Mada za sehemu hiiDesigning intermediate patterns for footwear projectsMada 4
- Making Oxford shoe patterns
- Making sandal patterns
- Making training shoe patterns
- Making military boot patterns
Military boot patterns are the flat templates used to cut every part of a high, lace-up boot made for hard outdoor work. The patterns are developed on a shoe last, the foot-shaped block on which the boot is built, so that the finished boot fits the foot and matches the specification.
A pattern maker must know the main sizing systems and their units.
| System | Unit of one size | Notes |
|---|---|---|
| European (Paris point) | two-thirds of a centimetre, about 6.7 mm | Whole sizes such as 40, 41, 42 |
| English (UK) | one-third of an inch, about 8.5 mm | Half sizes are also made |
| American (US) | the same unit as the English system | The number is about one size higher |
| Mondopoint | millimetres | The size is the length of the foot itself, for example 265; used by many armies |
A foot 265 mm long is Mondopoint 265, which is close to European 42 and English 8.
- Measuring and drawing: tape measure, rulers, square, pencils in different colours and an eraser
- Working on the last: a pair of boot lasts, masking tape and tracing paper
- Pattern materials: draft paper for first drawings, manila sheets for working patterns, and hard manila or carton for the final patterns
- Cutting and marking: scissors and a sharp knife, cutting board, tracing wheel, set of punches with a hammer, and a rasp file for smoothing pattern edges
- Also: work table, stool, overall or dust coat, safety gloves and plastic boxes
The design lists the parts, the height of the leg, the number of eyelets and the colour of the leather. A typical boot has a vamp over the front of the foot, sometimes a toe cap, an inside and an outside quarter that form the leg, a bellows tongue joined to the quarters to keep out water and sand, a back strap covering the back seam, a counter round the heel and a padded collar at the top.
Step 1: Take measurements and select the last
Measure the foot length, the ball girth, the instep girth, the ankle girth and the girth of the leg at the height of the boot top. Select a pair of boot lasts of the right size from the size chart.
Step 2: Mask the last
Cover the whole last with overlapping strips of masking tape, in two layers laid across each other, and rub them down without wrinkles or gaps.
Step 3: Draw the main lines
These imaginary lines of the last guide every design:
- Front centre line: from the middle of the toe, up over the instep to the top of the last
- Back centre line: from the middle of the heel seat straight up the back
- Feather line: the edge where the bottom of the last meets its sides
- Joint line: across the widest part, where the foot bends
Mark the vamp point on the front centre line where the toes join the foot; the lacing starts just behind it.
Step 4: Sketch the design on the last
In a different colour, draw the vamp line, the toe cap line, the line of the eyelets and the edge of the counter on the tape, on both sides of the last. Use tracing paper to copy shapes from the design sketch where this helps.
Step 5: Remove the tape and cut the master pattern
Cut through the tape along the front and back centre lines with a sharp knife and peel off the outside half and the inside half without stretching them. Stick each half on draft paper, making small cuts at the bottom edge so that it lies flat. Cut the two shapes out, lay one on the other, and where they differ draw one line midway between them. The last stops near the ankle, so extend the shape upward on the paper to the height of the boot, using the ankle and leg measurements. Cut it out: this is the master pattern, also called the standard.
Step 6: Develop and cut the parts
Trace each part from the master pattern onto fresh paper and add its allowances:
- Lasting allowance: about 15 to 20 mm along the bottom edge, to be pulled under the insole
- Underlay allowance: about 8 to 10 mm where one part lies under another, such as the vamp under the quarters
- Folding allowance: about 4 to 5 mm on edges that will be folded
- Seam allowance: about 2 mm for a closed seam such as the back seam
Cut out every part. Lining patterns are developed from the same master pattern.
Step 7: Transfer to hard manila
Lay each paper part on hard manila or carton, transfer the lines with the tracing wheel or a sharp pencil, cut out the hard pattern and smooth its edges with the rasp file.
Step 8: Insert marking points
With a punch and hammer on the cutting board, mark the eyelet positions at equal spacing, the line where the vamp meets the quarters, and the centre of the tongue and toe cap. Label every pattern with the part name, the size, the colour and the number to cut.
Step 9: Grade the patterns and group them into sizes
Grading means making the same set in other sizes. For one European size up, the bottom grows by about 6.7 mm in length, and the widths and the leg grow in proportion; for one size down they shrink by the same amounts. Keep each size as a complete set in its own labelled plastic box.
A workshop receives an order for black boots in size 42, 20 cm high, with eight pairs of eyelets. Juma selects size 42 lasts, masks one, draws the main lines and the design, peels off the two halves and makes the master pattern, extending the leg to 20 cm. He develops the eight patterns, from vamp to collar. On each quarter he adds 18 mm of lasting allowance at the bottom and 5 mm of folding allowance at the top, and punches eight equally spaced eyelet marks. He transfers the labelled set to hard manila and stores it in a box marked size 42.
An error of 2 mm on a pattern is repeated on every boot cut from it, and parts that do not match cannot be stitched properly. Measure twice, keep the pencil sharp and cut exactly on the line.
- Cut on the cutting board, away from your body, with a safety glove on the hand that holds the work. Carry knives with the blade covered.
- For a small cut, wash it with clean water, press on it with a clean cloth until the bleeding stops, cover it with a plaster and tell your teacher. A deep cut needs a health worker.
- Do not bend patterns or cut on top of them.
- Put paper offcuts and used masking tape in the waste bin and sweep the table and floor.
- Wipe the tools, take the tape off the lasts, and return everything to its place.
- Store the boxes of patterns in a dry place away from sunlight, with the patterns lying flat.
A footwear workshop in Dar es Salaam that makes strong boots for security guards keeps a boxed set of hard patterns for every size it sells. With accurate patterns it can cut many pairs that all fit and look the same, and waste less leather.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Distinguish different colours
- Identify the required designs
- Select shoe lasts
- Prepare masking tape
- Prepare tracing paper
- Cover the shoe last with masking tape
- Trace the shoe last as per design
- Draw the main lines
- Remove the traced masking tape
- Stick on draft paper
- Sketch the design
- Cut master patterns
- Develop the patterns
- Cut different parts of footwear patterns
- Transfer into hand carton or manilla
- Grade patterns
- Insert marking points
- Group patterns into sizes
- Clean workplace
- Observe safety
- Clean tools and equipment
- Store patterns
- Store tools and equipment
Tathmini ya matokeo
Military boot patterns are designed according to shoe specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student are to be able to:
- Take foot measurement
- Mask shoe lasts
- Trace different designs
- Trace standard pattern lines
- Transform sketches
- Produce master patterns
- Develop patterns
- Grade patterns
Principles: The student should correctly explain the principles of:
- Designing
- Taking foot measurements
- Pattern cutting
Theories: The student should clearly explain:
- Types of pattern materials
- Imaginary lines on the lasts
- The units of measurement used in footwear making
- Designing techniques
- Importance of precise and detailed work while making patterns
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling of tools and equipment
- Safe handling of patterns
- First aid
- Waste disposal
Swali
Which international sizing system uses millimetres and bases the size number on the actual foot length?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado