Mada za sehemu hiiDesigning intermediate patterns for leather goods projectsMada 5
A leather folder is a flat case that opens like a book and holds documents, certificates or a writing pad. Folder patterns are the full-size paper shapes, one for each part of the folder, that are used to mark and cut the leather, lining and stiffeners. Good patterns decide the quality of the product: every folder cut from them will be the same size, and any mistake in a pattern is repeated in every folder.
- Outer cover – one piece that forms the front, the spine and the back
- Lining – covers the whole inside of the cover
- Pockets – a large pocket on one side for papers, and often a slot on the other side to hold a writing pad
- Small parts – card pocket, pen loop and closing tab, if the design has them
- Stiffeners – two boards, one for the front and one for the back, that keep the folder flat
- Tracing paper – thin and see-through; used for the main sketch and for copying lines
- Draft paper – cheap paper for working out sizes
- Soft manilla paper – easy to draw on, cut and correct; used for the first master pattern
- Hard manilla paper – stiff and long-lasting; used for the final patterns that are handled many times
- Masking tape – holds tracing paper still while you draw
You also need a tape measure, rulers, a square, pencils, an eraser, a tracing wheel, scissors, a cutting knife, a cutting board, a set of punches and a hammer.
A leather article can be designed in three ways: by copying a prototype sample, by working from a sketch or picture, or by working from the measurements a customer gives. Whichever way you use, first imagine the finished folder: how it opens, what it holds, and which colours of leather, lining and thread go together. Compare colours in daylight, because similar shades can look the same in poor light.
Folders are made to fit standard paper sizes. A4 paper is 210 mm × 297 mm and A5 paper is 148 mm × 210 mm. The folder must be a little larger than the paper it holds.
- Take measurements. Measure the paper, pad or sample folder. Add about 15 mm of clearance on each side and about 10 mm at the top and at the bottom. Decide the width of the spine, usually about 20 mm.
- Draw the main sketch on tracing paper. Tape the tracing paper over draft paper. With ruler and square, draw the cover lying open at full size: front panel, spine and back panel. Check that the shape is a true rectangle by measuring both diagonals; they must be equal.
- Trace the master pattern onto soft manilla. Lay the sketch on soft manilla and run the tracing wheel along every line. Go over the dotted lines in pencil and check each measurement again.
- Cut the master pattern on hard manilla. Transfer the outline to hard manilla and cut it on the cutting board with the knife against a steel ruler. This master shows the finished size of the folder, with no allowances.
- Develop the parts. From the master, draw each separate part and add its allowances. An edge that will be folded over needs about 10 mm extra. Edges that are stitched together as cut edges need no extra. Stiffeners are cut about 3 mm smaller than the panel all round, and the lining slightly narrower than the cover so that it does not wrinkle when the folder closes.
- Transfer the parts to hard manilla and cut them out carefully. Smooth, straight edges on the pattern give smooth, straight edges on the leather.
- Insert marking points. Cut small notches at the top and bottom of the two spine fold lines and at the centre of each long edge. Punch small holes at the corners of each pocket position and at the pen loop and closing tab positions.
- Label every pattern. Write the name of the part, the style, the size (A4 or A5), the material (leather, lining or board) and how many to cut.
- Grade the patterns. Grading means making the same design in another size. Work out the new finished size from the new paper size, then add the same allowances as before; allowances do not grow or shrink with the size.
- Group the patterns in pairs. Put matching parts together, such as the two stiffeners and the left and right pockets, and check each pair edge to edge.
- One panel: width 210 + 15 + 15 = 240 mm; height 297 + 10 + 10 = 317 mm.
- Open cover, finished size: 240 + 20 + 240 = 500 mm wide and 317 mm high.
- Outer cover pattern with a 10 mm folded edge all round: 500 + 20 = 520 mm wide and 317 + 20 = 337 mm high.
- Stiffener pattern (cut 2): 240 - 6 = 234 mm wide and 317 - 6 = 311 mm high.
- Large pocket pattern: 240 mm wide and 200 mm high, plus 10 mm on the top edge for folding, so 240 mm × 210 mm.
- Graded to A5, one panel becomes 148 + 30 = 178 mm wide and 210 + 20 = 230 mm high; the spine and the allowances stay the same.
- Wear your overall or dust coat and safety boots. Cut on the cutting board, hold the ruler with your fingers behind its edge, and cover the blade when the knife is not in use.
- Hold punches upright and keep your fingers clear of the hammer.
- First aid: for a small cut, clean it under running water, press on it with a clean cloth until the bleeding stops, cover it with a plaster and report it. For a deep cut, keep pressing and get medical help at once.
- Rub stray pencil marks off the patterns and wipe the tools before putting them away.
- Tie each set of patterns through a punched hole or keep it in a labelled plastic box, stored flat and dry. Never fold a pattern.
- Keep large paper offcuts for small patterns and put the rest in the paper bin. Put used blades in a closed container, never loose in the bin.
- Drawing without a square, so that corners are not true right angles and the folder closes crookedly
- Forgetting the allowance on folded edges, so that the finished folder is too small
- Leaving out the spine, so that the folder cannot close over the papers
- Unlabelled patterns, which are easily mixed between sizes
A small leather workshop in Arusha receives an order for 20 document folders for a local company. The craftsperson makes one accurate set of patterns on hard manilla and uses it to mark and cut every piece. All 20 folders come out the same size, little leather is wasted, and the patterns are stored ready for the next order.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to correctly:
- Distinguish different colours
- Identify the required design
- Select tools and equipment
- Imagine the desired products
- Select prototype samples
- Identify the required materials
- Prepare tracing papers
- Take measurements
- Interpret measurements into sketches
- Draw the main sketch on tracing papers
- Trace master patterns on soft manilla papers
- Cut master patterns on hard manilla papers
- Develop various parts of the designs
- Transfer cut pattern parts into hard manilla papers
- Grade patterns
- Insert marking points
- Group patterns in pairs
- Observe safety
- Clean patterns
- Clean tools and equipment
- Store patterns
- Store equipment
Tathmini ya matokeo
A folder patterns made as per designs specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should correctly:
- Take measurements
- Trace different designs
- Trace standard size.
- Transform sketches correctly
- Produce master patterns correctly
- Develop patterns correctly
- Grade patterns correctly
Principles: The student should correctly explain the principles of:
- Designing
- Unit standard size chart
- Geometry
Theories: The student should explain:
- Ways of designing leather goods.
- The influence of patterns.
- Grading techniques
- Importance of precise and detailed work while making patterns
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling tools and equipment
- Safe handling of patterns
- First aid
- Waste disposal
Swali
Which material is used for the final master pattern because it is stiff and long-lasting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado