Mada za sehemu hiiMaking intermediate leather goodsMada 4
- Making wallets
- Making travelling bags
- Making briefcase
- Making jackets
Making Wallets
A wallet is a small folding case used for carrying money, cards, and identification. In this lesson, you will learn about the types of wallets, the tools and materials needed, and the step-by-step procedures for making a wallet.
Understanding the different types of wallets helps you choose the right design for your project.
-
Bi-fold wallet: A wallet designed to fold in half. It is one of the most popular wallet styles because it is compact and fits easily into pockets.
-
Trifold wallet: A wallet with three sections that folds twice. It offers more compartments than a bi-fold wallet but is thicker.
-
Cardholder: A typically flat, folded pouch with various sections that hold cash (including coins), credit cards, ID, and other small items such as stamps and passes. It is ideal for people who carry fewer items.
The following tools and equipment are needed for making wallets:
- Workbench
- Silver pen (for marking)
- Sewing machine
- Skiving machine
- Knife (cutting knife or skiving knife)
- Spirit lamp
- Pricking iron
- Awl
- Set of hole punches
- Hammer
- Cutting board
- Set of brushes
- Glue container
- Measuring tape
- Wallet patterns
- Spray gun
- Scissors
- Steel ruler
- Spring clamps
The most common material for making wallets is leather, which is favoured because of its aesthetic appearance, durability, and desirable physical properties. Other materials used include:
- Fabric (as an alternative to leather)
- Glue (upper glue for bonding)
- Sewing thread
- Finishes (for protecting and decorating the wallet)
- Lining materials
- Edge binding materials
Follow these steps carefully to make a quality wallet:
1. Prepare the Working Area
Arrange all tools and materials on a clean, flat workbench before starting. Ensure your working area is well-organized and free from clutter.
2. Select and Cut Materials
- Prepare the leather to be cut.
- Prepare a wallet pattern and lay it on top of the leather.
- Use a silver pen to transfer the pattern lines onto the leather.
- Cut the leather pieces carefully using scissors or a skiving knife.
- Repeat these steps for cutting all pieces according to the design.
3. Burnish the Short Edges
Burnish the two short edges before gluing and sewing, as it will be difficult to do later. Apply a little oil to the edges if they are too dry. Keep repeating the process until the edges have slightly darkened and smoothed out.
4. Make the Side Folds
- Mark the side and middle fold lines on the flesh side (the fuzzy side) of the leather using a bone folder or silver pen.
- Use clamps to protect leather scraps from getting marks.
- Clamp until dry, then check the fold. If not well-folded, moisten the leather again and pound with a mallet to flatten.
- Moisten the middle fold line and fold the leather in half carefully, ensuring all edges line up neatly.
- Put the fold into the stitching pony and clamp the sides.
- Groove the stitching lines on the inside pockets using a groover on dry leather.
5. Glue Down the Pockets
- Use a piece of tape or paper as a guide to apply the glue.
- Apply the glue just along the edge of the inside pockets.
- Clamp or hold until dry.
6. Punch the Sewing Holes
- Lightly moisten the leather, wait until it is almost dry, then line up the chisels to punch holes.
- Place the wallet on a piece of cardboard.
- Use a sharp awl and punch straight through the holes (do not angle the punch, or holes will come out crooked).
- For best results, use a diamond chisel for marking points and a sharp awl for punching holes.
7. Stitch the Wallet Pockets
- Use about 16 ply of thread for hand stitching.
- If using a sewing machine, set the machine according to the thickness of the material.
8. Sand the Long Edges or Trim
Use fine-grit sandpaper to sand down the long sides of the wallet to ensure both layers of leather and pockets line up correctly. The width for edge trimming is generally 0.5–3 mm.
9. Burnish the Long Edges
Use an edge burnisher to burnish these edges similar to the short edges. Add oil if the edges are dry, and apply edge finishes such as wax, dyes, or other available finishes.
10. Clean Tools, Equipment and Machines
Cleaning of tools and equipment should be done after each use:
- Power down the machine and remove the thread and needle for safety.
- Clean the working area.
- Clean the bobbin housing.
- Oil the machine in all rotating parts.
- Inspect the needle plate.
- Regulate the stitch selector and check tension.
Specifications: 8 cm width and 18 cm length
Materials needed: leather, glue, lining, finishes, and sewing thread
Tools and equipment needed: skiving machine, sewing machine, cutting machine, knife, spirit lamp, awl, set of hole punches, hammer, pencil, cutting block, set of brushes, glue container, measuring tape, workshop stool, cutting patterns, scissors, and cutting dies
Procedures:
- Sketch the wallet on paper.
- Construct patterns.
- Lay a piece of leather on a flat table surface.
- Cut the leather according to patterns and cutting dies.
- Perform burnishing of leather.
- Join all pieces of leather (assembling) according to the design using adhesives.
- Perform stitching.
- Perform finishing.
In Tanzania, skills in wallet making can help small-scale leather artisans start small businesses producing and selling locally made wallets at markets like Mwenge, Slipway, or local shopping centres. A student could make a bi-fold leather wallet using locally sourced leather and sell it for between TZS 20,000 to TZS 50,000 depending on the quality, providing both income generation and practical application of vocational skills.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to: correctly:
- Interpret different designs
- Select tools and materials
- Estimate the amount of leather required based on the design
- Select materials
- Lay patterns on leather and trace around them
- Cut out leather
- Assemble leather pieces using glue
- Stitch the leather product
- Insert lock
- Clean the leather product
- Spray and polish
- Pack into packing materials
- Observe safety
- Store finished leather products
- Clean tools, equipment and machines
- Store tools and equipment
Tathmini ya matokeo
Wallets are made according to the specifications
Tathmini ya maarifa
Knowledge Evidence: Detailed knowledge of:
Method used: The student should clearly explain how tomake leather wallet
Principles: The student should clearly explain the principles of:
- Adopting patterns into leather goods making
- Operating tools, equipment and machines
- Pattern making
- Hand cutting
- Machine cutting
- Folding
- Sewing
Theories: The student should clearly explain:
- Different types of leather work accessories and fittings
- Different types of leather finishes
- Proper use of tools, equipment and machines
- Different designs and styles of leather products
- Uses of different types of accessories and fillings
- Importance of precision and attention to details when making leather goods
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions for leather goods making
- Safe handling of work tools, equipment and machines
- First aid
- Waste disposal
Swali
Which of the following is NOT a type of wallet described in the lesson?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado