Mada za sehemu hiiDeveloping solar heaterMada 3
- Making flat plate collector solar water heater
- Making evacuated tube collector solar water heater
- Making heat pump system solar water heater
Heat Pump System Solar Water Heater
A heat pump system solar water heater is a device that uses energy from the sun to heat water for domestic use. Unlike simple solar collectors, a heat pump system includes a compressor and refrigerant cycle that boosts the water temperature efficiently. This study note covers the factors that affect its design and the step-by-step process of assembling one.
Before constructing a heat pump solar water heater, several factors must be considered:
1. Water Demand
- The number of people in the household determines daily hot water needs
- Average person uses 30–50 litres of hot water per day
- A family of five requires approximately 150–250 litres daily
2. Collector (Panel) Size
- Larger collectors capture more solar energy
- For a family of five, a collector area of 2–3 square metres is typical
- The size must match the hot water storage tank capacity
3. Location and Orientation
- The collector must face true north in the Southern Hemisphere (Tanzania)
- Optimal tilt angle equals the latitude of the location (approximately 5°–10° for most of Tanzania)
- Avoid shading from trees or buildings
4. Climate Conditions
- Areas with more sunshine allow smaller systems
- In cooler highland areas, larger collectors or backup heating may be needed
The following tools and safety gear are needed for assembly:
| Category | Tools and Equipment |
|---|---|
| Cutting | Handsaw, metal sheet scissors, copper tubing cutter, PPR-pipe scissors |
| Drilling | Set of drill bits, Forster drill bit |
| Fastening | Screwdriver set, set of wrenches, set of hammers |
| Clamping | Right angle clamps |
| Finishing | Paint brushes, silicon gun |
| Joining | Burner and soldering equipment, PP-R pipe welding kit |
| Pipe Work | Copper pipe bending tools |
| Testing | Multimeter |
| Measuring | Measuring tape |
| Safety | Set of PPEs (gloves, goggles, dust mask, safety boots) |
Step 1: Construct the Frame
- Measure and cut metal sheets to the required frame dimensions
- Use metal sheet scissors for cutting
- Secure corners using rivets or welding
- Ensure the frame is square and level
Step 2: Build the Absorber Plate
- Cut copper tubing to form a serpentine (winding) pattern
- Use a copper pipe bender to create smooth curves
- Lay the tubing on a dark-coloured absorber plate (typically black-painted copper or aluminium)
- Secure the tubing to the plate using clips or soldering
- The absorber plate must have a selective coating to maximise heat absorption
Step 3: Install the Glazing
- Cut transparent glass or polycarbonate sheet to cover the absorber
- Place the glazing material over the absorber plate
- Seal all edges with silicon to prevent air and moisture entry
- The glazing creates a greenhouse effect, trapping heat inside
Step 4: Connect Piping
- Connect the hot water outlet pipe from the absorber to the storage tank
- Connect the cold water inlet from the water supply to the tank
- Use PPR pipes for main plumbing and copper tubing for the collector
- Insulate all exposed pipes to reduce heat loss
- Install a circulation pump if using a forced circulation system
Step 5: Install the Heat Pump Unit
- Position the heat pump compressor unit near the storage tank
- Connect the refrigerant lines between the evaporator and the water tank coil
- Install the evaporator coil where it can receive ambient air
- Connect electrical wiring using proper gauge cables
- Test with a multimeter before powering on
Step 6: Final Assembly and Testing
- Check all connections for leaks
- Insulate the storage tank with suitable material
- Install temperature sensors and controls
- Fill the system with water and test operation
- Monitor temperatures at collector and tank outlets
A household in Arusha (latitude 3.4° S) has five family members. They want to install a heat pump solar water heater.
Calculate the required collector area:
- Daily hot water needed: 5 persons × 40 litres = 200 litres
- Each square metre of collector can heat approximately 50–70 litres per day in Tanzanian conditions
- Required collector area = 200 ÷ 60 ≈ 3.3 square metres
Design specifications:
- Collector orientation: True north
- Tilt angle: 5°–10° (latitude of Arusha)
- Storage tank capacity: 200–250 litres
- Use 2.5 mm² copper tubing for the absorber
This system will provide sufficient hot water while the heat pump boosts temperature during cloudy periods.
- Always wear PPE including gloves, goggles, and safety boots
- Use proper ventilation when soldering or using burners
- Disconnect electrical supply before working on heat pump components
- Handle refrigerants only in well-ventilated areas
- Secure heavy components properly when mounting
The heat pump solar water heater combines solar thermal collection with heat pump technology to provide reliable hot water. Success depends on proper system sizing based on water demand, correct collector orientation, careful assembly using appropriate tools, and thorough testing. Regular maintenance ensures long-term efficiency.
In many Tanzanian towns like Mwanza or Dodoma, small guesthouses and restaurants can use heat pump solar water heaters to provide hot water for guests while reducing electricity costs. For example, a small restaurant with 10 rooms might install a 300-litre system costing around TZS 2,500,000, which pays for itself within three years through savings on electric water heating bills. This also attracts eco-conscious tourists who prefer accommodations using renewable energy.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Make black-body surface
- Assemble heat pump system solar water heater
- Make copper tubing under blackbody surface
- Cover transparent glass on black-body surface.
- Perform plumbing works
- Test Make copper tubing under black body surface
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Make copper tubing under black body surface is constructed required standards and procedures.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The students should explain how to:
- Interpret drawings
- Assemble copper tubing under blackbody surface
Principles: The explain principles of heat pump system solar water heater
Theories: the students should be able to
- Importance of heat pump
- Procedure of making heat pump
- Application of heat pump
Swali
According to the source material, a family of five persons typically requires how much daily hot water?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado