Mada za sehemu hiiDesigning intermediate patterns for footwear projectsMada 4
- Making Oxford shoe patterns
- Making sandal patterns
- Making training shoe patterns
- Making military boot patterns
A sandal pattern is a flat template, cut from paper or card, that gives the exact shape of one part of a sandal: the insole, the sole or a strap. The patterns are developed on a shoe last, the foot-shaped block on which the sandal is later built, so that every part fits the foot.
- Measuring and drawing: tape measure, rulers, square, pencils in different colours and an eraser
- Working on the last: shoe last, masking tape and tracing paper
- Pattern materials: draft paper for the first drawing, manila sheets for working patterns, and hard manila or carton for the final patterns
- Cutting and marking: scissors and a sharp knife, cutting board, tracing wheel, set of punches with a hammer, and a rasp file for smoothing pattern edges
- For you: a work table, a stool, and an overall or dust coat
A last is chosen by the size of the foot, so measure first.
- Stand the person on a sheet of paper with their weight on both feet and draw round the foot with the pencil held upright.
- Measure the foot length from the back of the heel to the tip of the longest toe.
- Measure the ball girth by passing the tape measure round the widest part of the forefoot.
- Measure the instep girth round the highest part of the middle of the foot.
Record in millimetres or centimetres. Shoe sizes have their own units: one Paris point (European size) is two-thirds of a centimetre, about 6.7 mm, and one English size is one-third of an inch, about 8.5 mm. A standard size chart turns the foot length into a size. Select a pair of sandal lasts of that size, with a toe shape and heel height that suit the design.
Pattern makers use imaginary lines on the last as guides:
- Feather line: the edge where the bottom of the last meets its sides
- Front centre line: from the middle of the toe, up over the top of the last
- Back centre line: from the middle of the heel seat straight up the back
- Joint line: across the widest part of the last, where the toes bend
Step 1: Study the design
Look at the sketch of the sandal. Is it a slide with one wide band, a cross-strap sandal, a toe-post sandal, or one with an ankle strap? Count the parts, note where each strap starts and ends, and note the colour of each part. A good design is simple: the straps hold the foot firmly without rubbing.
Step 2: Mask the last
Tear the masking tape into strips. Cover the bottom of the last first, then the top and sides, with strips that overlap by about half their width. Put on two layers, the second across the first, and rub them down so there are no wrinkles or gaps.
Step 3: Draw the main lines and trace the design
Draw the feather line by running the side of the pencil along the edge of the bottom. Draw the front and back centre lines and the joint line. Then, in a different colour, draw the straps on the tape exactly where the design shows them, on the outside and the inside of the last. Use tracing paper to copy a shape from the sketch if it is hard to draw freehand.
Step 4: Remove the tape and stick it on draft paper
Cut through the tape along the feather line with a sharp knife, taking care not to cut into the last. Peel off the bottom piece: this is the shape of the insole. Peel off the upper piece slowly so that it does not stretch or tear. Stick both pieces on draft paper, smoothing from the middle outwards. Where the tape will not lie flat, make small cuts at its edge.
Step 5: Cut the master pattern
Cut round the pieces stuck on the draft paper. This is the master pattern, also called the standard. It shows the whole sandal with no allowances added.
Step 6: Develop and cut the parts
Trace each part from the master pattern onto fresh paper and add the allowance it needs:
- Insole: the bottom shape exactly as it is
- Sole: the insole shape plus about 3 to 5 mm all round, which is trimmed after the sole is attached
- Straps: add a lasting allowance of about 15 to 20 mm at each end that passes under the insole, and about 4 to 5 mm on any edge that will be folded
Cut out each part.
Step 7: Transfer to hard manila
Lay each paper part on hard manila or carton. Run the tracing wheel along the lines, or draw round the part with a sharp pencil, then cut out the hard pattern. Smooth rough edges with the rasp file.
Step 8: Insert marking points
With a punch and hammer on the cutting board, make small holes to show the centre of each strap, where straps cross, where a buckle goes, and the slots in the insole where the strap ends pass through. Write on every pattern the part name, the size, the colour and the number to cut.
Step 9: Grade the patterns and group them into sizes
Grading means making the same patterns in other sizes. For one European size up, the insole grows by about 6.7 mm in length and a little in width; for one size down it shrinks by the same amount. The straps grow or shrink in proportion. Check each graded pattern against a last of that size. Punch a hole in each pattern and tie the patterns of one size together, so that sizes are never mixed.
Maria's foot is 24 cm long. On the size chart this is size 38, so she selects a size 38 sandal last. Her design is a slide sandal with two straps that cross over the toes. She masks the last, draws the main lines and the two straps, then peels off the tape and sticks it on draft paper. From the master pattern she develops four parts: an insole, a sole 4 mm bigger all round, and two straps with 15 mm added at each end. She transfers them to hard manila, punches the crossing points, labels each one and ties the set together.
An error of 2 mm on a pattern is repeated on every piece cut from it. Measure twice, keep the pencil sharp and cut exactly on the line.
- Cut on the cutting board, away from your body and from the hand that holds the work. Carry knives with the blade covered and scissors closed.
- For a small cut, wash it with clean water, press on it with a clean cloth until the bleeding stops, cover it with a plaster and tell your teacher. A deep cut needs a health worker.
- Do not bend patterns or cut on top of them.
- Put paper offcuts and used masking tape in the waste bin and sweep the table and floor.
- Wipe the tools, take the tape off the lasts, and return everything to its place.
- Store patterns flat, or hanging on a hook through the punched hole, in a dry place away from sunlight, grouped by design and size.
A small footwear workshop in Arusha keeps a set of hard patterns for each sandal design in every size it sells. When an order comes in, the maker picks the right set and cuts the leather straight away, so every pair comes out the same and little leather is wasted.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select appropriate tools and equipment
- Distinguish different colours
- Identify the required designs
- Select shoe lasts
- Prepare masking tapes
- Prepare tracing papers
- Cover shoe lasts with masking tapes
- Trace the shoe last based on the designs
- Draw the main lines correctly
- Remove the traced masking tapes
- Stick masking tapes on draft papers
- Cut master patterns
- Develop the patterns
- Cut different parts of footwear patterns
- Transfer patterns into hand carton or manillas
- Grade patterns correctly
- Insert marking points correctly
- Group patterns into sizes
- Clean the workplace thoroughly
- Observe safety
- Clean workplace thoroughly
- Clean tools and equipment thoroughly
- Store patterns correctly
- Store tools and equipment correctly
Tathmini ya matokeo
A patterns of sandal are designed as per specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should be able to:
- Take foot measurement correctly
- Mask shoe lasts correctly
- Trace different designs
- Trace the standard line patterns
- Transform sketches
- Produce master patterns
- Develop patterns correctly
- Grade patterns correctly
Principles: The student should explain the principles of:
- Designing
- Taking foot measurements
- Pattern cutting
- Standard size chart
Theories: The student should correctly explain:
- Types of pattern materials.
- Imaginary lines of lasts
- The units of measurement used in footwear making.
- Designing techniques
- The importance of precision and detail work when making patterns
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling of tools and equipment
- Safe handling of patterns
- First aid
- Waste disposal
Swali
Which tool is used to draw the feather line on a sandal last?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado