Mada za sehemu hiiServicing television receiversMada 6
Servicing Deflection System in Television Receivers
The deflection system is a critical part of a television receiver that controls the path of the electron beam, allowing it to scan across the screen in a pattern that creates the visible image. Without a properly functioning deflection system, the electron beam would hit the center of the screen continuously, producing only a small bright spot instead of a full picture. Servicing this system involves identifying faults, checking components, and performing adjustments or replacements to restore normal operation.
The deflection system consists of electromagnetic coils mounted on the deflection yoke (also called the yoke assembly) that surround the neck of the picture tube. When electric current flows through these coils, magnetic fields are created that push or pull the electron beam, causing it to move across the screen in a controlled pattern.
Horizontal Deflection
- Moves the electron beam from left to right across the screen
- Operates at a high frequency of approximately 15,625 Hz (for PAL system)
- Controls the horizontal width and linearity of the image
- Uses the horizontal output transistor and line scan transformer
Vertical Deflection
- Moves the electron beam from top to bottom across the screen
- Operates at a lower frequency of approximately 50 Hz
- Controls the vertical height and linearity of the image
- Uses the vertical output transistor and feedback circuits
- Deflection Yoke – Contains both horizontal and vertical coils wound on a ferrite core
- Scan Circuits – Electronic circuits that generate the sawtooth waveforms for scanning
- Horizontal Output Transistor (HOT) – Switches current through the horizontal deflection coil
- Vertical Output IC/Transistor – Amplifies the vertical scan signal
- Line Scan Transformer (LST) – Provides high voltage and deflection power
- Feedback Circuit – Ensures accurate scanning by sending sample signals back to the scan circuits
The electron beam originates from the electron gun at the back of the picture tube. As it passes through the deflection yoke, the magnetic fields created by the coils bend (deflect) the beam:
- The horizontal scan circuit sends a rapidly repeating current through the horizontal coils, causing the beam to sweep left-to-right and return quickly
- The vertical scan circuit sends a slower current through the vertical coils, causing the beam to sweep top-to-bottom
- Together, these two movements create a raster – a pattern of horizontal lines that fill the entire screen
- The synchronization pulses embedded in the broadcast signal ensure that the scanning matches the transmitted image
| Fault Symptom | Possible Cause |
|---|---|
| No horizontal scan (vertical line) | Faulty horizontal output transistor or yoke coil |
| No vertical scan (horizontal line) | Faulty vertical output circuit or open vertical coil |
| Image too narrow | Weak horizontal deflection, low supply voltage |
| Image too wide | Defective linearity capacitor or yoke |
| Image off-center | Shifted yoke position or unbalanced coils |
| Distorted image (bowed sides) | Faulty S-capacitor or horizontal linearity coil |
| Image rolls vertically | Faulty vertical sync or hold control |
| No raster (blank screen) | Deflection yoke failure or power supply problem |
Step 1: Safety Precautions
- Disconnect the TV from the mains power before opening
- Allow capacitors to discharge safely
- Wear safety gloves and overalls
- Work on an insulated work bench with proper lighting
Step 2: Visual Inspection
- Check all wiring connections to the deflection yoke
- Look for burnt components, cracked solder joints, or damaged wires
- Inspect the deflection yoke for physical damage or loose mounting
- Check for signs of overheating on the horizontal output transistor
Step 3: Testing Components
Using a Multimeter:
- Test the resistance of deflection coils (should read close to specified values)
- Check for open circuits in the yoke windings
- Measure voltage supply to the scan circuits
- Test transistors and diodes in the deflection circuit
Using an Oscilloscope:
- Observe the sawtooth waveform at the vertical output
- Check the horizontal drive signal at the base of the HOT
- Verify synchronization between video signal and scan circuits
- Look for distorted waveforms indicating faulty components
Step 4: Adjustment and Replacement
- Realign the deflection yoke if the image is off-center
- Replace faulty components such as the HOT, yoke, or scan ICs
- Adjust horizontal hold and vertical hold controls if available
- Replace swollen or leaking capacitors in the scan circuits
Step 5: Final Testing
- Power on the TV and observe the raster pattern
- Check that the image fills the entire screen evenly
- Verify stable synchronization without rolling or distortion
- Allow the TV to run for several minutes to check for overheating
A television displays only a narrow vertical bright line in the center of the screen. Using the troubleshooting approach:
-
Observation: The symptom indicates that vertical deflection is working (beam moves up and down) but horizontal deflection is not working (beam does not move left to right).
-
Possible causes:
- Open horizontal deflection coil
- Faulty horizontal output transistor
- Damaged line scan transformer
- Broken wiring to the yoke
-
Testing:
- Use a multimeter to check resistance of the horizontal yoke coil (should be a few ohms, not open circuit)
- Check for voltage at the horizontal output transistor collector
- Inspect the HOT for signs of damage
-
Repair: Replace the faulty component (HOT or yoke) and re-test.
This example shows how understanding the function of each deflection type helps locate the fault quickly.
- The deflection system uses electromagnetic coils to steer the electron beam across the screen
- Horizontal deflection operates at high frequency (15,625 Hz); vertical deflection operates at 50 Hz
- Main components include the deflection yoke, scan circuits, output transistors, and the line scan transformer
- Servicing involves visual inspection, testing with multimeter and oscilloscope, and replacing faulty parts
- Always follow safety precautions when working inside a television receiver
In Tanzania, television repair technicians use the skills from this topic to service common TV problems in homes, guesthouses, and small electronics shops across towns like Arusha, Mwanza, and Dodoma. When a customer's TV shows a thin vertical line or a rolling image, a trained technician applies deflection system knowledge to diagnose whether the fault is in the horizontal or vertical scan circuit, replaces the defective component (often a cheap transistor or capacitor), and restores the TV to working condition—saving the customer the cost of buying a new television, which can cost over TSh 500,000.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret circuit diagrams
- Select tools, equipment and components
- Troubleshoot Television receiver
- Rectify Television faults
- Test Television receiver
- Observe safety precautions
- Clean tools, equipment and workplace
Tathmini ya matokeo
Serviced Television receiver functions as per the manufacturer’s specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to service Television receivers
Principles: The student should explain the principles of:
- Performing soldering
- Servicing Television receivers
- Testing Television receivers
Theories: The student should explain:
- Parts of Television receiver
- Functions of Television parts
- Symbols used in Television circuits
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while servicing Television receivers
- Safe handling of tools and equipment.
Swali
What is the primary function of the deflection system in a television receiver?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado