Mada za sehemu hiiDeveloping solar heaterMada 3
- Making flat plate collector solar water heater
- Making evacuated tube collector solar water heater
- Making heat pump system solar water heater
Flat Plate Collector Solar Water Heater
A flat plate collector is a simple device that captures solar energy and converts it into heat for water heating. It consists of a dark absorber plate that absorbs sunlight, pipes through which water circulates, insulation to reduce heat loss, and a glass cover (glazing) that lets sunlight in while trapping heat. In Tanzania, flat plate collectors are widely used in homes, schools, and hospitals to provide hot water using free solar energy, reducing the need for electricity or firewood.
Before assembling a flat plate collector, you must consider several factors:
- Water demand — The amount of hot water needed daily determines the size of the collector and the storage tank. A larger household or institution requires a bigger collector area.
- Panel size — The collector area is measured in square metres. A typical household collector may be 1–2 m².
- Location — The collector must be installed where it receives maximum sunlight throughout the day, free from shading by trees or buildings.
- Orientation — In Tanzania (southern hemisphere), the collector should face true north to capture the most sunlight. The optimal tilt angle is approximately equal to the latitude of the location (about 5–10° for most of Tanzania).
A flat plate collector is made up of the following parts:
- Frame — A rectangular housing usually made of aluminium or galvanized steel, providing structural support.
- Absorber plate — A dark-coloured metal sheet (often painted black or coated with selective absorbing coating) that absorbs solar radiation.
- Risers and manifolds — Copper or PP-R pipes attached to the absorber plate through which water circulates. Risers run horizontally across the plate; manifolds are vertical pipes that distribute and collect water.
- Insulation — Thermal insulation (such as mineral wool or polyurethane foam) placed behind and around the absorber to prevent heat loss.
- Glazing — A transparent glass or plastic cover that protects the absorber and creates a greenhouse effect to trap heat.
- Tank — An insulated storage tank (usually 100–200 litres for a household) to store the heated water.
The following steps describe how to assemble a flat plate collector:
Step 1: Prepare the Frame
Measure and cut the frame materials (aluminium or steel sheets) to the desired dimensions, for example 1 m × 2 m. Use a hacksaw or metal sheet scissors. Drill holes at the corners for screws. Assemble the frame using a screwdriver and right-angle clamps to ensure it is square.
Step 2: Install Insulation
Cut insulation material to fit inside the frame. Place the insulation at the back of the collector and along the sides. This reduces heat loss to the environment.
Step 3: Prepare the Absorber Plate
Cut a dark-coloured metal sheet (galvanized iron or copper) to fit inside the frame. Clean the surface and apply a black matte paint or selective coating to maximize solar absorption.
Step 4: Install the Piping
Cut copper or PP-R pipes to the required lengths using a pipe cutter. Bend the pipes using a pipe-bending tool to form risers. Position the risers horizontally across the absorber plate, spacing them about 10–15 cm apart. Connect the risers to vertical manifolds at both ends using proper fittings. Secure the pipes to the absorber plate using clips or by soldering (if using copper).
Step 5: Attach the Absorber and Pipes
Place the absorber plate inside the frame on top of the insulation. Ensure good thermal contact between the absorber and the pipes. You can use thermal paste or metal straps to improve heat transfer.
Step 6: Install the Glazing
Cut a sheet of glass or transparent plastic to cover the top of the frame. Place a rubber gasket around the edge to create a seal. Secure the glazing with clips or screws, ensuring it is airtight to reduce heat loss.
Step 7: Connect to the Storage Tank
Connect the outlet pipe from the collector to the lower inlet of the insulated storage tank. Connect the return pipe from the tank's upper outlet to the inlet of the collector. Use silicon gun sealant at all pipe joints to prevent leaks. For PP-R pipes, use the PP-R pipe welding machine to create permanent joints.
Step 8: Test the System
Fill the system with water and check for leaks at all joints. Observe water circulation on a sunny day. The water in the tank should begin to heat within a few hours.
The following tools are required for assembling a flat plate collector:
- Drill and drill bits — for making holes in the frame
- Forster drill bit — for drilling holes in pipes
- Screwdriver set — for assembling the frame
- Right-angle clamps — for holding pieces in place
- Handsaw or metal sheet scissors — for cutting materials
- Copper tubing cutter — for cutting copper pipes
- Paint brushes — for applying paint or coating
- Burner and soldering equipment — for joining copper pipes
- Silicon gun — for sealing joints
- PP-R pipe welding machine — for joining PP-R pipes
- Pipe-bending tool — for shaping copper pipes
- PP-R pipe scissors — for cutting PP-R pipes
- Hammers — for shaping metal parts
- Measuring tape — for taking measurements
- Set of wrenches — for tightening nuts and fittings
- Personal Protective Equipment (PPE) — gloves, safety goggles, and apron
- Always wear PPE when cutting, drilling, or soldering.
- Handle sharp tools carefully to avoid cuts.
- Ensure good ventilation when using soldering equipment or silicon sealant.
- Secure the collector frame properly to prevent it from falling.
- Check all gas connections before using the burner.
A family in Dar es Salaam uses 150 litres of hot water per day. The average solar insolation in Dar es Salaam is about 5 kWh/m²/day. Assuming the collector efficiency is 60%, calculate the minimum collector area required.
Solution:
The energy needed to heat 150 litres of water from 20°C to 60°C (ΔT = 40°C) is:
Q=m×c×ΔT
Where:
- m = mass of water = 150 kg (1 litre of water ≈ 1 kg)
- c = specific heat capacity of water = 4.18 kJ/kg·°C
- ΔT = temperature rise = 40°C
Q=150×4.18×40=25,080 kJ/day
Convert to kWh:
Q=3,60025,080=6.97 kWh/day
Accounting for 60% efficiency:
Required solar energy=0.606.97=11.62 kWh/day
Collector area needed:
A=511.62=2.32 m2
Therefore, the family needs a collector area of approximately 2.3 m².
In many Tanzanian towns like Arusha, Mwanza, and Dodoma, flat plate solar water heaters are installed on rooftops of guesthouses, lodges, and residential homes to provide hot water for bathing and cleaning. For example, a small guesthouse in Arusha with 10 rooms can install a 3 m² flat plate collector with a 300-litre storage tank. This system uses free solar energy to heat water, saving about TSh 150,000 per month that would otherwise be spent on electricity or firewood for water heating.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Make black-body surface
- Assemble copper tubing under blackbody surface
- Cover black-body surface with transparent
- Perform plumbing works Test the Flat plate collector solar water heater
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Flat plate collector solar water heater is made as per requirement
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The students should explain how to:
- Interpret drawings
- Fabricate Flat plate collector solar water heater
- Perform piping (inlet/outlet)
- Install storage tank and its accessories.
Principles: The explain principles of:
- Thermodynamics
- Fluid dynamics
Theories: The students should explain: Flat plate collector solar water heater
Swali
Which of the following is NOT a component of a flat plate collector solar water heater?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado