deflection coils with multimeter (should be a few ohms)
- Check the vertical hold control — adjust to see if the picture locks
Step 4: Horizontal Circuit Testing
- Check the horizontal output transistor — measure voltages and test for shorts
- Verify the horizontal oscillator is running at approximately 15.625kHz
- Test the flyback transformer for correct output voltages
- Check all capacitors in the horizontal circuit, particularly the S-correction capacitor
- Measure resistance of horizontal deflection coils
Step 5: Waveform Analysis with Oscilloscope
The oscilloscope is the most important tool for diagnosing vertical and horizontal faults:
- Connect oscilloscope probe to the vertical output test point
- Check vertical waveform — should be a sawtooth wave at 50Hz with proper amplitude
- Connect probe to horizontal output test point
- Check horizontal waveform — should be a sawtooth wave at 15.625kHz
- Compare observed waveforms with the expected waveforms from service manual
- Distorted waveforms indicate faulty components in that circuit
Step 6: Component Replacement
- Identify the faulty component using above tests
- Desolder the faulty component carefully using desoldering pump or wick
- Install the replacement component — ensure correct polarity for capacitors and transistors
- Solder cleanly with appropriate temperature iron
- Check for any solder bridges or cold joints
Step 7: Realignment and Testing
- After repair, reconnect power carefully
- Adjust vertical hold and height controls if needed
- Adjust horizontal hold if necessary
- Check for proper linearity in both directions
- Allow the TV to run for several minutes to ensure stability
- Check all waveforms again with oscilloscope
A television displays only a single bright horizontal line across the center of the screen. There is sound but no picture.
Diagnosis:
-
Observation: The symptom indicates a vertical scanning failure — the beam is not moving vertically at all, only horizontally.
-
Initial check: Use multimeter to measure supply voltage to vertical circuit — voltage is present.
-
Vertical output transistor test: Measure voltages at the vertical output transistor:
- Collector voltage is present but lower than normal
- Transistor appears to be faulty when tested with transistor tester
-
Oscilloscope check: Connect probe to vertical output — no sawtooth waveform is visible, confirming the vertical output stage is not working.
-
Defect identified: The vertical output transistor is defective and must be replaced.
Repair:
- Disconnect power and discharge CRT
- Desolder the faulty vertical output transistor
- Install a new replacement transistor of the same type
- Reconnect power and test
- Use oscilloscope to verify proper 50Hz sawtooth waveform at vertical output
- Adjust vertical hold and height controls to restore full-screen picture
In Tanzania, television receivers are widely used in homes, guesthouses, and community viewing centers. When a television develops scanning problems — such as a rolled picture, narrow image, or single line — understanding vertical and horizontal circuits allows a technician to diagnose and repair the fault locally instead of sending the TV to Dar es Salaam for expensive service. This skill can create a small repair business in a rural town, where a technician can charge around TSh 15,000–30,000 for a typical vertical or horizontal circuit repair, providing income while serving the community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret circuit diagrams
- Select tools, equipment and components
- Troubleshoot Television receiver
- Rectify Television faults
- Test Television receiver
- Observe safety precautions
- Clean tools, equipment and workplace
Tathmini ya matokeo
Serviced Television receiver functions as per the manufacturer’s specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to service Television receivers
Principles: The student should explain the principles of:
- Performing soldering
- Servicing Television receivers
- Testing Television receivers
Theories: The student should explain:
- Parts of Television receiver
- Functions of Television parts
- Symbols used in Television circuits
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while servicing Television receivers
- Safe handling of tools and equipment
Swali
What is the frequency of the vertical scanning signal in the PAL system used in Tanzania?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado