Mada za sehemu hiiDeveloping solar parabolic concentratorMada 2
- Making stationary concentrating collectors
- Making sun tracking concentrating collectors
Stationary concentrating collectors are solar thermal devices that focus sunlight onto an absorber to heat water or other fluids without moving parts. Unlike tracking collectors, they remain fixed in position and rely on their angle and design to capture sunlight effectively throughout the day.
Before assembling a stationary concentrating collector, several factors must be considered:
- Water demand: The amount of hot water needed determines the size of the collector and storage tank. A larger household or small business requires a bigger collector area.
- Panel size: The collector surface area must be sufficient to capture enough solar energy to meet the heating requirements.
- Location: The installation site must receive unobstructed sunlight for most of the day. Shadows from buildings or trees reduce efficiency.
- Orientation: In Tanzania, collectors should face true north to capture maximum sunlight. The ideal tilt angle equals the latitude of the location (approximately 6° to 12° south of the equator for most of Tanzania).
1. Constructing the Frame
The frame provides structural support and holds the reflector and absorber in position. It is typically made from galvanized iron or aluminum angles.
- Cut frame members to the required dimensions using a handsaw.
- Join the frame pieces using bolts, nuts, and washers.
- Ensure the frame is square and rigid.
2. Preparing the Absorber Plate
The absorber plate absorbs solar radiation and converts it to heat. Black-painted metal sheets are commonly used.
- Cut a metal sheet (such as aluminum or copper) to fit inside the frame.
- Clean the surface thoroughly to remove dirt and grease.
- Apply a black matte paint or selective coating to improve solar absorption.
- Attach copper pipes to the absorber plate using brackets or clips for efficient heat transfer.
3. Installing Pipes and Connections
Proper piping ensures heated water circulates from the collector to the storage tank.
- Connect inlet and outlet pipes to the absorber plate using appropriate fittings.
- Apply thread seal tape or pipe dope to prevent leaks.
- Insulate exposed pipes to minimize heat losses.
- Install a circulating pump if using a forced circulation system.
4. Installing the Glazing
The glazing cover allows sunlight to pass through while reducing heat loss to the environment.
- Cut tempered glass or transparent plastic sheet to size.
- Place the glazing material over the absorber and secure it to the frame using glazing clips or silicone sealant.
- Ensure a tight seal to prevent air infiltration and moisture entry.
5. Insulating the Collector
Insulation reduces thermal losses from the back and sides of the collector.
- Apply fiberglass or mineral wool insulation to the rear panel.
- Seal all edges to prevent water penetration.
The following tools are required for assembly:
- Drill and drill bits
- Forster drill bit (for holes)
- Screwdriver set
- Set of clamps
- Handsaw
- Paint brushes
- Burner and soldering equipment
- Hammers
- Multimeter
- Measuring tape
- Wrench set
- Personal Protective Equipment (PPEs): gloves, safety goggles, dust mask, closed shoes
- Always wear appropriate PPE when cutting, drilling, or soldering.
- Work in a well-ventilated area when using paints or solvents.
- Secure materials with clamps before cutting or drilling.
- Handle glass sheets carefully to avoid breakage and cuts.
- Disconnect power tools when changing accessories.
After assembly, test the collector:
- Check all connections for leaks by pressurizing the system with water.
- Use a multimeter to verify electrical connections if a pump is installed.
- Measure the water temperature rise using a thermometer on a sunny day.
- Use an infrared thermometer to verify the absorber temperature reaches expected values.
A well-constructed stationary concentrating collector achieves higher temperatures than flat-plate collectors because the reflective surface concentrates sunlight onto a smaller absorber area. The concentration ratio (the ratio of collector aperture area to absorber area) typically ranges from 2 to 10 for stationary concentrators.
In Tanzania, small businesses such as guesthouses in Arusha or restaurants in Dar es Salaam commonly use stationary concentrating solar collectors to heat water for guest showers and kitchen use. For example, a guesthouse with 10 rooms might install a 2 m² collector connected to a 200-liter storage tank, reducing electricity costs by up to 50,000 TZS per month compared to electric geysers while providing reliable hot water during daylight hours.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Choose proper materials.
- Perform curving
- Make cooking supporting structure.
- Make parabolic base structure
- Perform welding
- Assemble reflectors to shape focal point
Tathmini ya matokeo
stationary concentrating collectors is made as per requirements
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The students should explain how to:
- Identify drawings
- Fabricate stationary concentrating collectors
Principles: The students should explain principles of :
- Light reflection
- Light absorption.
Theories: The explain:
Swali
In Tanzania, stationary concentrating solar collectors should face which direction to capture maximum sunlight?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado