Mada za sehemu hiiDesigning intermediate patterns for footwear projectsMada 4
- Making Oxford shoe patterns
- Making sandal patterns
- Making training shoe patterns
- Making military boot patterns
An Oxford is a laced shoe with closed lacing: the quarters, which carry the eyelets, are stitched under the vamp, so the lacing opens only a little way. (In a Derby shoe the quarters lie on top of the vamp.) All the patterns for an Oxford are developed from the shoe last, so that the flat pieces of leather will take the shape of the last when the shoe is made.
A simple cap-toe Oxford needs about eight main patterns:
Upper patterns
- Vamp – covers the front of the foot up to the start of the lacing
- Quarters (inside and outside) – cover the sides and heel and carry the eyelets
- Tongue – lies under the laces
- Toe cap – covers the toe end of the vamp; a plain Oxford has none
Lining patterns
- Vamp lining
- Quarter lining
Bottom patterns
- Insole – the base on which the upper is lasted
- Outsole – the part that touches the ground
Patterns for the toe puff and the heel stiffener may be added. The number changes with the style, but every upper and lining pattern is developed from one master pattern, called the standard.
- Foot anatomy: the toes; the joint (ball), which is the widest part and where the foot bends; the instep, which is the raised top of the foot; the heel; and the ankle bones. The top line of an Oxford must pass below the ankle bones, and the outside ankle bone is the lower of the two.
- Foot measurements: length from heel to longest toe with the person standing, girth around the joint, and girth around the instep.
- Imaginary lines on the last: the centre line down the front, the centre line down the back, the joint line across the widest part, and the feather edge, where the side of the last meets its bottom.
- Units: footwear is measured in millimetres. One continental size (Paris point) is 6.67 mm of length; one English size is 8.46 mm.
Shoe last, masking tape, tape measure, rulers and square, pencils and eraser, tracing paper and tracing wheel, scissors, a cutting knife, cutting board, set of punches and hammer, rasp file and plastic boxes. The pattern materials are draft paper for flattening the tape, manilla sheets for working patterns, and hard manilla or carton for the final patterns.
- Select the design and the last. Decide the style and the colours of the upper leather, lining and thread. Choose a last of the correct size with a toe shape that suits the design, and check that it is clean and undamaged.
- Cover the last with masking tape. Lay overlapping strips over the whole upper surface until no last shows, and smooth out every crease. Trim the tape neatly along the feather edge.
- Draw the main lines. Mark the centre line down the front and down the back. Mark the back height, about one-fifth of the length of the last above the bottom of the heel, and the vamp point, where the lacing will start.
- Sketch the design on the tape. Draw the top line, the curve where the vamp crosses the quarters, the toe cap line and the eyelet positions (usually five on each side).
- Remove the tape. Cut along the two centre lines with light pressure. Peel off the outside half and the inside half and stick each one flat on draft paper, working from the middle outwards. Make small cuts at the toe and along the bottom edge so that the tape lies flat.
- Cut the master pattern. Cut out the two shapes and lay one on the other. Where their outlines differ, draw a line midway between them. Add a lasting allowance of about 15 mm along the bottom edge, which is pulled under the insole during lasting. Prick the design lines through and cut this shape from manilla. This is the standard.
- Develop the upper patterns. Use tracing paper to copy each part from the standard, and add its allowances: about 8 mm where a part lies under another (the front of each quarter under the vamp, and the vamp under the toe cap), and about 5 mm on edges that will be folded, such as the top line. Fold the paper along the centre line to cut the vamp, toe cap and tongue, so that both halves match. The tongue runs from the vamp point to just above the top eyelets and is wide enough to cover the lacing gap.
- Develop the lining patterns. Trace them from the standard without the design lines. Add about 3 mm along the top line, to be trimmed off after stitching.
- Make the bottom patterns. Trace the bottom of the last exactly for the insole, with no allowance. For the outsole, draw about 4 mm outside the insole line all round; the extra is trimmed when the sole is finished.
- Transfer to hard manilla or carton and cut out each pattern. Smooth rough edges lightly with the rasp file.
- Insert marking points and labels. Punch the eyelet positions and prick small holes to show where the toe cap and vamp sit. Write on each pattern its name, the style, the size, and inside or outside.
- Grade and group. Grade the patterns to other sizes using the standard size chart, adding 6.67 mm of length for each continental size and keeping the allowances unchanged. Keep the patterns of each size together as a set.
A student makes patterns on a size 42 last. Its length is about 42 × 6.67 = 280 mm, so the back height is marked 280 ÷ 5 = 56 mm above the bottom of the heel. After taping, drawing and flattening, the student adds 15 mm of lasting allowance to the standard, 8 mm to the front of each quarter and 5 mm along the top line. For size 43 the patterns are graded to a last about 280 + 6.67 = 287 mm long.
- Cut the tape on the last with light pressure and keep your holding hand behind the blade.
- Cut patterns on the cutting board, and cover the blade when the knife is not in use.
- First aid: for a small cut, clean it under running water, press on it with a clean cloth until the bleeding stops, cover it with a plaster and report it. For a deep cut, keep pressing and get medical help at once.
- Peel all tape off the last, wipe the tools and the work table, and return everything to its place.
- Store each set of patterns flat in a labelled plastic box or hang it through a punched hole. Never fold a pattern.
- Put tape and paper offcuts in the bin, and used blades in a closed container.
A shoemaker in Arusha who can make accurate Oxford patterns can offer made-to-measure school and office shoes from locally tanned leather. Because the patterns are graded and stored by size, the same style can be repeated for many customers without starting again, which saves time and leather.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select appropriate tools and equipment
- Distinguish colours
- Identify the required design
- Select shoe lasts
- Prepare masking tape
- Prepare tracing paper
- Cover shoe lasts with masking tape
- Trace the shoe last based on their design
- Draw main lines
- Remove the traced masking tapes
- Stick on draft paper
- Sketch designs
- Cut master patterns
- Develop patterns
- Cut different parts of footwear patterns
- Transfer patterns into hand carton or manilla
- Grade patterns
- Insert marking points
- Group patterns into sizes
- Clean the work place
- Observe safety
- Clean the work place
- Clean tools and equipment
- Store patterns correctly
- Store tools and equipment correctly
Tathmini ya matokeo
Patterns of Oxford shoes are designed based on their specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should be able to:
- Take foot measurements correctly
- Mask shoe lasts.
- Trace different designs correctly
- Trace standard pattern lines
- Transform sketches
- Produce correct master patterns
- Develop patterns correctly
- Grade patterns correctly
Principles: The student should explain the principles of:
- Designing
- Taking foot measurements
- Pattern cutting
- Standard size chart
Theories: The student should explain:
- Types of footwear designs
- Types of pattern materials
- Imaginary lines on the lasts
- The units of measurements used in footwear making
- Designing techniques
- Foot anatomy
- The importance of precision and detail in making patterns
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling of tools and equipment
- Safe handling of patterns
- First aid
- Waste disposal
Swali
What distinguishes an Oxford shoe from a Derby shoe?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado