Mada za sehemu hiiDesigning intermediate patterns for leather goods projectsMada 5
- Making wallet patterns
- Making folder patterns
- Making travelling bag patterns
- Making briefcase patterns
- Making simple leather jacket patterns
A leather jacket pattern is a paper template that shows exactly where to cut each piece of leather so the finished jacket will fit a person's body correctly. Before we can make a good pattern, we must first take accurate body measurements.
A design brief is a short written description of what is to be made. For a simple leather jacket it states who will wear it, the style (for example a plain hip-length jacket with a front zip and two pockets), the type and colour of leather, the colours of the lining, thread and zip, and the size. A prototype sample jacket or a picture helps you to imagine the finished product and to list its parts before any measuring begins.
Leather is expensive compared to fabric, so every cut must be precise. If measurements are wrong, the jacket will not fit and the leather may be wasted. Taking good measurements is the first and most important step in pattern making.
To draft a simple leather jacket pattern, you need to take the following body measurements:
- Chest circumference – measure around the fullest part of the chest
- Waist circumference – measure around the natural waistline
- Back length – measure from the base of the neck down to the waist
- Shoulder width – measure from one shoulder bone to the other across the back
- Sleeve length – measure from the shoulder bone, over the slightly bent elbow, down to the wrist
- Armhole depth – measure down the centre back from the bone at the base of the neck to the level of the armpit
- Jacket length – measure down the centre back from the base of the neck to where the jacket should end
- Neck circumference – measure around the base of the neck
- Ask permission before you measure a classmate. The person should wear light clothing and stand upright with arms relaxed at their sides.
- Use a tape measure and keep it horizontal (parallel to the floor) when measuring around the body.
- Do not pull the tape too tight — it should rest comfortably against the body.
- Write down each measurement immediately in centimetres.
- Add ease allowance later when drafting the pattern (see the section on ease below).
Use a simple table to record measurements clearly:
| Measurement | Symbol | Value (cm) |
|---|---|---|
| Chest circumference | C | ___ |
| Waist circumference | W | ___ |
| Back length | BL | ___ |
| Shoulder width | SW | ___ |
| Sleeve length | SL | ___ |
| Armhole depth | AD | ___ |
| Neck circumference | N | ___ |
| Jacket length | JL | ___ |
The body measurements alone are too tight for a wearable jacket. You must add ease allowance — extra centimetres that allow the jacket to be comfortable when worn.
For a simple leather jacket:
- Chest ease: add about 10–12 cm, because a jacket is worn over other clothes
- Waist ease: add about 8–10 cm
- Back length: add about 2 cm
- Sleeve length: add about 2 cm, so that the sleeve still covers the wrist when the arm bends
Leather does not give like knitted fabric, so a leather jacket with too little ease is hard to move in.
Mwanajuma wants to make a simple leather jacket for her brother Hamisi. She takes his measurements and records them:
| Measurement | Value (cm) |
|---|---|
| Chest | 96 |
| Waist | 84 |
| Back length | 42 |
| Shoulder width | 44 |
| Sleeve length | 58 |
| Jacket length | 62 |
She adds ease allowance:
- Finished chest measurement: 96+10=106 cm
- Finished waist measurement: 84+8=92 cm
- Finished back length: 42+2=44 cm
The back panel must be as wide as half the finished chest: 106÷2=53 cm. Because the jacket is the same on both sides, Mwanajuma drafts only half of the back, 26.5 cm wide, and marks its straight edge as the centre back line.
- Draw the main sketch full size on tracing paper taped over draft paper. Start with the back piece, using a quarter of the finished chest for its half-width and the jacket length for its height.
- Add seam allowances (about 1–1.5 cm) all around each piece.
- Draw the front pieces with an overlap for buttons, or a straight edge for a zip, then develop the other parts: sleeves, collar, facings, cuffs and pockets. Leather skins are small, so a large piece such as the back is often divided into panels (for example a yoke and a lower back), each with its own pattern.
- Insert the marking points: notches where the sleeve meets the shoulder and side seams, the centre back and centre front, the pocket positions and the button or zip-end positions.
- Trace the checked pieces onto soft manila as master patterns, then transfer them to hard manila and cut them out. Label each piece with its name, the size and how many to cut.
- Grade the patterns to other sizes using a standard size chart: add or take away the difference between sizes (for example about 4 cm on the chest between one size and the next), shared evenly between the pieces.
- Group the patterns in pairs (left and right fronts, the two sleeves, the two cuffs) and check each pair edge to edge.
Each pattern material has its own job: tracing paper is thin and see-through, for drawing and copying the main sketch; soft manila is easy to draw on and correct; hard manila is stiff and keeps its shape through many uses.
- Always use a cutting board when cutting pattern paper with a knife.
- Wear safety gloves when handling sharp tools.
- Keep your work area clean and organised.
- For a small cut, clean it under running water, press on it with a clean cloth until the bleeding stops, cover it with a plaster and report it. For a deep cut, keep pressing and get medical help at once.
- Rub out stray pencil lines and brush dust off the patterns.
- Wipe rulers, squares and the cutting board, cover knife blades, and return every tool to its place.
- Hang each set of patterns through a punched hole, or store it flat in a labelled plastic box, in a dry place. Do not fold patterns.
- Keep large paper offcuts for small patterns and put the rest in the paper bin. Put used blades in a closed container, never loose in the bin.
- Taking measurements over thick clothing, which gives wrong sizes.
- Forgetting to add ease allowance, making the jacket too tight.
- Rushing the recording of measurements and mixing up numbers.
- Using a torn or stretched tape measure.
In Tanzania, many tailors and small workshops in Arusha and Dar es Salaam make leather jackets for customers. A tailor who knows how to take accurate body measurements can offer measuring and pattern making as a paid service before any leather is cut. This skill helps a young person start a small leather goods business, as good patterns mean fewer mistakes and less wasted expensive leather.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Distinguish colours
- Identify the required design
- Set a design brief
- Select appropriate tools and equipment
- Imagine the desired product
- Select a prototype sample
- Identify the required materials
- Prepare a tracing paper
- Take measurements
- Interpret measurements into sketches
- Draw the main sketch on the tracing paper
- Trace master patterns on soft manilla papers
- Cut master patterns on hard manilla papers
- Develop various parts of the design
- Transfer cut patterns parts into hard manilla paper
- Grade patterns
- Insert marking points
- Group patterns in pairs
- Observe safety
- Clean patterns
- Clean tools and equipment
- Store patterns correctly
- Store equipment correctly
Tathmini ya matokeo
Patterns of simple leather jackets are designed based on their measurements
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should be able to:
- Create designs correctly
- Take measurements.
- Trace standard size
- Transform sketches
- Produce master pattern
- Develop patterns
- Grade patterns
Principles: The student should clearly explain the principles of:
- Designing
- Unit standard size chart
Theories: The student should correctly explain:
- Types of pattern materials
- Grading techniques
- The importance of precision and detail when making patterns
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling of tools and equipment
- Safe handling of patterns
- First aid
- Waste disposal
Swali
Why must body measurements be especially accurate when a jacket is to be made of leather?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado