Mada za sehemu hiiMaking intermediate leather goodsMada 4
- Making wallets
- Making travelling bags
- Making briefcase
- Making jackets
A jacket is an upper-body garment that covers the torso and arms. It is made from leather or fabric and includes features like a collar, sleeves, zipper or buttons, and lining for comfort and warmth. Making a jacket combines measuring, cutting, assembling, and finishing skills.
Start by reading the design. Common styles of leather jacket are the bomber (short, with a ribbed or elasticated waist and cuffs), the biker (close-fitting, with a slanted front zipper and wide lapels) and the blazer (longer, with a buttoned front). The design shows the number of panels, the kind of collar and pockets, and the fastenings.
- Leather: jackets need soft, thin garment leather, about 0.6 to 1 mm thick, usually from sheep or goat skins, or soft cow leather for a heavier jacket. Smooth leather is easy to wipe clean; suede and nubuck have a brushed surface and mark more easily.
- Lining: choose a smooth, light fabric such as polyester or viscose coat lining so that the jacket slides on easily. Cotton is cooler but less slippery.
- Reinforcements: thin interfacing is placed behind the collar, front edges, cuffs and pocket openings so that they keep their shape and do not stretch.
- Accessories and fittings: zippers, buttons, press studs, buckles, and polyester or nylon thread strong enough for leather.
- Tools: measuring tape, cutting and marking patterns, silver pen, knife and scissors, cutting block, hammer, awl, hole punches, dividers, brushes for glue, a creaser (also called a greaser) with a spirit lamp, a spray gun, and a sewing machine fitted with a leather needle.
Leather is sold by area, often in square feet, and each skin has an uneven shape with thin or scarred places that cannot be used. Lay all the pattern pieces close together, measure the area they cover, and add about one-quarter more for waste. Remember that most pieces are cut as a pair, one for the left side and one for the right. An adult jacket needs several skins, so choose skins that match in colour and thickness.
The process follows a clear sequence from planning to the finished product.
1. Taking Body Measurements
Accurate measurements ensure the jacket fits well. Key measurements include:
- Chest circumference – around the widest part of the chest
- Shoulder width – from one shoulder bone to the other
- Sleeve length – from shoulder to wrist
- Back length – from the neck base to the waist
- Neck circumference – around the base of the neck
2. Preparing Patterns
A pattern is a paper template that shows the shape of each jacket piece.
- Check each skin for scars, holes and thin places, then lay the cutting patterns on the leather so that flaws fall outside the pieces. Place the main pieces along the backbone of the skin, where the leather is strongest, and hold them down with weights, never pins
- Turn the pattern over to mark the second piece of each pair, so that you get a left and a right
- Lay the lining patterns on the fabric along the straight grain, and the reinforcement patterns on the interfacing
- Use a silver pen or chalk to trace around the pattern edges
- If the pattern does not already include seam allowances, add about 1 cm around each traced line
- Mark notches, button positions, and pocket locations on the material
3. Cutting the Material
- Place the material on a cutting block to protect the workbench
- Use a sharp knife or scissors to cut the leather along the marked lines, and scissors to cut the lining and interfacing. In a factory the pieces are cut by machine, with steel dies on a cutting press
- Cut precisely to avoid waste or ill-fitting pieces
- Cut matching pieces for the left and right sides of the jacket
4. Assembling the Jacket
Leather shows every needle hole, so a wrong seam cannot be unpicked and sewn again without leaving marks. Hold pieces together with clips or a thin line of glue, not pins, and use a longer stitch of about 3 to 4 mm, because stitches that are too close together can tear the leather. First glue the reinforcements to the flesh side of the collar, front edges and cuffs. Then follow this order when joining pieces:
- Join the body panels – stitch the front and back panels together at the sides and shoulders. After stitching each seam, open the seam allowances, glue them down with a thin coat of upper glue and tap them flat with the hammer
- Attach the sleeves – hold each sleeve to the armhole with clips, matching the notches, and stitch in place
- Insert the zipper – position the zipper at the front opening and stitch using a sewing machine or by hand
- Add the collar – cut, shape, and stitch the collar at the neckline
- Attach fasteners – sew on buttons, or punch holes for press studs with the hole punch and set them with the hammer
5. Adding Lining
Lining improves comfort and gives the jacket a professional finish.
- Cut the lining fabric to match the inner shape of the jacket panels
- Stitch the lining pieces together, body and sleeves, to make a second jacket in fabric
- Place the lining inside the leather jacket and stitch it to the front edges and neckline, then to the hem and the ends of the sleeves, with the edges of the leather folded in
6. Finishing
- Trim excess seam allowance
- Fold the hem, cuff and front edges in along a straight line, glue them and tap them flat
- Warm the creaser (greaser) over the spirit lamp and run it along the folded edges to press a neat line into the leather. Test the heat on a scrap first, because a tool that is too hot scorches leather
- Brush on upper glue where needed to secure loose edges
- Press seams flat with an iron on fabric jackets only. Never put a hot iron straight onto leather; flatten leather seams with glue and a hammer
7. Cleaning, Spraying, Packing and Storing
- Trim thread ends, rub off glue marks and wipe the jacket with a soft, slightly damp cloth
- Spray a thin, even coat of leather finish with the spray gun in a well-ventilated place, wearing a mask, then polish with a soft cloth or brush when it is dry
- Hang the jacket on a wide, shaped hanger and cover it with a cloth or paper garment bag. Do not seal leather in airtight plastic for a long time, because trapped moisture causes mould
- Store finished jackets hanging in a cool, dry place away from direct sunlight, not folded or pressed tightly together
A student in a school workshop in Iringa needs to make a simple leather jacket for a customer.
- Measure the customer's chest = 96 cm, shoulder width = 42 cm, sleeve length = 58 cm
- Select the cutting pattern for a 96 cm chest and trace it onto matching garment leather skins, avoiding flaws
- Cut the front panel, back panel, two sleeves, and collar pieces
- Stitch the shoulder seams, then the side seams
- Attach sleeves to the armholes
- Insert a 60 cm zipper at the centre front
- Add the collar and stitch it to the neckline
- Line the jacket with a plain cotton lining
- Finish the edges with a warm creaser, clean the surface, then spray and polish it
The result is a fitted leather jacket, ready to be packed for the customer.
- Wear safety boots and an overall or dust coat while working
- Handle knives and hole punches carefully to avoid cuts
- Upper glue and spray finishes catch fire easily. Close the glue tin and move it well away before lighting the spirit lamp, and put the lamp out as soon as you finish creasing
- Work in a well-ventilated area when using glue or finishing chemicals
- Keep fingers, sleeves and long hair away from the needle of the sewing machine, and switch it off before changing the needle or the bobbin
- For a small cut, wash it with clean water, press on it with a clean cloth until the bleeding stops and cover it with a plaster. Cool a burn under clean running water for about 20 minutes. Report every injury
- Keep large leather offcuts for small goods and put the rest in the waste bin. Put empty glue tins and glue-soaked rags in the container for hazardous waste; never burn them
- Wash the spray gun and glue brushes after use, brush lint from the sewing machine, wipe the tools and return them to their places
In Tanzania, tailors and vocational trainees who can make jackets using leather or fabric earn income by supplying local markets, schools, and tour companies — a well-made jacket earns a price that depends on its material and design, providing a useful income stream for small businesses in towns like Arusha, Mwanza, and Dar es Salaam.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to correctly:
- Interpret different designs
- Select tools and materials
- Estimate the amount of leather required based on their designs
- Select fabric lining
- Lay patterns on leather and trace around them
- Lay patterns on fabric and trace around them
- Lay patterns on reinforcements
- Cut out leather
- Cut out fabrics
- Assemble leather pieces using glue
- Stitch the leather product
- Insert locks
- Clean the leather jackets
- Spray and polish.
- Pack into packing materials.
- Observe safety.
- Store finished leather products
- Clean tools, equipment and machines.
- Store tools and equipment
Tathmini ya matokeo
Jackets are made according to their specifications and measurements
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to make leather jacket
Principles: The student should clearly explain the principles of:
- Adopting patterns into leather jackets
- Operating tools, equipment, and machines
- Pattern making
- Hand cutting
- Machine cutting
- Folding
- Sewing
Theories: The student should clearly explain:
- Different types of leather materials and their characteristics
- Different types of fabrics
- Different types of leather work accessories and fittings
- Different types of leather finishes
- Proper use of tools, equipment, and machines
- Different designs, styles of leather jacket
- Uses of different types of accessories and fillings
- The importance of precision and attention to details when making jackets
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions for making leather goods
- Safe handling of work tools, equipment, and machines
- First aid
- Waste disposal
Swali
Which leather is most suitable for making a jacket?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado