Mada za sehemu hiiDeveloping solar heaterMada 3
- Making flat plate collector solar water heater
- Making evacuated tube collector solar water heater
- Making heat pump system solar water heater
Making Evacuated Tube Collector Solar Water Heater
An evacuated tube collector solar water heater is a device that uses sunlight to heat water for domestic use. It consists of glass tubes from which air has been removed (evacuated) to create a vacuum that acts as excellent insulation, minimizing heat loss. The heater works by absorbing solar radiation through the glass tubes and transferring the heat to water stored in a tank.
Before assembling an evacuated tube collector, you must consider several factors that determine the heater's effectiveness:
1. Water Demand
- Calculate the daily water requirement for the household (typically 50-100 litres per person per day)
- Larger families require bigger collectors and storage tanks
2. Panel Size
- The collector area must match the hot water demand
- A typical single evacuated tube is about 1.8 metres long and 58 mm in diameter
- More tubes = more hot water capacity
3. Location and Orientation
- The collector should face true north in the Southern Hemisphere (including Tanzania)
- Tilt angle should equal the location's latitude (for Tanzania, approximately 6°-12° south)
- Avoid shading from buildings or trees
The main parts include:
- Evacuated glass tubes – double-glazed tubes with a vacuum between them
- Absorber plate – a dark-coated surface inside the tube that absorbs solar radiation
- Copper heat pipe – transfers heat from the tube to the storage tank
- Manifold/header – collects heated water from all tubes
- Storage tank – insulated tank that holds the heated water
- Frame – supporting structure made of galvanized metal
- Glazing – transparent cover that protects the tubes and reduces heat loss
- Insulation – material (like glass wool) that wraps the tank and pipes
Step 1: Constructing the Frame
- Measure and cut the galvanized metal angle sections using a handsaw according to the design dimensions
- Drill pilot holes at connection points using the drill and Forster drill bit
- Join the frame pieces using bolts and nuts, ensuring right angles with angle clamps
- Check that the frame is level and square
Step 2: Installing the Absorber Plates
- Clean the absorber plates to remove any dirt or oil
- Apply a thin, even layer of heat-absorbing black paint if needed
- Position the absorber plates inside each glass tube, ensuring full contact with the heat pipe
- Secure plates in place using the appropriate clips or holders
Step 3: Installing Pipes and Manifold
- Cut copper tubing to the required lengths using a copper tubing cutter
- Bend copper pipes to the necessary angles using a pipe bending tool
- Solder pipe joints using the burner and soldering equipment – apply flux first, then heat and add solder
- Connect the manifold to all tube openings, ensuring leak-free joints
- Use Teflon tape on threaded connections to prevent leaks
- Apply silicon gun sealant at all pipe entry points
Step 4: Installing the Storage Tank
- Position the insulated storage tank on the frame or roof structure
- Connect the tank inlet and outlet pipes to the manifold
- Insulate all exposed pipes using pipe insulation material
- Seal connections with silicon to prevent water ingress
Step 5: Installing Glazing
- Cut the glazing material (tempered glass or polycarbonate) to size using metal sheet scissors
- Place the glazing over the collector frame
- Secure with glazing clips and apply silicone sealant around edges
- Ensure the glazing is weather-tight
Step 6: Testing and Commissioning
- Use a multimeter to check electrical connections (if any backup heating is installed)
- Fill the system with water and check for leaks at all joints
- Tighten any loose connections
- Monitor the system during a sunny day to verify heating
- Always wear personal protective equipment (PPE): safety glasses, gloves, and sturdy footwear
- Use clamps to secure materials when cutting or drilling
- Handle glass tubes carefully – they break easily and can cause injury
- Work in a ventilated area when using the burner for soldering
- Keep a fire extinguisher nearby when soldering
- Disconnect power tools when changing accessories
A family of five in Arusha requires a solar water heater. Each person uses 60 litres of hot water daily.
Calculation:
- Total daily demand = 5 persons × 60 litres = 300 litres
- Each evacuated tube can heat approximately 15-20 litres per day in Tanzanian conditions
- Number of tubes needed = 300 ÷ 17.5 ≈ 17 tubes (round up to 20 for safety margin)
Design specifications:
- Collector orientation: True north
- Tilt angle: 10° (approximately Arusha's latitude)
- Storage tank capacity: 300 litres minimum
In Tanzania, a small guesthouse in Dodoma might install an evacuated tube solar water heater to provide hot water for tourists. With electricity costs exceeding TZS 300 per kWh, using solar heating can save the owner over TZS 150,000 monthly compared to an electric geyser. The system pays for itself within 2-3 years while providing reliable hot water even during power outages, which are common in many rural and peri-urban areas.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Make black-body surface
- Make copper tubing under blackbody surface
- Cover evacuated tube collector solar water heater with transparent glass.
- Perform plumbing works
- Test the
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Evacuated tube collector solar water heater is constructed as per required standards and procedures.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to:
- Interpret the drawings
- Assemble evacuated tube collector solar water heater.
- Principles: The principles of:
- evacuated tube
Swali
In the Southern Hemisphere, which direction should an evacuated tube collector solar water heater face?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado