Mada za sehemu hiiDesigning intermediate patterns for leather goods projectsMada 5
- Making wallet patterns
- Making folder patterns
- Making travelling bag patterns
- Making briefcase patterns
- Making simple leather jacket patterns
A travelling bag pattern is a full-size paper template that guides you to cut leather pieces accurately before stitching them together. Making an accurate pattern is the foundation of producing a professional-looking travelling bag, because any error in the pattern will be reproduced in the finished product.
Before starting, gather the following from your workshop:
- Draft paper or soft manila paper for the draft pattern
- Hard manila paper for the final pattern
- Tape measure
- Rulers (straight ruler and set square)
- Pencils and eraser
- Tracing wheel and tracing paper
- Scissors and cutting knife
- Cutting board
- Masking tape
- Set of punches and hammer (for marking points and hanging holes)
- Notebook for recording measurements
A set of patterns begins with a clear design. Study a prototype sample bag or a picture, and imagine the finished product: its shape, its size, how it opens, where the handles and pockets sit, and the colours of the leather, lining, thread and fittings. Travelling bags belong to the heavy (travel) group of leather goods, so their patterns are large and must be very accurate. Draw the main sketch of the bag on tracing paper taped over draft paper, write the measurements on it, and list every part that needs a pattern.
Each pattern material has its own job. Tracing paper is thin and see-through, for drawing and copying lines. Draft paper and soft manila are easy to draw on and correct, for working patterns. Hard manila is stiff and keeps its shape, for the final patterns that are used again and again.
A travelling bag pattern is based on three main measurements:
- Length – the horizontal distance across the bag when laid flat
- Width – the side-to-side depth of the bag
- Height – the vertical measurement from bottom to top of the bag
Always add seam allowance of approximately 1–1.5 cm to all edges so that pieces can be joined together cleanly.
Step 1: Determine the Bag Dimensions
Decide on the finished dimensions of your travelling bag. For a small weekend bag, common dimensions might be:
- Length: 45 cm
- Width: 20 cm
- Height: 35 cm
Step 2: Draw the Main Body Panel
The main body of the bag consists of two large rectangular panels — the front and the back.
-
On draft paper, draw a rectangle with:
- Width = bag height + seam allowance = 35 cm + 2 cm = 37 cm
- Length = bag length + seam allowance = 45 cm + 2 cm = 47 cm
-
Label this rectangle as "Main Body Panel (Front)" and "Main Body Panel (Back)".
Step 3: Draw the Side Panels
Side panels give the bag its width and depth.
-
Draw a rectangle with:
- Width = bag height + seam allowance = 37 cm
- Length = bag width + seam allowance = 20 cm + 2 cm = 22 cm
-
You will need two side panels.
Step 4: Draw the Bottom Panel
- Draw a rectangle with:
- Width = bag width + seam allowance = 22 cm
- Length = bag length + seam allowance = 47 cm
Step 5: Draw a One-Piece Gusset (Alternative)
A gusset is the part that gives a bag its depth. Instead of two side panels and a separate bottom panel, many travelling bags use one long gusset strip that runs down one end, along the bottom and up the other end.
- Add the three lengths the strip must cover: 35+45+35=115 cm, plus 2 cm seam allowance = 117 cm
- Draw a strip 117 cm long and 22 cm wide (bag width + seam allowance). Mark the two points where the strip turns the bottom corners, so that they can be matched to the corners of the front and back panels.
- If the bottom corners of the front and back panels are rounded, measure round the curved edge with the tape measure instead, so that the strip is exactly as long as the edge it joins.
Step 6: Transfer to Hard Manila Paper
- Place the hard manila paper on the cutting board.
- Lay the draft over the manila and run the tracing wheel along every line to transfer all the pattern pieces.
- Cut out each pattern piece carefully using scissors or a cutting knife.
- Insert the marking points: notches at the centre of each edge and at the corners for matching panels, and small punched holes for the handle, pocket and zip-end positions.
- Label each piece clearly: name of the part, bag style, size, and how many to cut.
- Group the patterns in pairs: front with back, left side with right side, and the two handles. Check each pair edge to edge; the two must be exactly the same.
Step 7: Grade the Patterns
Grading means making the same design in other sizes, such as small, medium and large. Increase or reduce the length, width and height of the bag by the chosen step (for example 5 cm in length), work out the new size of every part, and keep the seam allowance the same on every size. Check again that edges which will be joined match, then label each set with its size.
A student making a bag 45 cm long, 20 cm wide and 35 cm high for a weekend trip needs these pattern pieces:
| Piece | Length (cm) | Width (cm) |
|---|---|---|
| Front panel | 47 | 37 |
| Back panel | 47 | 37 |
| Left side panel | 22 | 37 |
| Right side panel | 22 | 37 |
| Bottom panel | 47 | 22 |
| Zip panel (cut 2) | 47 | 12 |
| Handle strip (cut 2) | 60 | 8 |
Each size already includes 1 cm seam allowance on every side. Each zip panel is half the bag width (10 cm) plus allowance, and the zip is stitched between the two. Each handle strip is folded in half along its length before stitching. After cutting the pieces from manila paper, the student adds notches at the centres and corners for easy assembly and labels every piece.
- Always double-check measurements before cutting the final patterns, because a wrong pattern wastes expensive leather.
- Mark seam allowance consistently on all pieces to ensure panels fit together properly.
- Use notch marks — small triangular cuts at edges — to align panels during assembly.
- Label every piece clearly to avoid confusion when cutting leather.
- Store patterns flat, or hang them through a punched hole, in a dry place. Do not fold or roll them, so that they stay accurate for future use.
- Wear your overall or dust coat and safety boots in the workshop.
- Use the cutting board when cutting paper to protect the workbench.
- Cut against a steel ruler, keep the fingers of your holding hand behind its edge, and never pull the knife towards that hand.
- Keep masks on when working with dusty materials.
- For a small cut, clean it under running water, press on it with a clean cloth until the bleeding stops, cover it with a plaster and report it. For a deep cut, keep pressing and get medical help at once.
- Rub out stray pencil lines and brush eraser dust off the patterns before storing them.
- Wipe rulers, squares and the cutting board, and return every tool to its place with knife blades covered.
- Keep large paper offcuts for small patterns and put the rest in the paper bin. Put used knife blades in a closed container, never loose in the bin.
In Tanzania, a craftsperson in Arusha who makes and sells leather bags can use accurate travelling bag patterns to produce multiple identical bags efficiently for a local craft market, reducing waste of expensive leather hides and increasing profitability. A student could also create custom-sized travelling bag patterns for family members or neighbours, earning income by offering a pattern-making service using locally available manila paper and basic tools.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify the required design
- Select appropriate tools and equipment
- Imagine the desired product
- Select the prototype sample
- Identify the required materials
- Prepare tracing papers
- Take measurements
- Interpret measurements into sketches correctly
- Draw the main sketch on a tracing paper
- Trace master patterns on soft manilla papers.
- Cut master patterns on hard manilla papers
- Develop various parts of the designs
- Transfer cut pattern parts into hard manilla papers
- Grade patterns correctly
- Insert marking points
- Group patterns in pairs
- Observe safety
- Clean patterns
- Clean tools and equipment
- Store patterns
- Store equipment
Tathmini ya matokeo
Travelling bag patterns are designed according to their specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should correctly explain:
- Create different designs
- Take measurements
- Trace different designs
- Trace standard size
- Transform sketches
- Produce master patterns
- Develop patterns
- Grade patterns
Principles: The student should explain the principles of:
- Designing
- Unit standard size chart
- Geometry
Theories: The student should clearly explain:
- Types of leather goods
- Types of pattern materials
- Ways of designing leather goods
- The influence of patterns
- Grading techniques
- The importance of precision and attention to details when making patterns
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling of tools and equipment
- Safe handling of patterns
- First aid
- Waste disposal
Swali
What is the main purpose of a travelling bag pattern?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado