Mada za sehemu hiiMaking seamsMada 5
An open flat seam is a type of seam used in leather goods and footwear where two pieces are stitched together face to face and the seam is then opened out, with one seam allowance pressed flat to each side. This creates a smooth, comfortable finish that does not bulk up — making it ideal for shoes and bags that touch the skin.
A stitch is one loop of thread passing through the material. A seam is the line along which two pieces are joined by a row of stitches. The seam allowance is the strip of material between the stitch line and the cut edge. It must be wide enough for the stitches to hold without tearing out, but not so wide that it makes the seam bulky.
- The seam lies flat against the material
- Seam allowances are opened out, one to each side, and kept narrow
- Provides a neat and professional appearance
- Commonly used on shoe uppers, bags, and belts
| Seam | How it is made | Typical use |
|---|---|---|
| Open flat seam | Stitched face to face, then opened with the allowances pressed flat to each side | Back seams of shoes, bag panels |
| French seam | An open seam with an extra row of stitching on each side of the join, through the allowances | Strong, decorative seams on bags and uppers |
| English seam | Stitched twice so that the raw edges are closed inside the seam | Fabric linings that fray |
| Open edge seam | One piece is laid over the other and stitched, leaving the cut edge showing | Straps, belts, joining a vamp to a quarter |
| Zigzag seam | Two edges are placed side by side, touching, and joined by a zigzag stitch across the join | Linings and thin leather where no bulk is wanted |
Choose the seam from the working drawing. It shows where the seam lies on the product, which seam is required and how wide the seam allowance is.
- Thread: use a strong polyester or nylon thread. Thick, firm leather needs a thicker thread than thin leather or fabric.
- Needle: for leather, fit a leather-point machine needle, whose cutting point slices a neat hole; for fabric linings use a normal round-point needle. A thick thread needs a thicker needle, so that the thread runs freely through the eye.
- Setting the machine: with the power switched off, fit the needle the right way round, push it fully up and tighten the needle screw with the screwdriver. Thread the machine and insert the wound bobbin.
- Stitch length: set the stitch-length regulator to about 3 mm, which gives 3 to 4 stitches in each centimetre. Stitches that are too short cut the leather like a row of perforations; stitches that are too long make a weak seam.
- Test first: sew a few centimetres on two offcuts of the same leather. The stitches should look the same on both sides, with no loops. If loops show underneath, increase the needle-thread tension a little; if they show on top, reduce it.
For a hand-sewn seam, use a harness needle and waxed thread, with a thimble to push the needle.
Step 1: Prepare the Leather Pieces
Cut two pieces of leather to the required size and shape. Ensure the edges are clean and straight.
Step 2: Mark the Seam Allowance
Mark a consistent seam allowance (usually 6–8 mm) along the edge of both pieces, on the wrong (flesh) side, using a ruler and scratch awl or pencil.
Step 3: Align the Pieces
Place the two leather pieces together with the right (grain) sides facing each other and the edges level. Hold them steady with clips. Do not use pins outside the seam allowance, because pin holes in leather are permanent.
Step 4: Stitch the Seam
Using a saddle stitch or machine stitch, sew along the marked seam line. Keep stitches even and the same size apart. Fasten both ends of the seam: on a machine, sew back over the last three or four stitches, or pull the thread ends through to the wrong side and knot them; by hand, stitch back through the last two holes. Trim the thread ends.
Step 5: Trim the Seam Allowances
Using sharp scissors or a craft knife, trim the seam allowances down to about 3 mm from the stitch line. Be careful not to cut the stitches.
Step 6: Press the Seam Flat
Open the two pieces out flat with the wrong (flesh) side facing up. Fold one seam allowance to each side and flatten the seam by tapping along it with a mallet on a smooth, hard surface. Do not use a hot iron, which can shrink and harden leather. This opens the seam and makes it lie flat.
Step 7: Apply Finish (Optional)
For extra durability, apply a thin coat of leather adhesive under each seam allowance and press it down, so that the seam stays open. A strip of reinforcing tape may also be stuck over the seam on the wrong side.
Step 8: Clean the Seam
Cut off all loose thread ends close to the seam. Rub away any adhesive that has squeezed out and wipe off marking lines with a soft, dry cloth, so that the right side shows only a neat, closed join.
Suppose you are joining two leather panels along one long edge to make the outside of a wallet, the panels measuring 15 cm × 10 cm each.
- Place the two panels with right sides together.
- Mark a 6 mm seam allowance along the long edge to be joined.
- Stitch along the marked line and fasten both ends.
- Trim both seam allowances to 3 mm.
- Open the panels, fold one allowance to each side and tap the seam flat with a mallet.
The result is a neat, flat seam that will not irritate the hand when the wallet is held.
- Always wear gloves when handling sharp tools.
- Use a thimble to protect your fingers while hand-stitching.
- Keep your work area clean and free of loose scraps.
- Dispose of leather cuttings in the dustbin.
- Work in a well-ventilated area, and wear a nose mask when using adhesive or sweeping up leather dust.
- At the sewing machine, keep your fingers away from the needle, tie back long hair and loose sleeves, and take your foot off the pedal before you move your hands near the needle.
- Switch the machine off before threading it, changing the needle or cleaning it.
- Cut away from your body with knives and keep the blade covered when it is not in use.
- Use the sewing machine only under supervision.
For a needle prick or a small cut, stop work, wash the wound with clean water and soap, press on it with a clean cloth until the bleeding stops, and cover it with a clean dressing. If a cut is deep, or a broken machine needle is stuck in a finger, switch off the machine, do not pull the needle out, and get help at once so that the injured person can be taken to a health facility. Report every injury.
- With the power off, brush lint and leather dust from around the needle plate and bobbin case of the machine, then cover it
- Wipe knives, scissors and the mallet and return them, with the screwdrivers, to their places
- Put leather offcuts and thread ends in the dustbin, and put broken needles in a closed tin first; keep larger offcuts for test pieces
- Sweep the floor and mop up any spills
- Store leather flat or loosely rolled, never folded, in a dry place out of the sun, and close adhesive containers tightly
- Placing the pieces wrong sides together, so that the seam allowances end up on the outside.
- Leaving seam allowances too wide — this creates bulk.
- Trimming too close to the stitches — you may cut the thread.
- Skipping the pressing step — the seam will not lie flat.
A cobbler in Arusha often uses open flat seams when repairing shoes because this technique creates smooth seams that do not rub against the foot, keeping the shoe comfortable to wear. By mastering this skill, you can also start a small shoe repair business or make leather bags and belts to sell at the local market.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select materials
- Interpret different drawing
- Select tools and equipment
- Select the required type of seams to suit the type of design.
- Select the correct type of threads and needles to suit the needed material.
- Cut sample leathers
- Set and adjust a sewing machine
- Select and set a stitch length
- Perform different types of seams
- Clean seams
- Observe safety
- Clean tools and equipment
- Store materials
- Store tools and equipment
Tathmini ya matokeo
Open flat seams are formed according to the required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should clearly explain how to:
- Make different types of seams using different types of leather material
- Select different types of seams
- Adjust the machine for different seams
Principles: The student should correctly explain the principles of:
- Setting machine seams
- Preparing materials for different seams
- Making seams
- Finishing and thread ends
Theories: The student should correctly explain:
- The difference between seams and stitches
- Seam allowances
- The use of different seams
- Types of threads, needles, and materials used while seaming
- French seams, English seams, open edge and zigzag seams and their differences
Circumstantial knowledge:
Detailed knowledge of:
- Safe precautions pertaining on seaming operations
- Safe handling of tools and equipment
- First aid.
- Waste disposal
Swali
What is an open flat seam?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado